Inforesight Solaira Cosy XL 277V Double User manual

C = COLOR CODE
WEATHERPROOF INFRARED HEATERS SUITABLE FOR OUTDOOR AND INDOOR USE
IN NON-HAZARDOUS AREAS
- COMMERCIAL AND INDUSTRIAL, (RESIDENTIAL 240V OUTDOOR USE ONLY)
Reference Manual
Solaira Cosy XL
277V Double
EN
Stainless Steel Frontage/Fascia
Standard Frontage/Fascia
STANDARD FRONTAGE FASCIA HEATER MODELS FOR CANADA & USA:
STAINLESS STEEL FRONTAGE FASCIA HEATER MODELS FOR CANADA & USA:
Ref No. 043499-3-EN-S (Iss. Oa)
I M P O R TA N T - S AV E T H E S E I N S T R U C T I O N S F O R F U T U R E R E F E R E N C E
247748
INFORESIGH CONSUMER PRODUC S INC.
125 Traders Blvd. E Unit # 4, Mississauga, Ontario L4Z 2 3
Tel: [phone] - Fax: [phone]
Email: [e-mail] - Website: www.solairaheaters.com
SCOSYXL30277SS-C (240V - 2 × 1125W [2250W TOTAL] 277V - 2 × 1500W [3000W TOTAL])
SCOSYXL30277SSLL-C (240V - 2 × 1125W [2250W TOTAL] 277V - 2 × 1500W [3000W TOTAL]) LOW LIGHT CANDEL
SCOSYXL40277SS-C (240V - 2 × 1500W [3000W TOTAL] 277V - 2 × 2000W [4000W TOTAL])
SCOSYXL40277SSLL-C (240V - 2 × 1500W [3000W TOTAL] 277V - 2 × 2000W [4000W TOTAL]) LOW LIGHT CANDEL
C = COLOR CODE
SCOSYXL30277-C (240V - 2 × 1125W [2250W TOTAL] 277V - 2 × 1500W [3000W TOTAL])
SCOSYXL30277LL-C (240V - 2 × 1125W [2250W TOTAL] 277V - 2 × 1500W [3000W TOTAL]) LOW LIGHT CANDEL
SCOSYXL40277-C (240V - 2 × 1500W [3000W TOTAL]) 277V - 2 × 2000W [4000W TOTAL])
SCOSYXL40277LL-C (240V - 2 × 1500W [3000W TOTAL]) 277V - 2 × 2000W [4000W TOTAL]) LOW LIGHT CANDEL

I M P O R TA N T I N S T R U C T I O N S
When using electrical short-wave INFRARED EATERS, basic
precautions should always be followed to reduce the risk of fire,
electric shock, and injury to persons, including the following:
2 of 12 Ref No. 043499-3-EN-S (Iss. Oa)
1. Read all instructions before using this heater.
2. Use this heater only as described in this manual. Any other use not
recommended by the manufacturer may cause fire, electric shock, or
injury to persons.
3. This heater is hot when in use. To avoid burns, do not let bare skin
touch hot surfaces. If provided, use handles when moving this heater.
Keep combustible materials, such as furniture, pillows, bedding,
papers, clothes, and curtains at least 6 feet (1.8m) from the front of the
heater and keep them away from the sides and rear.
4. Extreme caution is necessary when any heater is used by or near
children or invalids and whenever the heater is left operating and
unattended.
5. When not in use, disconnect the supply.
6. Do not operate any heater with a damaged cord or after the heater
malfunctions, has been dropped or damaged in any manner. Return
heater to authorized service facility for examination, electrical or
mechanical adjustment, or repair.
7. This heater is not intended for use in bathrooms, laundry areas and
similar locations. Never locate heater where it may fall into a bathtub
or other water container.
8. Do not run cord under carpeting. Do not cover cord with throw rugs,
runners, or the like. Arrange cord away from traffic area and where it
will not be tripped over.

