Asko W8844XLW User manual

Dear Customer,
Read these instructions carefully and completely before you install the
machine. The installation should be carried out by a qualified person who
is familiar with all local codes and ordinances for electrical and plumbing
connections. See also the general Safety Instructions in the Use & Care
Guide.
Cosmetic damage must be reported to the ASKO dealer within five
days from the date of purchase. As soon as you unpack the machine,
thoroughly check it for cosmetic damage.
Installation Instructions for Washing Machine
DOMESTIC

2
Customer Care Center, 1-800-898-1879, www.askona.com
INSTALLATION
Read these instructions carefully and completely before
you install the machine. The installation should be
carried out by a qualified person who is familiar with all
local codes and ordinances for electrical and plumbing
connections.
Cosmetic damage must be reported to your dealer within
five days from the date of purchase. After unpacking the
washer, thoroughly check the unit for cosmetic damage.
LEVELING THE MACHINE
It is important that the machine is level to prevent
excessive vibrations during spin cycles. Each foot of the
washer is adjustable, so you can level the washer on any
surface. Once it is level, securely tighten the lock nuts
on the feet to prevent excessive vibration during spin
cycles.
Be sure to tighten the
lock nuts securely
when you level the
machine.
WATER SUPPLY CONNECTION
Since ASKO washers have a built-in heating element,
you only need a cold water inlet. The connection should
be made by someone who is sufficiently skilled. Use
the hose supplied with the washer. (The inlet hose is
marked for correct connection.) The water pressure
must be in the range 15–146 PSI. A valve should be fitted
on the water supply pipe. If a new supply pipe has been
installed for the washer, it should be flushed thoroughly
to remove any foreign particles that might clog the filter
in the fill valve.
NOTE!
If the unit is installed on a second storey, follow local
building codes. We recommend installing a drip pan.
DRAIN OUTLET CONNECTION
The machine is supplied with the outlet hose already
attached. The hose should be extended over a suitable
sink edge or drain pipe at a height of 24” to 36” (610 mm
to 914 mm) above the bottom of the unit. (The lower
height is preferable.) Make sure the hose is not kinked.
24" to 36"
NOTE!
If the hose is extended, the internal diameter of the
coupling must not be less than ½”.
WARNING
Do not extend the drain hose higher than 36” (914 mm)
from the bottom of the unit.
ELECTRICAL INSTALLATION
The machine is delivered ready-fitted with a plug and
is intended for connection to an ASKO Dryer, which is
equipped with a matching receptacle. The plug supplied
with the washer can only be used with an ASKO Dryer.
If the washer is used separately or with another dryer, it
must be on a separate 208-240 V single-phase circuit.
If the machine is to be used in a wet area, the supply
must be protected by a residual current device.
As supplied: 208-240 V, 60 Hz, 2000 heating element,15
A timed delayed fuse is required.
WARNING
Connection to a permanently wired supply point must
be made only by a qualified electrician.
NOTE!
Repairs and maintenance relating to safety or
performance must be carried out by a qualif ed
professional.

3
Customer Care Center, 1-800-898-1879, www.askona.com
INSTALLATION
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of
malfunction or breakdown, grounding will reduce the risk
of electric shock by providing a path of least resistance
for electric current. This appliance is equipped with a
cord having an equipment-grounding conductor and
a grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded
in accordance with all local codes and ordinances.
FREESTANDING INSTALLATION
The washer can be placed next to the dryer. It is
essential that the machine is leveled and the locknuts
are tightened to prevent excessive vibration during
spin cycles. Also be sure to leave a minimum of ½” of
space between the washer and the dryer. The height
adjustment for the washer is 33½” to 34½” (850 mm to
876 mm). Do not raise it higher than 34½” (876 mm).
WARNING
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check
with a qualified electrician or serviceman if you are
in doubt as to whether the appliance is properly
grounded.
Do not modify the plug provided with the appliance. If
it will not fit the outlet, have a proper outlet installed by
a qualified electrician.
STACKED INSTALLATION
ASKO washers should never be stacked on a counter or
a dryer. You can, however, stack an ASKO dryer on an
ASKO washer. Refer to your Dryer Use and Care Guide
for instructions on how to do this.
BUILT-IN INSTALLATION
ASKO washers can be installed beneath a cabinet or
worktop with a height of 34” to 35” (863 to 889 mm) or
in a closet. There must be a gap of about ½” (12 mm) all
around the machine, including between the rear edge of
the machine’s top panel and the back wall. The opening
width must be at least 24½” (622 mm). Space must
also be available for the fill and drain hoses. See the
illustration below for measurements and positions. If the
washer is installed in a closet the door must be left open
while the washer is running.
If the drain outlet is higher than 24”(610 mm), the
connections will need to be recessed.

www.askona.com
We reserve the right to make changes.
WM80.2  en (05-17)