ASROCK iBOX-345-DL User manual

iBOX-420-DL
iBOX-345-DL
User Manual
Version 1.0
Published March 2021

Important Safety Instructions
Pay close attention to the following safety instructions before performing any of
the operation. Basic safety precautions should be followed to protect yourself from
harm and the product from damage:
• Operation of the product should be carried out by suitably trained, qualied, and
certied personnel only to avoid risk of injury from electrical shock or energy hazard.
• Disconnect the power cord from the wall outlet when installing or removing main
system components, such as the motherboard and power supply unit.
• Place the system on a stable and at surface.
• Use extreme caution when working with high-voltage components.
• When handling parts, use a grounded wrist strap designed to prevent static discharge.
• Keep the area around the system clean and clutter-free.
• Keep all components and printed circuit boards (PCBs) in their antistatic bags when
not in use.
• Handle a board by its edges only; do not touch its components, peripheral chips,
memory modules or contacts.
e terms HDMI®and HDMI High-Denition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.

Contents
Chapter 1 Introduction 1
1.1 Package Contents 1
1.2 Product Specications 2
Chapter 2 Product Overview 4
2.1 Front View 4
2.2 Rear View 5
2.3 Inside View 6
Chapter 3 Hardware Installation 7
3.1 How to Remove the Bottom Case 7
3.2 How to Install the WiFi Module (Optional) 8
3.3 How to Install the mSATA SSD 9
3.4 How to Install the 2.5-inch Hard Drive 10
3.5 How to Install the Memory Modules
(DDR3 Low Voltage (1.35V)) 12
3.6 How to Install the VESA Bracket 13
3.7 Positions of the iBOX-420-DL / iBOX-345-DL 14
Chapter 4 Motherboard 15
4.1 Motherboard Layout 15
4.2 Motherboard Specications 16
4.3 Jumpers Setup 18
4.4 Onboard Headers and Connectors 19
4.5 Expansion Slots (M.2 Sockets) 21

Chapter 5 UEFI SETUP UTILITY 22
5.1 Introduction 22
5.1.1 UEFI Menu Bar 22
5.1.2 Navigation Keys 23
5.2 Main Screen 24
5.3 Advanced Screen 25
5.3.1 CPU Conguration 26
5.3.2 Chipset Conguration 28
5.3.3 Storage Conguration 30
5.3.4 Super IO Conguration 31
5.3.5 ACPI Conguration 32
5.3.6 Trusted Computing 33
5.4 Hardware Health Event Monitoring Screen 34
5.5 Security Screen 35
5.6 Boot Screen 36
5.7 Exit Screen 38
Chapter 6 Software Support 39
6.1 Install Operating System 39
6.2 Support CD Information 39

iBOX-420-DL / iBOX-345-DL
PB 1
English
Chapter 1 Introduction
1.1 Package Contents
• iBOX-420-DL / iBOX-345-DL Barebone System with:
iBOX-420-DL / iBOX-345-DL Chassis
Motherboard (pre-installed)
*e barebone system does not include memory, hard drive and mSATA SSD.
• Power Adapter (36W/12V) & Power Plug
• SATA Data and Power Cable
• mSATA Screw
• VESA Mount Bracket & Screw Package
• Support CD
• Quick Installation Guide
Because the hardware specications might be updated, the content of this documentation
will be subject to change without notice.
If any items are missing or appear damaged, contact your authorized dealer.

2 3
English
1.2 Product Specications
iBOX-420-DL
iBOX-345-DL Barebone
CPU Intel® Apollo Lake N4200/N3350/J3455 Processor
OS N/A
Chipset Intel® N4200/N3350/J3455 SoC
Memory Supports DDR3L, 2 x SO-DIMM slots, Max. 8GB
HDD
N/A
Optional
Supports 1 x 2.5" SATA HDD*
LAN Gigabit LAN
WiFi Optional
Front I/O 1 x USB 3.0, 1 x Audio-out with MIC-In
Rear I/O 1 x HDMI, 2 x DP, 2 x USB 3.0, 2 x LAN, 1 x Kensington lock
Power Unit 36W/12V Adapter
Dimension 135mm (W) x 44.5mm (H) x 110mm (D)
VESA Bracket included , supports 75 x 75 and 100 x 100 mm
eMMC
mSATA
slot
2.5”HDD

iBOX-420-DL / iBOX-345-DL
2 3
English
* For iBOX-420-DL/iBOX-345-DL, it is not recommended to install 2.5” HDD. If you install the 2.5” HDD, please
keep the iBOX-420-DL/iBOX-345-DL in a vertical position to ensure better cooling performance.
Volume
(Liters) 0.6L
Operating
Temperature 0°C~50°C

4 5
English
Chapter 2 Product Overview
is chapter provides diagrams showing the location of important components of
the iBOX-420-DL/iBOX-345-DL.
2.1 Front View
No. Description
1Headphone & Microphone
2 USB 3.0 (Type A)
12

iBOX-420-DL / iBOX-345-DL
4 5
English
2.2 Rear View
No. Description
1 Kensington Lock Slot
2DC-In
3*DisplayPort
4HDMI
5 USB 3.0 (Type A)
6RJ-45
*To use DisplayPort as a display output, please connect your monitor/display to
HDMI Port when installing OS system.
is DisplayPort only supports DP to D-Sub dongle and does not support DP to
HDMI dongle and DP to DVI dongle.
* ere are two LEDs on the LAN port. Please refer to the table below for the LAN port LED indications.
Activity / Link LED Speed LED
Status Description Status Description
O No Link O 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Link Green 1Gbps connection
ACT/LINK LED
SPEED LED
LAN Port
1 2 345
63