9. To disconnect heater, turn controls to off.
WARNING -
Each power supply circuit shall be provided with
disconnecting means and the disconnecting means shall be grouped
together.
10. Do not insert or allow foreign objects to enter any opening as this may
cause an electric shock or fire, or damage the heater.
11. To prevent a possible fire, do not block openings in any manner.
12. A heater has hot parts inside. Do not use it in areas where gasoline,
paint, or flammable liquids are used or stored.
13. Do not cover or otherwise obstruct the heater.
14. Do not touch the heater during operation as the body becomes
very hot and cause burns. Particular attention has been given
where children and vulnerable people are present.
S AV E T H E S E I N S T R U C T I O N S
I M P O R TA N T I N S T R U C T I O N S
3 of 12 Ref No. 043499-3-EN-S (Iss. Oa)
G R O U N D I N G I N S T R U C T I O N S
The 240V / 277V heaters have 2 × cords from the junction boxes which
must be permanently connected to a properly grounded supply.
Kee combustible material such as furniture, a ers, clothes and
curtains at least 6 feet (1.8m) from the front of the heater and away
from the sides and rear.
Heaters are not intended for use as indoor residential or as a
household heater. They may be used for outdoor residential 240V use.
W A R N I N G : R I S K O F F I R E

Before using this appliance:
1. Check that the voltage indicated on the units rating label corresponds to the mains
supply voltage.
2. Do not install the heaters less than the minimum height from the floor as specified below
in the specification tables.
3. Ensure that the heater has been securely fastened in its final mounting position.
4. WARNING - This appliance must be grounded and hard wired!
5. WARNING - Keep the supply cables away from the front and body of the heater which
will get hot during use.
6. Do not cover or obstruct the heater while it is in use.
7. Do not insert any object through any slot or opening in the heater.
8. Do not use if a grille is not present.
9. WARNING - Before replacing the lamp emitter or cleaning the unit, ensure that the hard
wired circuit is disconnected from the mains supply. Note: always ensure that the lamp
emitters are cool before handling.
10. Do not handle a lamp emitter with bare hands. If it is inadvertently touched,
remove finger marks with a soft cloth and methylated spirit or rubbing
alcohol. Otherwise, the marks will burn into the lamp emitter during use
causing premature heater failure.
11. The heater is not intended for use by young children and must be supervised
by a responsible person at all times.
I N T R O D U C T I O N
The Solaira Cosy XL 277V Double heater produces short-wave infrared heat like the sun,
warming people and objects and not the air in between. It is mounted on an adjustable
bracket that allows the heat to be directed exactly where it is required. Its attractive, light-
weight design means that it is effective yet unobtrusive. The short-wave infrared weatherproof
heater is designed for indoor and outdoor use.
Please read the following instructions carefully before use. The safety of this heater is
guaranteed only by its correct usage in accordance with these instructions, therefore
they should be retained for future reference.
C AU T I O N
4 of 12 Ref No. 043499-3-EN-S (Iss. Oa)

S P E C I F I C AT I O N TAB L E - 2 4 0 V / 2 7 7 V H E ATE R S
5 of 12 Ref No. 043499-3-EN-S (Iss. Oa)
I N S TAL L AT I O N
The 240V / 277V heaters are fitted with a 2 × supply cords measuring 79 inches (200cm)
each for permanent connection.
WARNING: Wiring procedures and connections should be in accordance with the
National Electric Code (NEC) and local codes.
WARNING: If a supply cord becomes damaged, it must be immediately replaced by a
qualified person in order to avoid a hazard.
CAUTION: Disconnect electric power supply before working on circuit wiring to prevent
electric shock.
CAUTION:
Please observe the minimum safe distance between the heater body and any
inflammable surfaces.
CAUTION: When the electrical connection is outside a weatherproof socket must be used
having ground fault protection (GFCI or GFI).
NOTE: CONSULT A QUALIFIED ELECTRICIAN, IF IN DOUBT.
!
Model Ty es
SCOSYXL30277-C &
SCOSYXL30277LL-C,
SCOSYXL30277SS-C &
SCOSYXL30277SSLL-C
SCOSYXL40277-C &
SCOSYXL40277LL-C
SCOSYXL40277SS-C
SCOSYXL40277SSLL-C
Voltage 240V / 277V
No. of Emitters × Power 2 × 1125W / 1500W 2 × 1500W / 2000W
Current er Emitter 4.7A / 5.4A 6.3A / 7.2A
Total Power of Unit 2250W / 3000W 3000W / 4000W
Total Current of Unit 9.4A / 10.8A 12.5A / 14.4A
Min. mounting height from floor 7ft 10½in (240cm)
Min. distance from ceiling 8¾in (22cm)
Min. distance from side wall 17in (43cm)
17in (43cm) /
25in (64cm)
Dimensions - W × H × D 50in × 4½in × 3½in (127cm × 11cm × 9cm),
48in × 4½in × 3½in (122cm × 11cm × 9cm)
Weight 13.2lbs (6.0kg)

