Asgard CENTURION User manual

It is always recommended to anchor the unit to the ground. Drill through
the four holes in each of the base of the unit using 6mm dia masonry drill
to a depth of 70mm. Screw in the anchor fixings. (These have a self
cutting thread). If not anchoring the unit, fit the self seal plugs BEFORE
BUILDING to seal the fixing holes from underneath. Please note
product must be bolted down to comply with LPS1175.
TOOLS REQUIRED
Power driver POSI-DRIV screwdriver, 6mm dia. masonry drill and a
10mm socket or spanner.
CENTURION
LH F. SIDE PANEL
32941 x1
LH R. SIDE PANEL
32874 x1
F. BASE PANEL
32940 x1
R. BASE PANEL
32871 x1
LH DOOR
32943 x1
RH DOOR
32944 x1
FRONT FASCIA
32948 x1
ZSCREW32 x8
ZSILCO1 x1
ZSCREW04 x4
ZSCREW100 x185
ZSCREW340 x24
32670 x16
10mm
Spanner
18V
ZCOMPPLZS02 x8
ZCOMPPLAS22-23-24 x12
4x 2mm, 4x 3mm, 4x 5mm
BASE COVER CHANNEL 37364 x1
SIDE COVER CHANNEL 32916 x2
ROOF COVER CHANNEL 32918 x2
F. TOP PANEL
32986 x1
TOP SHROUD
32945 x2
R. TOP PANEL
32987 x1
RH F. SIDE PANEL
32942 x1
RH R. SIDE PANEL
32875 x1
BASE INSTRUCTIONS
Flat and firm base. Recommended: concrete, tarmac or paving flags.
Min. distance from walls/ shrubbery: 1000mm.
Min. base size (WxDxH) 2640mm x 1730mm x 50mm.
LEVELING THE UNIT
Correctly level the constructed unit using the shims (ZCOMPPLAS)
provided prior to fixing the unit to the ground. Slide the packing pieces
under the corners of the unit base as required until an equal gap has
been achieved around the door allowing for its smooth operation and
alignment.
LH BACK PANEL
32867 x1
RH BACK PANEL
32876 x1
For maintenance instructions of this product visit www.asgardsss.co.uk
Warning: some panels may weigh over 20Kg
Beware of manual handling
Warning: Please keep
this key card safe! Refer
to if replacement key is
required.
x2
SEALANT
00001
YOUR UNIQUE
KEY CODE
ROOF JOINT
STRIP 40446 x2
6mm
Dia.
Posi-Driv
Screwdriver

RH BACK PANEL
32876
RH R. SIDE PANEL
32875
REAR BASE PANEL
32871
x15
1
3
5 6
4
2
x19 x22
x10
PLEASE NOTE ALL SCREWS ARE FIXED FROM THE INSIDE
LH R. SIDE PANEL
32874
x16 x13
R. TOP PANEL
32987
F. BASE PANEL
32940 x1
LH BACK PANEL
32867
x15
x3
x7
x3
x16
x7
x15
x13
x4
x4
x4
x4
IF YOU HAVE AN OPTIONAL RAMP,
PLACE UNDERNEATH FRONT
BASE PANEL AT THIS STAGE
!

7 8
910
11 12
x34 x6
x30 x24
x4 x4
LH F. SIDE PANEL
32941
RH F. SIDE PANEL
32942
FRONT FASCIA
32948
F. TOP PANEL
32986
LH DOOR
32943
RH DOOR
32944
1ST TOP SHROUD
32945
2ND TOP SHROUD
32945
SHROUDS 32945
x15
x3
x3
x15
x7
x7
x4
x4
x4
x4 x7
x7
x2
x2
x4
x3
x3
x3
x3
x3
x3
x3
x3
SHROUDS
ROOF STRIP
ROOF JOINT STRIP 40446
APPLY TO BOTH INSIDE EDGES AND FIT FIRST ROOF JOINT STRIP 40446
ROOF JOINT STRIP END
40446
NO SCREWS REQUIRED
TOP END OF STRIP TRAPPED
UNDER TOP CAP
!

13 14
15 16
17
www.asgardsss.co.uk
x16
REMOVE SCREWS WHICH ALIGN
WITH THE COVER CHANNELS.
ALIGN AND PLACE SCREWS BACK
!
REMOVE SCREWS WHICH ALIGN
WITH THE COVER CHANNELS.
ALIGN AND PLACE SCREWS BACK
!
SIDE COVER CHANNEL 32916
BASE COVER CHANNEL 37364
033015/16.10.19/KW/REV1
ROOF COVER CHANNEL 32918
32670
x8
LEVEL SHED UNTIL DOORS
ALIGN USING ZCOMPPLAS
AS SUITABLE
!
ZCOMPPLAS22-23-24