ASCO POWER TECHNOLOGIES 159 User manual

Surge Protective Devices Installation & Operation Manual
Model 159

© 2020 ASCO Power Technologies. All Rights Reserved
2
IO-75024
01/2020
For access to self-service tools and chat support visit se.com/us/en/work/support or call 1-888-778-2733 for technical assistance
Model 159 (Edco HVCP-48)
Surge Protective Device (SPD)
Safety Information
Important Information
Read these instructions carefully and look at the equipment to become
familiar with the device before trying to install, operate, service or maintain it.
The following special messages may appear throughout thisbulletin or on the
equipment to warn of potential hazards or to call attention to information that
clarifies or simplifies a procedure.
The addition of either symbol to a “Danger”or “Warning” safety label
indicates that an electrical hazard exists which will result inpersonal
injury if the instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messagesthat follow this
symbol to avoid possible injury or death.
DANGER
DANGER indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING
WARNING indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided,
could result in minor or moderateinjury.
NOTICE
NOTICE is used to address practices not related to physical injury. The safety
alert symbol shall not be used with this signal word.
Please Note
Electrical equipment should be installed, operated, serviced, and maintained only
by qualified personnel. No responsibility is assumed by ASCO Power Technologies
for any consequences arising out of the use of this material.
A qualified person is one who has skills and knowledge related to the
construction, installation, and operation of electrical equipment andhas received
safety training to recognize and avoid the hazards involved.

© 2020 ASCO Power Technologies. All Rights Reserved 3
IO-75024
01/2020
For access to self-service tools and chat support visit se.com/us/en/work/support or call 1-888-778-2733 for technical assistance
Model 159 (Edco HVCP-48)
Surge Protective Device (SPD)
Introduction The ASCO Model 159 is a hybrid surge protective device product featuring
DC power, data and video protection in one package. Each separate circuit
is capable of handling high-current impulses while tightly clamping transients
and allowing critical power and data to be transmitted.
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
• Apply appropriate personal protective equipment (PPE) and follow safe
electrical work practices. See NFPA 70E, NOM-029-STPS or CSA Z462.
• This equipment must only be installed and serviced by qualied electri-
cal personnel.
• Turn o󰀨 all power supplying this equipment before working on or inside
equipment.
• Always use a properly rated voltage sensing device to conrm power is o󰀨.
• Replace all devices, doors and covers before turning on power to this
equipment.
• This equipment must be e󰀨ectively grounded per all applicable codes.
Use an equipment-grounding conductor to connect this equipment to the
power system ground.
• Conrm that the Surge Protective Device voltage rating on the module
or nameplate label is not less than the operating voltage.
• Do not exceed the following current levels:
– DC Power Circuit - 1 Amp
– High Speed Data Circuit - 150mA
Failure to follow these instructions will result in death or serious injury.
WARNING: This product can expose you to chemicals including
DINP, which is known to the State of California to cause cancer, and
DIDP which is known to the State of California to cause birth defects
or other reproductive harm. For more information go to: www.
P65Warnings.ca.gov.
NOTICE
LOSS OF SURGE SUPPRESSION
• Make certain that Surge Protective Device is disconnected from the
circuit it is protecting before conducting high potential insulation testing.
Failure to follow these instructions can result in equipment damage.
DANGER

© 2020 ASCO Power Technologies. All Rights Reserved
4
IO-75024
01/2020
For access to self-service tools and chat support visit se.com/us/en/work/support or call 1-888-778-2733 for technical assistance
Model 159
Installation 1. Turn o󰀨 all power supplying this equipment before working on or inside-
equipment.
2. Mount device as close to protected equipment as possible using mount-
ing anges (hardware not supplied).
3. Strip all wires going to the eld and protected terminal plugs on the
device 0.28 - 0.31 inches.
4. Connect power wire from eld side to the eld side terminal on device
marked “VS+” and “GND” for the ground.
5. Connect data wiring from eld to the eld side of device marked
“SDIO+” and “SDIO-”.
6. Connect video wire from eld to the eld side of device marked “Video+”
and “Video-”.
7. Connect protected equipment wiring to all corresponding terminal on the
protected side of the device.
8. Replace the barrier, cover/door and/or trim to the equipment.
9. Equipment may be re-energized after all the above steps are complete.
Figure 1: Wiring Diagram
Model 159 (Edco HVCP-48)
Surge Protective Device (SPD)

