L&S SMART GATEWAY Instruction manual

025-FIS18_Smart_GATEWAY 1
Wi-Fi command interface / RF 433.92 MHz for connection between L&S
receivers and devices with Wi-Fi connection.
INDEX
1 - PRODUCT FEATURES
1.1 - TECHNICAL DATA
1.2 - USE
2 - NETWORK CONFIGURATION
2.1 - INTRODUCTION
2.2 - PROCEDURE FOR USING A HOTSPOT CONNECTION
2.3 - PROCEDURA PER L’UTILIZZO CON RETE WIFI ESISTENTE
3 - SYSTEM CONFIGURATION
3.1 - INTRODUCTION
3.2 - CREATING A DEVICE / ASSOCIATING THE DEVICE WITH THE RECEIVER
3.3 - DELETING OR MODIFYING A CREATED DEVICE
3.4 - CREATING A GROUP
3.5 - DELETING OR MODIFYING A CREATED GROUP
4 - GENERAL SETTINGS
5 - USER INTERFACE WINDOWS
5.1 - INTRODUCTION
5.2 - HOMEPAGE/DEVICES
5.3 - ZONES
5.4 - SCENARIOS
5.5 - PROGRAMMING THE TIMER
6 - FURTHER DETAILS
6.1 - CREATING A QUICK ACCESS COMMAND
6.2 - VERIFY THE NETWORK IP ADDRESS
7 - RECALL A SCENARIO USING TRANSMITTER
7.1 - INTRODUCTION
7.2 - ASSOCIATION OF THE TRANSMITTER
7.3 - ASSOCIATING A SCENARIO WITH THE TRANSMITTER KEY
7.4 - DELETING A TRANSMITTER
8 - RESET THE SYSTEM
8.1 - RESET THE NETWORK CONFIGURATION
8.2 - RESET THE SYSTEM CONFIGURATION
SMART GATEWAY
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.

025-FIS18_Smart_GATEWAY 2
1 2
1.2 USE
To use the product you need:
- a Wi-Fi compatible device (e.g.: tablet, PC or Smartphone)
- Compatible radio receivers
To activate the system, follow the instructions in paragraph 2 on how to congure the hub network and access the
application. Next, follow the instructions in paragraph 3 on how to create user screens and associate them with the
receiver
63mm
67mm 72mm
1.1 TECHNICAL DATA
230Vac
Wi-
50
433.920MHz ISM
20
IP20
-20 +55 °C
174x46x35 mm
Power supply
Type of communication
Number of devices (mobile phones, PCs, etc.) simultaneously connected
Type of communication with receivers
Number of controllable receivers
Protection rating
Operating temperature
Dimensions
1 - PRODUCT FEATURES
Picture 1.1b
2.1 INTRODUCTION
The device can operate in two modes:
- the hub generates a Wi-Fi hotspot. To use the device, it must be connected to this network (therefore, not connected
to any other networks)
- connect the hub to an existing Wi-Fi network. Once congured, the hub can also be accessed when connected to the
existing network.
The rst solution is ideal for locations where no Wi-Fi network is available, but you wish to use a personal device for
driving the loads.
The second solution makes it possible to remain connected to existing Wi-Fi networks (e.g.: have internet access), while
using the hub at the same time.
According to the specications of the system, follow the instructions in:
- paragraph 2.2 to connect the hub for use with a hotspot
- paragraph 2.3 to connect the hub for use with an existing network
2 - NETWORK CONFIGURATION
Device with Wi-Fi
connection
(e.g.: Smartphone)
TYPE OF SYSTEM WITH HUB CONNECTED TO EXISTING WI-FI NETWORK
Existing Wi-Fi
Network
Hub100
Device with Wi-Fi
connection
(e.g.: Smartphone)
TYPE OF SYSTEM WITH HUB CONNECTED TO HOTSPOT
Hub100
A
KEY
Y key= reset network conguration
(if reset in hotspot with default password).
