Articona 833158 User manual

Trademarks
Contents subject to revision without prior notice. All
trademarks remain the property of their owners.
Copyright Statement
This publication may not be reproduced as a whole or
in part, in any way whatsoever unless prior consent
has been obtained from the owner.
FCC Warning
This Media Converter has been tested and found to
comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These
standards are designed to provide reasonable
protection against harmful interference when this
device is operated in a commercial environment. This
device generates, uses, and can radiate radio
frequency energy and may cause harmful
interference to radio communications unless installed
in accordance with this User’s Guide. Operation of
this device in a residential area is likely to cause
harmful interference which will make the user
responsible for the appropriate remedial action at his
/ her own expense.
CE Mark Warning
This is a Class A product. In a domestic environment
this product may cause radio interference in which
case the user will need to consider adequate
preventative methods.
1. Checklist
The package should contain the following items:
-
The Media Converter
-
AC-DC Power Adapter
-
User’s Guide
Please notify your sales representative immediately if
any item is missing or damaged.
2. Overview
This Media Converter is designed to meet the
massive needs for Gigabit network deployment and
able to extend a copper based Gigabit network via
fiber cable. It is fully compliant with IEEE802.3,
802.3u, 802.3ab and 802.3z standards. It can be
installed into a 16-Slot Universal Media Converter
Rack. The installation and operation procedures are
simple and straightforward. Operation status can be
locally monitored through a set of Diagnostic LED
indicators located in the front panel.
Major Features:
-
TP and Fiber Auto-Negotiation
-
MDI/MDIX Auto-Crossover
-
Flow Control and Back Pressure
-
9K bytes Jumbo Frame
-
Store and Forward switching mechanism
-
1K MAC address
-
Link Alarm
-
100/1000Mbps dual rate fiber uplink
3. Installation
-
Attach fiber cable from the Media Converter to the
fiber network. The fiber connections must be
matched –transmit socket to receive socket.
-
Attach a UTP cable from the 10/100/1000BASE-T
network to the RJ-45 port on the Media Converter.
-
Connect the power adapter to the Media Converter
and check that the Power LED lights up. The TX
Link/Act and F/O Link/Act LEDs will light up when
all the cable connections are satisfactory.
Fig 1. Front Panel of the Media Converter
Fig 2. Rear Panel of the Media Converter

4. DIP SWITCH Setting
The default setting for PIN 1 and 6 is ON. The rest
pins are OFF.
Pin NO.
Function
OFF
ON
1
TP Auto-Negotiation
Disable
Enable
2
Manual TP speed
10M
100M
3
Manual TP speed
N/A
1000M
4
Duplex mode
Half
Full
5
Flow Control
Disable
Enable
6
F/O mode
Force
Auto
7
Link Alarm
Disable
Enable
8
Reserved
-
-
NOTE:
Before changing TP speed, duplex mode and flow
control setting, please make sure PIN 1 is set to OFF.
When TP speed is set to 10M or 100M manually, PIN 3
needs to be turned OFF.
Under 1000Mbps, it supports full-duplex mode only.
5. LED Description
6. Technical Specifications
Fiber Transceiver Information
100M/1000M Dual Speed
LED
Color
Function
Power
Green
Power is available.
TX
Link/Act
Green
TX cable connection with remote
device is good.
Blinking
TX traffic is present.
FO
Link/Act
Green
F/O works in 100M.
Orange
F/O works in 1000M.
Blinking
F/O traffic is present.
FDX
OFF
TX works in Half-Duplex.
Green
TX works in Full-Duplex.
Speed
OFF
TX works in 10M.
Green
TX works in 100M.
Orange
TX works in 1000M.
Status
Green
TX and F/O link is up.
Orange
TX or F/O link is down.
Standards
IEEE 802.3, 802.3u, 802.3ab, 802.3z
Interface
1 X 10/100/1000 RJ-45 connector
1 X 100/1000 F/O port or SFP slot
LED
Power, FDX, Status, Speed,
FO Link/ACT, TX Link/ACT
Power
I/P: AC100-240V; O/P: DC5V, 2A
Power Consumption
2.2W
Shipping Weight
0.6KG
Dimensions
71mm(W)X94mm(D)X26mm(H)
Temperature
Operating: 0o~50oC; Storage: -20o~60oC
Humidity
5%~90% RH
Certification
FCC/CE Class A
Media
TP:
EIA/TIA-568 CAT 5e, 1000M
Fiber
9/125, 10/125um single-mode fiber
*Please contact us for further reports and updates.

10/100/1000BASE-T to
100/1000BASE-X Standalone
Gigabit Media Converter
User’s Guide
Version 1.1
Articona International BV
Withuisveld 30
6226 NV Maastricht
Netherlands
[e-mail]