6 PB
English
2.3 Inside View
No. Description
1 WiFi Module Slot
2mSATA Slot
3SO-DIMM Slots
4 SATA 3.0 Connector
5 Clear CMOS Pad
*Clear CMOS Pad allows you to clear the data in CMOS. To clear CMOS, disconnect the
power supply and short the Clear CMOS Pad.
6 Hard disk drive tray (compatible with 2.5" SATA HDD)
SO-DIMM memory, hard drive and mSATA SSD are not included with this system.
2
1
5
3
4
6

iBOX-420-DL / iBOX-345-DL
PB 7
English
Chapter 3 Hardware Installation
is chapter helps you install or remove important components.
3.1 How to Remove the Bottom Case
1. Remove the four screws on the bottom case.
2. en li up and remove the bottom panel..
2
1

8 9
English
3.2 How to Install the WiFi Module (Optional)
1. Locate the WiFi Module slot on the motherboard.
2. Carefully insert the WiFi Module into the slot.
3. Tighten the screw to secure the WiFi Module to the motherboard.

iBOX-420-DL / iBOX-345-DL
8 9
English
3.3 How to Install the mSATA SSD
1. Locate the mSATA slot on the motherboard.
2. Carefully insert the mSATA SSD into the slot.
3. Tighten the screw to secure the mSATA SSD to the motherboard.

10 11
English
3.4 How to Install the 2.5-inch Hard Drive
1. Remove the four screws on the bottom case. en li up and remove the bottom panel.
2. Attach the HDD cage to the bottom panel and secure it using the four screws.
en connect the SATA cable to the HDD.

iBOX-420-DL / iBOX-345-DL
10 11
English
3. Connect the SATA Data and Power Cable to the motherboard.
4. en reinstall the bottom panel.
1
2

12 13
English
3.5 How to Install the Memory Modules
(DDR3 Low Voltage (1.35V))
1. Carefully insert the SO-DIMM memory modules into the slot at a 30-degree angle.
2. Push down until the modules snap into place.
1. e iBOX-420-DL / iBOX-345-DL requires DDR3L SO-DIMM (1.35V).
2. For dual channel conguration, you always need to install identical (the same brand,
speed, size and chip-type) DDR3L SO-DIMM pairs.
e SO-DIMM only ts in one correct orientation. It will cause permanent damage to the
motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.

iBOX-420-DL / iBOX-345-DL
12 13
English
3.6 How to Install the VESA Bracket
1. Attach the two screws to the base of the iBOX-420-DL / iBOX-345-DL.
2. 2. Attach the VESA Bracket to the rear of a compatible display using the four screws.
*Choose mounting holes depending on the mounting hole pattern of your LCD screen
(75 mm × 75 mm or 100 mm × 100 mm).
3. Mount the iBOX-420-DL / iBOX-345-DL by sliding it into place.
DC-IN Jack on Top

14 15
English
3.7 Positions of the iBOX-420-DL / iBOX-345-DL
e iBOX-420-DL / iBOX-345-DL can be placed in vertical or horizontal position.
Horizontal Position Wall-mounted
DC-IN Jack on Top

iBOX-420-DL / iBOX-345-DL
14 15
English
Chapter 4 Motherboard
4.1 Motherboard Layout
LAN1
AUDIO1
HDMI1
USB3_2
DC_IN1
M.2KEY M
USB3.0: USB3_1
DP2
DISPLAY1
PANEL1
HDLED RESET
PLED PWRBTN
1
SATA3_1
DDR3_A1 (SupportDDR3L Only)
DDR3_B1 (SupportDDR3L Only)
SATA_PWR1
1
N4200-NUC-DL
Industrial
LAN2
USB3.0: USB3_3
M.2KEY E
1
PWR_JP1
1
COM1
1
USB2_4_5
BIOS
Chip
1
CLRMOS1
1 : M.2 Socket ( Key-M) (M2M_1)
2 : M.2 Socket ( Key-E) (M2E_1)
3 : Clear CMOS Header (CLRMOS1)
4 : COM Port Header (COM1)
5 : USB2.0 Header (USB2_4_5)
6 : ATX/AT Mode Select (PWR_JP1)
7 : System Panel Header (PANEL1)
8 : SATA Power Output Connector (SATA_PWR1)
9 : SATA3 Connector (SATA3_1)

16 17
English
4.2 Motherboard Specications
Form
Factor Dimensions 4.09" x 4.02" (104 x 102mm)
Processor
System
CPU Intel®Apollo Lake J3455/N4200/N3350 SoC
Chipset Intel®SoC
Expansion
Slot
PCIe N/A
Mini-PCIe N/A
mSATA N/A
M.2 1 x M.2 2230, Key E (PCIe x1 +USB2.0), 1 x M.2
2242/2260, Key M with SATA3 for SSD
Memory
Technology Dual Channel DDR3L 1867
Max. 16GB
Socket 2 x SO-DIMM
Graphics
Controller Intel®Gen9 Graphics DX 11/12, OGL4.3/4.4
VGA N/A
DVI N/A
LVDS N/A
HDMI Supports HDMI 1.4b, Max. resolution 3840 x
2160@30Hz
DisplayPort Supports DP 1.2, Max. resolution 4096 x
2160@60Hz
MultiDisplay Triple Display
eDP N/A
Ethernet Ethernet 10/100/1000 Mbps
Controller 2 x Realtek RTL8111G
Rear I/O
VGA N/A
DVI N/A
HDMI 1
DisplayPort 2
Ethernet 2
USB 2 x USB 3.0
Audio 1 x (Mic-in, Line-out)
Serial N/A
PS/2 N/A