See paragraph 7.1
LED A
- Red/green/blue lights turn on in sequence when powered ON
- Flashes red while creating/connectiong to a network
- Blue light turn on if you set connecting to an existing network
- Red light turn on if you set creating a network hotspot
y
L&S
Receivers
L&S
Receivers

025-FIS18_Smart_GATEWAY 3
1 2
1.2 USE
To use the product you need:
- a Wi-Fi compatible device (e.g.: tablet, PC or Smartphone)
- Compatible radio receivers
To activate the system, follow the instructions in paragraph 2 on how to congure the hub network and access the
application. Next, follow the instructions in paragraph 3 on how to create user screens and associate them with the
receiver
63mm
67mm 72mm
1.1 TECHNICAL DATA
230Vac
Wi-
50
433.920MHz ISM
20
IP20
-20 +55 °C
174x46x35 mm
Power supply
Type of communication
Number of devices (mobile phones, PCs, etc.) simultaneously connected
Type of communication with receivers
Number of controllable receivers
Protection rating
Operating temperature
Dimensions
1 - PRODUCT FEATURES
Picture 1.1b
2.1 INTRODUCTION
The device can operate in two modes:
- the hub generates a Wi-Fi hotspot. To use the device, it must be connected to this network (therefore, not connected
to any other networks)
- connect the hub to an existing Wi-Fi network. Once congured, the hub can also be accessed when connected to the
existing network.
The rst solution is ideal for locations where no Wi-Fi network is available, but you wish to use a personal device for
driving the loads.
The second solution makes it possible to remain connected to existing Wi-Fi networks (e.g.: have internet access), while
using the hub at the same time.
According to the specications of the system, follow the instructions in:
- paragraph 2.2 to connect the hub for use with a hotspot
- paragraph 2.3 to connect the hub for use with an existing network
2 - NETWORK CONFIGURATION
Device with Wi-Fi
connection
(e.g.: Smartphone)
TYPE OF SYSTEM WITH HUB CONNECTED TO EXISTING WI-FI NETWORK
Existing Wi-Fi
Network
Hub100
Device with Wi-Fi
connection
(e.g.: Smartphone)
TYPE OF SYSTEM WITH HUB CONNECTED TO HOTSPOT
Hub100
A
KEY
Y key= reset network conguration
(if reset in hotspot with default password).
See paragraph 7.1
LED A
- Red/green/blue lights turn on in sequence when powered ON
- Flashes red while creating/connectiong to a network
- Blue light turn on if you set connecting to an existing network
- Red light turn on if you set creating a network hotspot
y
L&S
Receivers
L&S
Receivers

025-FIS18_Smart_GATEWAY 4
3 4
STEP1
Power ON the hub.
Red/green/blue lights turn on in
sequence. After the LED will ash
red during this phase (about 1
minute): the hub is generating the
Wi-Fi hotspot
2.2 PROCEDURE FOR USING A HOTSPOT CONNECTION
STEP3*
To connect to this network, insert
the default password:
"12345678"
NOTE: when connected to this
network, connections to other
networks will be disabled and
access to the internet is
unavailable
STEP2*
The LED switch ON and remain
xed on green:
use your own device (e.g.: Smar-
tphone) and search available
networks for "Hub Smart Control",
the hotspot generated by the hub.
STEP4*
You are now connected to the
hotspot generated by the hub.
Next, type the default name of the
hub, "http://hub100.", in the
address bar of the browser on
your device.
STEP5
The user interface window will
open. Click on "menu".
STEP6
Click on "Congure network"
NOTE: this operation is not
necessary for usage, but it makes
the hub more secure and blocks
unwanted access to the system.
STEP7*
You will be requested to enter a
password; the default password
is: “1234”.
STEP8
Click on "congure network"
STEP9
The current setting will be
displayed; click on "edit"
Hub Smart Control
ENTER PASSWORD
12345678
Access
Type a website address
Conrm Cancel
Password
Enter password
http://hub100.
Edit
Hub hotspot
Save
menu
lampeggia rosso
Devices
Settings
CONFIGURE NETWORK
Congure network
Devices
Settings
Congure network
Congure system
1234 congure network
Congure network
Congure current network
Type of access : Hub hotspot
SSID : Hub Smart Control
Edit network
Select connection type
Hub hotspot
Wi-Fi network
Edit
STEP10
Click on "Hub hotspot"
STEP11
Fill in all elds with the connection data for the hotspot you wish to create.
Network name (SSID): the name of the hotspot generated by the hub.
See step 2 of this procedure (default: Hub Smart Control)
Current password: the existing password required to connect to the
hotspot used in step 3 of this procedure (default: 12345678)
New password: the new password which will be used in step 3.
It is recommended to set a new password for security reasons.