6 of 12 Ref No. 043499-3-EN-S (Iss. Oa)
The Solaira Cosy XL 277V Double heater should be mounted
in a horizontal (Fig. A) manner only.
1. Securely fasten the heater brackets to the mounting surface
using the fixing holes in the brackets. See Fig. C for mounting
hole centers of the brackets. Please refer to the specification
table for recommended positioning of the heater.
2. The heater bracket can be used to adjust the direction of the
heater up and down (see Fig. B). This is done by loosening the
bolts fixing the heater to the bracket, and then retightening
once the correct position is achieved. Fix in the required
angular position.
3. Secure the supply cords so they are directed away from the
heater and is not resting on the body or obstructing the
air-vents.
ORIZONTAL MOUNTING
Fig.
Fig. B
Fig. C
MIN. 45°
98 in (250 cm)
GROUND LEVEL
INDENT
PREVENTS
DROP
DOWN
MOVEMENT
C A U T I O N
M O U N T I N G
Always isolate the heater from the mains su ly
when mounting or adjusting the heater osition.
CAUTION: When mounting the heater, do not position the heater at an angle more than 50° or
less then 45° as shown in Fig. A.
CAUTION: The heater should be mounted with the minimum clearances adhered to. Please refer
to the specification table for the recommended positioning of the heater. Do not install the heater
in a corner!
CAUTION: Always allow the heater to cool before attempting to reposition/move. Never attempt
to move the heater while it is switched on!
CAUTION: Observe the minimum safe distance between the heater body and inflammable
surfaces and objects when mounting (see specification table).
MA . 50°

7 of 12 Ref No. 043499-3-EN-S (Iss. Oa)
M O U N T I N G TO A C E I L I N G / O V E R H AN G
C AU T I O N
Always isolate the heater from the mains su ly when mounting or adjusting the
heater osition.
The Solaira Cosy XL 277V Double heater can be mounted to a ceiling or overhang (as shown in
Fig. D) using 2 × optional ceiling brackets (not supplied).
1. Securely fasten the heater brackets to the mounting surface using the fixing holes in the
brackets. See Fig. F for mounting hole centers of the brackets. Please refer to the
specification table for the recommended positioning of the heater.
2. Mount the heater to the brackets as shown in Fig. E and fix in the position by tightening the
fixing bolt on the bracket at the rear of the heater.
3. Secure the supply cables so the cables are directed away from the heater and is not
resting on the body or obstructing the air-vents.
Fig. D
Fig. E Fig. F
CAUTION: The heater should be mounted with the minimum clearances adhered to.
Please refer to the specification table for the recommended positioning of the heater. Do
not install the heater in a corner!
CAUTION: The heater should always be angled downwards when mounting this way
CAUTION: Always allow the heater to cool before attempting to reposition/move. Never
attempt to move the heater while it is switched on!
CAUTION:
Observe the minimum safe distance between the heater front and
inflammable surfaces and objects when mounting.
8¾”
[22cm]
MIN.
REFER TO
TABLE 1
FOR MIN.
DISTANCE
TO SIDE WALL

8 of 12 Ref No. 043499-3-EN-S (Iss. Oa)
C I R C U I T D I AG R AM
Fig. G
Represents cables
pre-wired to
heater
(colors as shown)
Appropriately
rated double pole
switches or double
pole breakers
grouped together
M A I N T E N AN C E
CAUTION: Always isolate the mains power from the heater or heater assembly before replacing
lamp emitters or any maintenance procedure including cleaning.
CAUTION: Should dust or dirt appear on the reflectors, it is recommended that that the grilles
and lamp emitters are removed and the reflectors are wiped with a lint-
free cloth before
reassembling (see lamp emitter replacement instructions).
NOTE: For re lacement lam emitters or s are arts (see diagrams on next age) lease
contact your local distributor quoting model ty e and rating from rating label. It is very
im ortant that your re lacement lam emitter is exactly the same as the one it was
su lied with. Failure to fit the exact same ty e can cause the heater to rematurely fail.
!
CAUTION: Please ensure that the length of wires on the replacement lamp emitter are the same
as shown in the diagram below (Fig. ).
Y O U R R E P L A C E M E N T L AM P E M I T T E R
Fig. H
240V / 277V ~ 60 z

9 of 12 Ref No. 043499-3-EN-S (Iss. Oa)
C O S Y X L D O U B L E S TA N D A R D - C O M P O N E N T PA R T D I A G R A M
Fig. I
C O S Y X L D O U B L E S TA I N L E S S S T E E L - C O M P O N E N T PA R T
D I A G R A M
Fig. J