© 2020 ASCO Power Technologies. All Rights Reserved 5
IO-75024
01/2020
For access to self-service tools and chat support visit se.com/us/en/work/support or call 1-888-778-2733 for technical assistance
Dimensions (in. / mm.)
Model 159 (Edco HVCP-48)
Surge Protective Device (SPD)
159D070S10KAN6N0
(Edco HVCP-48)
159D070S10KAN6N0
(Edco HVCP-48-BNC)
SDIO SDIO GND VS
FIELD
PROTECTED
GND
- + +
Chassis
- + +
SDIO SDIO GND VS
OUT
VIDEO
IN
VIDEO
HVCP-48-BNC
DATA-15V
VIDEO-2V
WKYR R
Made in Mexico
DC-68V UL
Breakdown:
Voltage
LISTED
4S37
ISOLATED LOOP
CIRCUIT PROTECTOR
ASCO®
SDIO SDIO GND VS
FIELD
PROTECTED
GND
- + +
Chassis
- + +
SDIO SDIO GND VS
OUT
VIDEO
IN
VIDEO
HVCP-48-BNC
DATA-15V
VIDEO-2V
WKYR R
Made in Mexico
DC-68V UL
Breakdown:
Voltage
LISTED
4S37
ISOLATED LOOP
CIRCUIT PROTECTOR
ASCO®
SDIO SDIO GND VS
FIELD
PROTECTED
GND
- + +
Chassis
- + +
SDIO SDIO GND VS
OUT
VIDEO
IN
VIDEO
HVCP-48-BNC
DATA-15V
VIDEO-2V
WKYR R
Made in Mexico
DC-68V UL
Breakdown:
Voltage
LISTED
4S37
ISOLATED LOOP
CIRCUIT PROTECTOR
ASCO®
FIELD
PROTECTED
SDIO SDIO VIDEO VIDEO GND VS
- + - + +
BLU
WHT
GRN
WHT
BLK
ORN or BRN
RED
BLU
GRN
RED
ORN or BRN
BLK
- + - + +
SDIO SDIO VIDEO VIDEO GND VS
ASCO®
FIELD
PROTECTED
SDIO SDIO VIDEO VIDEO GND VS
- + - + +
BLU
WHT
GRN
WHT
BLK
ORN or BRN
RED
BLU
GRN
RED
ORN or BRN
BLK
- + - + +
SDIO SDIO VIDEO VIDEO GND VS
ASCO®
FIELD
PROTECTED
SDIO SDIO VIDEO VIDEO GND VS
- + - + +
BLU
WHT
GRN
WHT
BLK
ORN or BRN
RED
BLU
GRN
RED
ORN or BRN
BLK
- + - + +
SDIO SDIO VIDEO VIDEO GND VS
ASCO®

© 2020 ASCO Power Technologies. All Rights Reserved
6
IO-75024
01/2020
For access to self-service tools and chat support visit se.com/us/en/work/support or call 1-888-778-2733 for technical assistance
Model 159 (Edco HVCP-48)
Surge Protective Device (SPD)
General Technical
Specications DC Power (VS)
Operating Voltage 48 VDC
Clamping Voltage 70 VDC
Operating Current 1 Amp maximum
Peak Surge Current 10 kA (8 x 20µs)
SPD Technology GDT, SAD, Series Element
Connection Type 5.08mm Terminal Block Plug
High Speed Data (SDIO)
Clamping Voltage 15 VDC
Operating Current 0.15 A maximum
Peak Surge Current 10 kA (8 x 20µs)
SPD Technology GDT, SAD, Series Element
Connection Type 5.08mm Terminal Block Plug
Video
Clamping Voltage 2 VDC
Peak Surge Current 10 kA (8 x 20µs)
SPD Technology GDT, SAD, Series Element
Connection Type Female BNC Jack or 5.08mm
Terminal Block Plug
Physical Data
Ground Wire (in. / mm.) 12 AWG, 36.0 in. [914.4 mm.] Long
Terminal Wire Range 28-12 AWG
Wiring Terminal Torque 4.5 LB in
Wiring Terminal Strip
Length (in. / mm.) 0.28 - 0.31 in. [7.11 - 7.87 mm.]
Dimensions (in. / mm.) 3.3 x 3.3 x 1.35 in.
[83.82 x 83.82 x 34.29 mm.]
Material High Impact Plastic
Weight (oz. / kg.) 12 oz. [0.34 kg.]
Mounting Flange mounted, 3.75 in. mounting hold distance,
(0.188 in. dia.) (2x) DIN-Rail mounting (Optional)
Operating Temperature -40°C to +74°C
Operating Humidity 0% to 95% Non-condensing
Certications
RoHS Compliant, UL497B, Tested to IEC 802.11
Limited warranty 5 Year

© 2020 ASCO Power Technologies. All Rights Reserved 7
IO-75024
01/2020
For access to self-service tools and chat support visit se.com/us/en/work/support or call 1-888-778-2733 for technical assistance
Model Cross Reference MODEL
Former Model Name APPLICATION
159D070S10KAN6N0
Edco HVCP-48 Analog Camera
159D070S10KAN6J0
Edco HVCP-48-4X
Analog Camera
wtih NEMA 4X Enclosure
159D070S10KANBN0
Edco HVCP-48-BNC BNC Video, Hardwire Power and Data
159D070S10KANBJ0
Edco HVCP-48-BNC-4X
BNC Video, Hardwire Power and Data
with NEMA 4X Enclosure
ACCESSORY
HVDIN
11852KIT DIN Mounting Kit
Model 159 (Edco HVCP-48)
Surge Protective Device (SPD)

IO-75024 Rev- 01-20
14550 58th Street North
Clearwater, Florida 33760
se.com/us/en/work/support
1-888-778-2733
While every precaution has been taken to ensure accuracy and
completeness in this literature, Schneider Electric assumes no
responsibility, and disclaims all liability for damages resulting from
use of this information or for any errors or omissions.