System name: the name to enter in the address bar of step 4 of this
procedure. The name cannot contain spaces.
NOTE: when entering the name in the address bar, it must always end with
a full stop (.)
EXAMPLE:
system name: “hubcasa”
address to enter: “http://hubcasa.”
ATTENTION:
To access the system with another device (mobile phone, PC, etc.) once
the system has been congured, simply follow step 14.
The IP address to connect to is visible on the congure network page in
the settings menu of a device which has already been congured
STEP12
After lling in all the elds, click on
"Save" at the bottom of the page.
STEP13
The hub will restart to activate the new settings;
the LED will ash red while creating the hotspot
(about 1 minute).
The personal device will disconnect from the hub’s
hotspot network.
STEP14
To use the system, reconnect to the hub’s Wi-Fi
network (steps 2, 3 and 4 of this procedure) using the
new data entered during step 11.
NOTE: it is recommended to create an icon on the
homepage of the personal device so you can quickly
access the commands; see paragraph 6.1
NOTE:
it is important to remember the infor-
mation entered as it is required in order
to use the hub with your own device
and to connect more devices at a later
time.
If the data are lost, the system must be
reset by following the procedure in
paragraph 7.1.
Edit network
Select connection type
Hub hotspot
Network wi
Hub hotspot conection
Network name (ssid)
Current password
New password
Conrm
password
System
System Name
Save
Network name (ssid)
Current password
New password
Conrm
password
System
System Name
Save
Wi-Fi Activated
CHOOSE A NETWORK...
Hub Smart Control
*NOTE: In steps 2, 3, 4 and 7 of
this procedure, the default
values to be used will be
suggested. If these were modi-
ed previously, the system must
be reset; see paragraph 7.1.

025-FIS18_Smart_GATEWAY 5
3 4
STEP1
Power ON the hub.
Red/green/blue lights turn on in
sequence. After the LED will ash
red during this phase (about 1
minute): the hub is generating the
Wi-Fi hotspot
2.2 PROCEDURE FOR USING A HOTSPOT CONNECTION
STEP3*
To connect to this network, insert
the default password:
"12345678"
NOTE: when connected to this
network, connections to other
networks will be disabled and
access to the internet is
unavailable
STEP2*
The LED switch ON and remain
xed on green:
use your own device (e.g.: Smar-
tphone) and search available
networks for "Hub Smart Control",
the hotspot generated by the hub.
STEP4*
You are now connected to the
hotspot generated by the hub.
Next, type the default name of the
hub, "http://hub100.", in the
address bar of the browser on
your device.
STEP5
The user interface window will
open. Click on "menu".
STEP6
Click on "Congure network"
NOTE: this operation is not
necessary for usage, but it makes
the hub more secure and blocks
unwanted access to the system.
STEP7*
You will be requested to enter a
password; the default password
is: “1234”.
STEP8
Click on "congure network"
STEP9
The current setting will be
displayed; click on "edit"
Hub Smart Control
ENTER PASSWORD
12345678
Access
Type a website address
Conrm Cancel
Password
Enter password
http://hub100.
Edit
Hub hotspot
Save
menu
lampeggia rosso
Devices
Settings
CONFIGURE NETWORK
Congure network
Devices
Settings
Congure network
Congure system
1234 congure network
Congure network
Congure current network
Type of access : Hub hotspot
SSID : Hub Smart Control
Edit network
Select connection type
Hub hotspot
Wi-Fi network
Edit
STEP10
Click on "Hub hotspot"
STEP11
Fill in all elds with the connection data for the hotspot you wish to create.
Network name (SSID): the name of the hotspot generated by the hub.
See step 2 of this procedure (default: Hub Smart Control)
Current password: the existing password required to connect to the
hotspot used in step 3 of this procedure (default: 12345678)
New password: the new password which will be used in step 3.
It is recommended to set a new password for security reasons.
System name: the name to enter in the address bar of step 4 of this
procedure. The name cannot contain spaces.
NOTE: when entering the name in the address bar, it must always end with
a full stop (.)
EXAMPLE:
system name: “hubcasa”
address to enter: “http://hubcasa.”
ATTENTION:
To access the system with another device (mobile phone, PC, etc.) once
the system has been congured, simply follow step 14.
The IP address to connect to is visible on the congure network page in
the settings menu of a device which has already been congured
STEP12
After lling in all the elds, click on
"Save" at the bottom of the page.