10 of 12 Ref No. 043499-3-EN-S (Iss. Oa)
1. Ensure the heater and lamp emitters are cool and the power supply is disconnected
before disassembly.
2. Remove the heater from its mounted position should it not be safe to work on it while
mounted.
3. Remove the screws from the junction box (Fig. K) and lift off the cover to the box in which
the lamp emitter will be replaced.
C A U T I O N
Disconnect from the mains ower su ly before any attem ts are made to re lace a lam
emitter. Contact your distributor for the correct re lacement quoting model ty e and rating
from the rating label. We recommend you read through the rocedure and refer to the arts
diagram on the revious age of this manual before commencing work.
R E P L A C I N G A L A M P E M I T T E R
4. Disconnect the lamp emitter wires from the connector blocks by unscrewing the screws
highlighted above in Fig. L.
5. Unscrew the four screws (see Fig. M) from the end cover and remove from the heater
body. Repeat at opposite end.
6. Slide out the side covers from both ends and slide out the guard from either end as shown
in Fig. N.
Fig. M Fig. N
Fig. K Fig. L
CABLE STRAIN RELIEF
BRIDGE (MAX. TIGHTEN)
WEATHERPROOF GLAND
ASSEMBLY (SILICONE
WASHER/GLAND NUT)

11 of 12 Ref No. 043499-3-EN-S (Iss. Oa)
8. Remove the two screws as highlighted on in Fig. P to take out the side reflector bracket
and reflector assembly that allows access the lamp emitter holding clip. Repeat at opposite
end of the lamp emitter.
9. Where the lamp emitter wires are fed through the gasket into the junction box (Fig. P),
gently pull the lamp emitter wires through the body of the heater so the wires exit the
junction box.
10. At the opposite end of the lamp emitter, the wire will be clearly visible in the lamp emitter
wire tube so gently pull the long wire (Fig. Q) out of the tube until it is free.
11. One at a time pull the spring clips back in the direction shown in Fig. R and lift up the
ceramic caps of the lamp emitter to remove it from the heater.
12. The lamp emitter should now be removed from the heater. Refit the new lamp emitter in
reverse order ensuring the ceramic caps are correctly seated in the lamp emitter holders, no
wires are trapped and all screws are fully tightened.
Fig. Q Fig. R
Fig. P

IMPORTANT - SAVE THESE
INSTRUCTIONS FOR FUTURE REFERENCE
INFORESIGH CONSUMER PRODUC S INC.
125 Traders Blvd. E Unit # 4, Mississauga, Ontario L4Z 2 3
Tel: [phone] - Fax: [phone] - Email: [e-mail] - Website: www.solairaheaters.com
Due to our policy of ongoing improvement, we reserve the right to make changes without notice.
© 2023 INFORESIG T CONSUMER PRODUCTS INC.
Ref No. 043499-EN-S Issue No. Oa
Solaira Cosy XL
277V Double
247748
Stainless Steel Frontage/Fascia
Standard Frontage/Fascia
STANDARD FRONTAGE FASCIA HEATER MODELS FOR CANADA & USA:
STAINLESS STEEL FRONTAGE FASCIA HEATER MODELS FOR CANADA & USA:
C = COLOR CODE
SCOSYXL30277SS-C (240V - 2 × 1125W [2250W TOTAL] 277V - 2 × 1500W [3000W TOTAL])
SCOSYXL30277SSLL-C (240V - 2 × 1125W [2250W TOTAL] 277V - 2 × 1500W [3000W TOTAL]) LOW LIGHT CANDEL
SCOSYXL40277SS-C (240V - 2 × 1500W [3000W TOTAL] 277V - 2 × 2000W [4000W TOTAL])
SCOSYXL40277SSLL-C (240V - 2 × 1500W [3000W TOTAL] 277V - 2 × 2000W [4000W TOTAL]) LOW LIGHT CANDEL
C = COLOR CODE
SCOSYXL30277-C (240V - 2 × 1125W [2250W TOTAL] 277V - 2 × 1500W [3000W TOTAL])
SCOSYXL30277LL-C (240V - 2 × 1125W [2250W TOTAL] 277V - 2 × 1500W [3000W TOTAL]) LOW LIGHT CANDEL
SCOSYXL40277-C (240V - 2 × 1500W [3000W TOTAL]) 277V - 2 × 2000W [4000W TOTAL])
SCOSYXL40277LL-C (240V - 2 × 1500W [3000W TOTAL]) 277V - 2 × 2000W [4000W TOTAL]) LOW LIGHT CANDEL