Artel INFINITYLINK ILC450 Operating and maintenance instructions

InfinityLink ILC450 - 10G HD/SD-SDI, ASI
IP Gateway & GigE Data Transport
•Mon Mini BNC - In TX mode, this mini BNC outputs a copy of the ASI, SD-SDI, HD-SDI signal received
on the BNC in connector on the Rear Panel. In RX mode , this BNC outputs a copy of the ASI, SD-SDI,
HD-SDI signal sent out the BNC out on the Rear Panel.
•RST Pushbutton - Pressing, holding in for more than 4 seconds, and then releasing this button will
reset the module interrupting data transmission through the module. Reset is similar to power-up
sequence of module. No user configuration data is changed during this reset.
ILC450 Front Panel:
1
4
3
2
1
4
3
2
5
Module Settings Configuration
1Operational Mode Sets Operational Mode relative to the 10G Video Circuit.
2Video Enable/disable video transport over the 10G link.
31G Ethernet Port for 1G traic. Options are disabled, SFP, or backplane where
available.
4Jumbo Frames Enables support for IP Frames that are greater than 1518 bytes and up to
9216 Bytes in size.
5IP Address IP address Module uses as the source address when Transmitting Video
over the 10G interface (see ILC450 manual for further details).
6Video Alarm Enable Alarm on loss of active video.
710G SFP+ Alarm Enable Alarm on 10G SFP+ not present.
81G SFP Alarm Enable Alarm on 1G SFP not present.
Receiver Settings Configuration
1Source IP Addr IP address that Module uses in Unicast mode to receive from.
2Multicast Group Multicast address that Module uses in Multicast mode to receive from.
3Port Port number setting must match the Port number setting on the TX module
that you wish to receive from.
4Recovery Buer
Specifies small or large recovery buer size. Buer size determines latency.
This is further determined by the Video format applied (see ILC450 manual
for further details).
Transmitter Settings Configuration
1Video Source Sets input port for video to “In BNC” or available backplane inputs.
2Destination
IP Addr
Sets destination IP address to either the Multicast Group or the IP Address
of the Transmitter
3Port Port number setting must match the Port number setting on the RX module
that you wish to transmit to.
4Time to Live Sets number of route hops that a packet may make before it is dropped.
5FEC Mode
Specifies Forward Error Correction (FEC) settings
• Specify Column or Row/Column or No FEC
• Specify matrix (row and column) size (maximum Row x Column: 3000(HD),
1500(SD), 100(ASI). (See ILC450 manual for further details.)
* Note: Confirm your network settings before connecting to your network.
Video Signal Types Configuration
1HD-SDI Discretely enables output of HD-SDI.
2SD-SDI Discretely enables output of SD-SDI.
3ASI Discretely enables output of ASI.
1
4
3
2
7
6
5
8
1
3
2
Artel ships the ILC450 congured as follows:
QUICK START GUIDES

LED Function Color Description
OK Module
Status
OFF No power.
nGreen No alarms.
nYellow Minor alarm.
nRed Major alarm.
TX
(Mode)
Transmitter
Mode
Indicator
OFF Receiver mode is selected.
nGreen TX Mode: Valid video format as
configured in IL Manager.
nYellow TX Mode: No video format detected
as configured in IL Manager.
Yellow TX Mode: In Unicast mode and no
arp reply.
nRed TX Mode: No link.
RX
(Mode)
Receiver
Mode
Indicator
OFF Transmitter mode is selected.
nGreen
RX Mode: Valid video detected on
10G interface with correct IP
configuration.
nYellow RX Mode: No video input at receiver.
Yellow Packet errors detected.
nRed RX Mode: No link.
1G 1G SFP Link
OFF 1G not enabled.
nGreen Link established.
Green Link established with activity.
nYellow RX optical power high.
Yellow 1G Ethernet enabled, errors
detected.
nRed No link.
Red No SFP installed, low light, or loss of
signal.
ASI
ASI Signal
Mode
Indicator
OFF ASI disabled or other rate detected.
nGreen ASI enabled and ASI detected.
nYellow ASI enabled but no signal detected.
nRed Input fault or ASI not enabled but
ASI detected.
SD
SD Signal
Mode
Indicator
OFF SD disabled or other rate detected.
nGreen SD enabled and SD detected.
nYellow SD enabled but no signal detected.
nRed Input fault or SD not enabled but SD
detected.
HD
HD Signal
Mode
Indicator
OFF HD disabled or other rate detected.
nGreen HD enabled and HD detected.
nYellow HD enabled but no signal detected.
nRed Input fault or HD not enabled but
HD detected.
Flashing green | Flashing yellow | Flashing red
Note: Install an Artel SFP+ in socket A only. Install an SFP in Socket B only.
ILC450 FRONT PANEL LEDS
LED Function Color Description
OK Module
Status
OFF No power.
nGreen Normal operation.
nYellow Minor alarm.
nRed Major alarm.
TX
(Mode)
Transmitter
Mode
Indicator
OFF Receiver mode is selected.
nGreen TX Mode: Valid video format as
configured in IL Manager.
nYellow TX Mode: No video format detected
as configured in IL Manager.
Yellow TX Mode: In Unicast mode and no
arp reply.
nRed TX Mode: No link.
RX
(Mode)
Receiver
Mode
Indicator
OFF Transmitter mode is selected.
nGreen
RX Mode: Valid video detected on
10G interface with correct IP
configuration.
nYellow RX Mode: No video input at receiver.
Yellow Packet errors detected.
nRed RX Mode: No link.
TX (10G)
10G
Transmitter
Mode
OFF Not valid during normal operation.
nGreen TX Mode: Normal operation.
nRed TX Fault
Red No SFP+ Installed
RX (10G)
10G
Receiver
Mode
OFF Not valid during normal operation.
nGreen Link established.
Green Link established with activity.
nYellow RX optical power high.
nRed No link.
Red No SFP+ installed, low light, or loss
of signal.
TX (1G)
1G
Transmitter
Mode
OFF 1G not enabled.
nGreen Normal operation.
nRed TX fault.
Red No SFP installed.
RX (1G)
1G
Receiver
Mode
OFF 1G not enabled.
nGreen Link established.
Green Link established with activity.
nYellow RX optical power high.
Yellow 1G Ethernet enabled, errors
detected.
nRed No link .
Red No SFP installed, low light, or loss
of signal.
ILC450 REAR PANEL LEDS
AR208-006450-B00_B
Install SFP+s
T: 978-263-5775
www.artel.com
[e-mail]
customercar[email protected]om
Sales
InfinityLink ILC450 - 10G HD/SD-SDI, ASI IP Gateway & GigE Data Transport