STEP13
The hub will restart to activate the new settings;
the LED will ash red while creating the hotspot
(about 1 minute).
The personal device will disconnect from the hub’s
hotspot network.
STEP14
To use the system, reconnect to the hub’s Wi-Fi
network (steps 2, 3 and 4 of this procedure) using the
new data entered during step 11.
NOTE: it is recommended to create an icon on the
homepage of the personal device so you can quickly
access the commands; see paragraph 6.1
NOTE:
it is important to remember the infor-
mation entered as it is required in order
to use the hub with your own device
and to connect more devices at a later
time.
If the data are lost, the system must be
reset by following the procedure in
paragraph 7.1.
Edit network
Select connection type
Hub hotspot
Network wi
Hub hotspot conection
Network name (ssid)
Current password
New password
Conrm
password
System
System Name
Save
Network name (ssid)
Current password
New password
Conrm
password
System
System Name
Save
Wi-Fi Activated
CHOOSE A NETWORK...
Hub Smart Control
*NOTE: In steps 2, 3, 4 and 7 of
this procedure, the default
values to be used will be
suggested. If these were modi-
ed previously, the system must
be reset; see paragraph 7.1.

025-FIS18_Smart_GATEWAY 6
5 6
2.3 PROCEDURA PER L’UTILIZZO CON RETE WIFI ESISTENTE
Network wi
Save
Edit network
Select connection type
Hub hotspot
Network wi
STEP10
Click on "Wi-Fi network"
STEP11
A list of existing networks detected by the hub will appear.
Select the network you wish to connect the device to, and enter the
password used to access the existing network.
Configure a static IP address:
IP ADDRESS: the network address to be associated with the hub.
If you know an available address in your network, enter it.
If you do not know this parameter, try to connect using the suggested
default address, or see paragraph 6.2.
This address will then be used to connect to the user command interface;
see step 14.
ATTENTION:
To access the system with another device (mobile phone, PC, etc.) once
the system has been congured, simply follow step 14.
The IP address to connect to is visible on the congure network page in
the settings menu of a device which has already been congured; see
"URL" entry
STEP12
After lling in all the elds, click on
"Save" at the bottom of the page.
Edit network
Select connection type
Hub hotspot
Network wi
Available Wi-Fi networks
Password
SSID
Network1
Encryption
Static IP setting
IP adress
Net mask
Save
Save
Password
SSID
Network1
Encryption
STEP13
The hub will restart to activate the new settings,
and then connect to the existing Wi-Fi network.
The LED will ash blue during this phase (about 1
minute). After, will remain xed on blue.
The device will disconnect from the hub hotspot.
If the connection is unsuccessful see possible
causes below
POSSIBLE REASONS FOR FAILURE TO CONNECT TO AN EXISTING NETWORK
Check the values entered in step 11 of this procedure.
The following are the most likely causes:
- incorrect network password: verify you have entered the correct network access password
- incorrect IP address: an address already in use, or incorrect address, was entered. See paragraph 6.2
- network not found: verify the Wi-Fi network is available
Make a reset (see paragraph 7.1) and do again this procedure from step 2.
STEP14
To use the system:
- connect your device to the existing Wi-Fi network to
which the hub was connected
- open the browser and, in the address bar, type the
IP address which was saved in step 11
NOTE: it is recommended to create an icon on the
homepage of the personal device so you can quickly
access the commands; see paragraph 6.1
192.168.1.200
Static IP setting
IP adress 192.168.1.200
255.255.0.0
STEP1
Power ON the hub.
Red/green/blue lights turn on in
sequence. After the LED will ash
red during this phase (about 1
minute): the hub is generating the
Wi-Fi hotspot
STEP3*
To connect to this network, insert
the default password:
"12345678"
NOTE: when connected to this
network, connections to other
networks will be disabled and
access to the internet is
unavailable
STEP2*
The LED switch ON and remain
xed on green:
use your own device (e.g.: Smar-
tphone) and search available
networks for "Hub Smart Control",
the hotspot generated by the hub.
STEP4*
You are now connected to the
hotspot generated by the hub.
Next, type the default name of the
hub, "http://hub100.", in the
address bar of the browser on
your device.
STEP5
The user interface window will
open. Click on "menu".
