Artel InfinityLink ILC410 User manual

27
InfinityLink ILC410 - SD-SDI or ASI 2 Ch
Bi-Directional IP Gateway
CHANNEL A (OR B) RECEIVE Configuration
Configures settings for data received from ILC410 IP network
1RECEIVER: Enable Channels to RECEIVE video from network
2Source IP Address of ILC410 or SMPTE 2022 based Ethernet transmitter
3IP Multicast group Address
Special multicast address ILC410 receives traic from during multicast reception
4TC/IP PORT Address
Logical TCP port address that ILC410 receives traic on
5
RECOVery Buer1 Size to handle late arriving and misordered packets
(see ILC410 manual for more info)
• Large setting provides greater ability to receive late and misordered packets
• Recovery Buer Size and FEC settings determine ILC410 latency (see manual)
1. In ASI mode, only the small buer setting should be used to avoid excessive latency
Module Settings
1
IP Address of ILC410 Module
• This is the source IP address of all traic transmitted and the destination IP address of all traic
received
• Also the address that responds to “Pings”
2
VLAN ENABLE/DISABLE and Configuration
• Specifies whether VLAN tag is populated on outgoing Ethernet frames
• Specifies VLAN ID that is set on outgoing Ethernet frames
• Specifies VLAN priority (1 through 7; 1=low, 7=high)
• VLAN ID/VLAN priority only display when VLAN Enable selected
3VIDEO MODE for Channel A and B
Specifies video mode for all channels (ASI or SDI/SDTI)
4ENABLE ALARM on loss of active video
If enabled, alarm will activate if active video signal is lost
5ENABLE ALARM ON SFP not present
If enabled, alarm will activate if an SFP is not installed
?ILC410 Module or Receiver or Transmitter Settings Help
Channel A (or B) Transmit Configuration
1Enable Channels to Transmit video to network
2
Transmit Video Source
• TRANSMIT video source BNC or other slot
• Selects source of transmit video
• For IL6000, displays backplane slots 1-4
3Destination IP Address of ILC410 or SMPTE 2022 based Ethernet receiver
4Logical TCP port address that IP packets are transmitted on. Number must be between 1 and 65535.
5Specifies IP Type of Service (TOS) bits for transmit data
Specifies IP priority level to route traic through network to destination
6
Specifies Forward Error Correction (FEC) settings
• Specify Column or Row/Column or No FEC
• Specify FEC matrix (row and column) size (maximum 1,500)
7
Specifies ASI bandwidth limiting (ASI mode only)
• If transmit ASI traic exceeds specified bandwidth, traic will be throttled
• ASI bandwidth limit/M2TS packing displays when ASI mode selected (module settings)
8
Specifies Number of MPEG frames per IP frame (ASI mode only)
• For lowest latency, choose 1 (least eicient use of bandwidth)
• For most eicient use of bandwidth, choose 7
Transmitter Settings
1
2
3
4
5
6
7
8
Receiver Settings
1
2
3
4
5
Module Settings
1
2
3
4
5
QUICK START GUIDES

28
LED Function Color Description
OK
ILC410
Module
Status
OFF No power or power fault
nGreen No alarm
nYellow Minor alarm
nRed Major alarm
SDI Operating
Mode
OFF ASI Mode
nGreen SDI Mode
TX Transmitter
Status (A, B)
nGreen Normal operation
nRed SFP TX failure exists
Red No SFP is installed
RX Receiver
Status (A, B)
nGreen Normal operation
Yellow Optical Rx power too high
Red A low receive power condition exists
ACT Ethernet
Activity
nGreen Link present
Green Link activity
IN A,
IN B
TX
Channel
Status
OFF Channel is disabled
nGreen Video is received
nYellow No signal detected
nRed Improper video input
Red DVB-ASI rate limited
OUT A,
OUT B
RX
Channel
Status
OFF Channel is disabled
nGreen Video is received
Green Successful FEC
Green | Red Unsuccessful FEC
nYellow Provisioned but not receiving IP packets
nRed Improper video input
CHANNEL
SELECT
MON
Switch
Monitor Video Channel On
SMB Connector
Pressing Monitor Switch indicatesz which video channel (IN A, B or OUT A, B) is output on
MON SMB Connector. Pressing Monitor Switch while LEDs are flashing will advance monitor
output to next video channel
Flashing green | Flashing yellow | Flashing red
Install SFPs
ILC410 FRONT PANEL LEDS
AR208-006410-D00_A
T: 978-263-5775
www.artel.com
[email protected]om
customerc[email protected]om
Sales
InfinityLink ILC410 - SD-SDI or ASI 2 Ch Bi-Directional IP Gateway