STEP6
Click on "Congure network"
NOTE: this operation is not neces-
sary for usage, but it makes the
hub more secure and blocks
unwanted access to the system.
STEP7*
You will be requested to enter a
password; the default password
is: “1234”.
STEP8
Click on "congure network"
STEP9
The current setting will be
displayed; click on "edit"
Hub Smart Control
ENTER PASSWORD
12345678
Access
Type a website address
Conrm Cancel
Password
Enter password
http://hub100.
Edit
menu
lampeggia rosso
Devices
Settings
CONFIGURE NETWORK
Congure network
Devices
Settings
Congure network
Congure system
1234 congure network
Congure network
Congure current network
Type of access : Hub hotspot
SSID : Hub Smart Control
Edit
Wi-Fi Activated
CHOOSE A NETWORK...
Hub Smart Control
*NOTE: In steps 2, 3, 4 and 7 of
this procedure, the default
values to be used will be
suggested. If these were modi-
ed previously, the system must
be reset; see paragraph 7.1.

025-FIS18_Smart_GATEWAY 7
5 6
2.3 PROCEDURA PER L’UTILIZZO CON RETE WIFI ESISTENTE
Network wi
Save
Edit network
Select connection type
Hub hotspot
Network wi
STEP10
Click on "Wi-Fi network"
STEP11
A list of existing networks detected by the hub will appear.
Select the network you wish to connect the device to, and enter the
password used to access the existing network.
Configure a static IP address:
IP ADDRESS: the network address to be associated with the hub.
If you know an available address in your network, enter it.
If you do not know this parameter, try to connect using the suggested
default address, or see paragraph 6.2.
This address will then be used to connect to the user command interface;
see step 14.
ATTENTION:
To access the system with another device (mobile phone, PC, etc.) once
the system has been congured, simply follow step 14.
The IP address to connect to is visible on the congure network page in
the settings menu of a device which has already been congured; see
"URL" entry
STEP12
After lling in all the elds, click on
"Save" at the bottom of the page.
Edit network
Select connection type
Hub hotspot
Network wi
Available Wi-Fi networks
Password
SSID
Network1
Encryption
Static IP setting
IP adress
Net mask
Save
Save
Password
SSID
Network1
Encryption
STEP13
The hub will restart to activate the new settings,
and then connect to the existing Wi-Fi network.
The LED will ash blue during this phase (about 1
minute). After, will remain xed on blue.
The device will disconnect from the hub hotspot.
If the connection is unsuccessful see possible
causes below
POSSIBLE REASONS FOR FAILURE TO CONNECT TO AN EXISTING NETWORK
Check the values entered in step 11 of this procedure.
The following are the most likely causes:
- incorrect network password: verify you have entered the correct network access password
- incorrect IP address: an address already in use, or incorrect address, was entered. See paragraph 6.2
- network not found: verify the Wi-Fi network is available
Make a reset (see paragraph 7.1) and do again this procedure from step 2.
STEP14
To use the system:
- connect your device to the existing Wi-Fi network to
which the hub was connected
- open the browser and, in the address bar, type the
IP address which was saved in step 11
NOTE: it is recommended to create an icon on the
homepage of the personal device so you can quickly
access the commands; see paragraph 6.1
192.168.1.200
Static IP setting
IP adress 192.168.1.200
255.255.0.0
STEP1
Power ON the hub.
Red/green/blue lights turn on in
sequence. After the LED will ash
red during this phase (about 1
minute): the hub is generating the
Wi-Fi hotspot
STEP3*
To connect to this network, insert
the default password:
"12345678"
NOTE: when connected to this
network, connections to other
networks will be disabled and
access to the internet is
unavailable
STEP2*
The LED switch ON and remain
xed on green:
use your own device (e.g.: Smar-
tphone) and search available
networks for "Hub Smart Control",
the hotspot generated by the hub.
STEP4*
You are now connected to the
hotspot generated by the hub.
Next, type the default name of the
hub, "http://hub100.", in the
address bar of the browser on
your device.
STEP5
The user interface window will
open. Click on "menu".
STEP6
Click on "Congure network"
NOTE: this operation is not neces-
sary for usage, but it makes the
hub more secure and blocks
unwanted access to the system.
STEP7*
You will be requested to enter a
password; the default password
is: “1234”.
STEP8
Click on "congure network"
STEP9
The current setting will be
displayed; click on "edit"
Hub Smart Control
ENTER PASSWORD
12345678
Access
Type a website address
Conrm Cancel
Password
Enter password
http://hub100.
Edit
menu
lampeggia rosso
Devices
Settings
CONFIGURE NETWORK
Congure network
Devices
Settings
Congure network
Congure system
1234 congure network
Congure network
Congure current network
Type of access : Hub hotspot
SSID : Hub Smart Control
Edit
Wi-Fi Activated
CHOOSE A NETWORK...
Hub Smart Control
*NOTE: In steps 2, 3, 4 and 7 of
this procedure, the default
values to be used will be
suggested. If these were modi-
ed previously, the system must
be reset; see paragraph 7.1.

025-FIS18_Smart_GATEWAY 8
7 8
NOTE
In step 4 of the procedure, the default values to be used will be suggested. If these were modied previously and
cannot be recovered, the system must be reset; see paragraph 7.1.
A reset will not delete systems created in the interface (see paragraph 3); it will only reset the network settings
(network name, page address, password).
The default password from "step 4" can be changed by accessing "menu-settings-change password".
3.1 INTRODUCTION
After the procedure in paragraph 2 is complete, the personal device is able to communicate with the hub.
The following step creates the various user command interfaces which will appear on the home screen of the application.
These interfaces can be either devices or groups.
Devices: the term device refers to an interface which is used to drive a load (e.g.: light or roller shutters)
Groups: the term ‘groups’ refers to an interface which is used to drive a set of previously created devices. This is useful for
creating a "switch OFF all lights" command or "lower all roller shutters" command.
To create devices, see paragraphs 3.2 and 3.3; to create groups, see paragraphs 3.3 and 3.4.
NOTE: both devices and groups will appear on the homepage. It is recommended to use the name which is assigned to
each interface to distinguish group commands from commands for a single device
3.2a CREATING A DEVICE
3 - SYSTEM CONFIGURATION
STEP2
Click on "menu".
STEP1
Access the application according
to the network conguration
performed in paragraph 2
STEP6
A list of created devices will
appear (the default list has no
devices).
Click on the "+" button to add
devices
STEP5
Click on "list of devices"
menu
Devices
Congure system
LIST OF DEVICES
LIST OF GROUPS
RESET
STEP3
Click on "Congure system"
Congure system
Devices
Settings
Congure network
Congure system
STEP4*
You will be requested to enter a
password; the default
password is: “1234”.
Conrm Cancel
Password
Enter password
Saving device
Deviced saved
1234
list of devices
+
List of Devices
STEP8
Click on "save" at the bottom of
the page.
STEP9
The application displays the list
of updated devices. If you wish
to add more devices,
return to step 2 of this procedu-
re.
If all user command interfaces
have been created, go to step
3.2b to associate them with the
central receivers.
STEP7
The elds to ll in to create the device will appear:
NAME: the name which will appear on the homepage
TYPE OF COMMAND: determines the user command interface and, therefore, the actions which can be perfor-
med. This eld is chosen according to the receiver to be controlled. See the table below
ICON: the graphic icon which appears to the side of the device; for graphic purposes only
Congure system
Save
Name
Type of
command
Icon
TYPE OF COMMAND
On-Off
Open-Stop-Close
Impulse
Dimmer light
RGB/RGBW light
Tunable white light
EXECUTABLE ACTIONS
On - Off
Open - Stop - Close
Impulse
On - Off - Intensity setting
On - Off - Intensity setting - Colour management
On - Off - Intensity setting - Tunable light management

025-FIS18_Smart_GATEWAY 9
7 8
NOTE
In step 4 of the procedure, the default values to be used will be suggested. If these were modied previously and
cannot be recovered, the system must be reset; see paragraph 7.1.
A reset will not delete systems created in the interface (see paragraph 3); it will only reset the network settings
(network name, page address, password).
The default password from "step 4" can be changed by accessing "menu-settings-change password".
3.1 INTRODUCTION
After the procedure in paragraph 2 is complete, the personal device is able to communicate with the hub.
The following step creates the various user command interfaces which will appear on the home screen of the application.
These interfaces can be either devices or groups.
Devices: the term device refers to an interface which is used to drive a load (e.g.: light or roller shutters)
Groups: the term ‘groups’ refers to an interface which is used to drive a set of previously created devices. This is useful for
creating a "switch OFF all lights" command or "lower all roller shutters" command.
To create devices, see paragraphs 3.2 and 3.3; to create groups, see paragraphs 3.3 and 3.4.
NOTE: both devices and groups will appear on the homepage. It is recommended to use the name which is assigned to
each interface to distinguish group commands from commands for a single device
3.2a CREATING A DEVICE
3 - SYSTEM CONFIGURATION
STEP2
Click on "menu".
STEP1
Access the application according
to the network conguration
performed in paragraph 2
STEP6
A list of created devices will
appear (the default list has no
devices).
Click on the "+" button to add
devices
STEP5
Click on "list of devices"
menu
Devices
Congure system
LIST OF DEVICES
LIST OF GROUPS
RESET
STEP3
Click on "Congure system"
Congure system
Devices
Settings
Congure network
Congure system
STEP4*
You will be requested to enter a
password; the default
password is: “1234”.
Conrm Cancel
Password
Enter password
Saving device
Deviced saved
1234
list of devices
+
List of Devices
STEP8
Click on "save" at the bottom of
the page.
STEP9
The application displays the list
of updated devices. If you wish
to add more devices,
return to step 2 of this procedu-
re.
If all user command interfaces
have been created, go to step
3.2b to associate them with the
central receivers.
STEP7
The elds to ll in to create the device will appear:
NAME: the name which will appear on the homepage
TYPE OF COMMAND: determines the user command interface and, therefore, the actions which can be perfor-
med. This eld is chosen according to the receiver to be controlled. See the table below
ICON: the graphic icon which appears to the side of the device; for graphic purposes only
Congure system
Save
Name
Type of
command
Icon
TYPE OF COMMAND
On-Off
Open-Stop-Close
Impulse
Dimmer light
RGB/RGBW light
Tunable white light
EXECUTABLE ACTIONS
On - Off
Open - Stop - Close
Impulse
On - Off - Intensity setting
On - Off - Intensity setting - Colour management
On - Off - Intensity setting - Tunable light management

025-FIS18_Smart_GATEWAY 10
9 10
3.2b ASSOCIATING THE DEVICE WITH THE RECEIVER
After the procedure in paragraph 3.2a is complete, the various devices which have been created will be displayed on the
homepage of the application.
The next step is to associate each device with the receiver to be driven.
The receiver must be accessed to complete this step.
PROCEDURE
3.3 DELETING OR MODIFYING A CREATED DEVICE
If you wish to delete or modify a created device, change the name, icon or the type of command, perform the following
procedure:
STEP2
Click on "menu".
STEP1
Access the application according
to the network conguration
performed in paragraph 2
STEP6
A list of created devices will
appear.
Select the device to be modied
STEP5
Premere su “lista dispositivi”
menu
Devices
Congure system
LIST OF DEVICES
LIST OF GROUPS
RESET
STEP3
Click on "Congure system"
Congure system
Devices
Settings
Congure network
Congure system
STEP4*
You will be requested to enter a
password; the default
password is: “1234”.
Conrm Cancel
Password
Enter password
1234
list of devices
List of devices
STEP7
Click on "edit” to change the
settings or "delete" to remove it
Device 1
List of devices
Device 1
Edit Delete
ATTENTION
In step 4 of the procedure, the default values to be used will be suggested.
If these were modied previously and cannot be recovered, the system must
be reset; see paragraph 7.1.
A reset will not delete systems created in the interface (see paragraph 3);
it will only reset the network settings (network name, page address,
password).
The default password from "step 4" can be changed by accessing
"menu-settings-change password"
STEP2
While programming the radio, you will be requested to transmit a command. To transmit the command, select the
device on the homepage and transmit any command using the keys available.
The receiver ashes three times to conrm programming was successful.
STEP1
Access the receiver and perform the radio programming procedure for the multifunction radio transmitters.
See receiver manual.
Make a short
press of
the button
Make a short press
of the button related to
the output which the
transmitter wants
to be programmed.
THE LED TURNS ON
SMART1
SMART1
SMART4
SMART4
THE LED TURNS ON
LED MAKES 3 FLASHES
AND TURNS OFF
LED MAKES 3 FLASHES
AND TURNS OFF
SELECT THE DEVICE ON THE HOMEPAGE AND TRANSMIT
ANY COMMAND USING THE KEYS AVAILABLE