ASROCK AM2V890-VSTA User manual

11
11
1
AM2V890-VSTA
User Manual
Version 1.1
Published July 2006
Copyright©2006 ASRock INC. All rights reserved.

22
22
2
Copyright Notice:Copyright Notice:
Copyright Notice:Copyright Notice:
Copyright Notice:
No part of this manual may be reproduced, transcribed, transmitted, or translated in
any language, in any form or by any means, except duplication of documentation by
the purchaser for backup purpose, without written consent of ASRock Inc.
Products and corporate names appearing in this manual may or may not be regis-
tered trademarks or copyrights of their respective companies, and are used only for
identification or explanation and to the owners’ benefit, without intent to infringe.
Disclaimer:Disclaimer:
Disclaimer:Disclaimer:
Disclaimer:
Specifications and information contained in this manual are furnished for informa-
tional use only and subject to change without notice, and should not be constructed
as a commitment by ASRock. ASRock assumes no responsibility for any errors or
omissions that may appear in this manual.
With respect to the contents of this manual, ASRock does not provide warranty of
any kind, either expressed or implied, including but not limited to the implied warran-
ties or conditions of merchantability or fitness for a particular purpose.
In no event shall ASRock, its directors, officers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of profits, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the manual or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
ASRock Website: http://www.asrock.com

33
33
3
ContentsContents
ContentsContents
Contents
1.1.
1.1.
1. IntroductionIntroduction
IntroductionIntroduction
Introduction ........................................................................................................................
........................................................................................................................
............................................................ 55
55
5
1.1 Package Contents..................................................................... 5
1.2 Specifications ........................................................................... 6
1.3 Minimum Hardware Requirement Table for Windows®VistaTM
Premium and Basic Logo .......................................................... 9
1.4 Motherboard Layout ................................................................. 10
1.5 HD8CHI/OPanel....................................................................... 11
2.2.
2.2.
2. InstallationInstallation
InstallationInstallation
Installation ............................................................................................................................
............................................................................................................................
.............................................................. 1212
1212
12
Pre-installation Precautions ............................................................... 12
2.1 CPUInstallation ......................................................................... 13
2.2 Installation of CPU Fan and Heatsink ....................................... 13
2.3 Installation of Memory Modules (DIMM).................................... 14
2.4 Expansion Slots (PCI and PCIE Slots) .............................................. 16
2.5 Dual Graphics Feature .............................................................. 17
2.6 Jumpers Setup.......................................................................... 18
2.7 Onboard Headers and Connectors.......................................... 19
2.8 HDMI_SPDIF Header ConnectionGuide.................................... 23
2.9 Serial ATA (SATA) Hard Disks Installation ................................ 24
2.10 Hot Plug and Hot Swap Functions for SATA HDDs ................. 24
2.11 Driver Installation Guide ............................................................ 24
2.12 Installing Windows®2000 / XP / XP 64-bit / VistaTM With RAID
Functions .................................................................................. 25
2.13 Installing Windows®2000 / XP / XP 64-bit / VistaTM Without RAID
Functions .................................................................................. 26
2.14 Untied Overclocking Technology.............................................. 26
3.3.
3.3.
3. BIOS SBIOS S
BIOS SBIOS S
BIOS SETUP UTILITYETUP UTILITY
ETUP UTILITYETUP UTILITY
ETUP UTILITY ......................................................................................................
......................................................................................................
................................................... 2727
2727
27
3.1 Introduction ............................................................................... 27
3.1.1 BIOS Menu Bar ............................................................... 27
3.1.2 Navigation Keys ............................................................. 28
3.2 Main Screen.............................................................................. 28
3.3 Advanced Screen .................................................................... 29
3.3.1 CPU Configuration .......................................................... 30
3.3.2 Chipset Configuration..................................................... 32
3.3.3 ACPI Configuration ......................................................... 34
3.3.4 IDE Configuration ............................................................ 35
3.3.5 PCIPnPConfiguration ...................................................... 37
3.3.6 Floppy Configuration ...................................................... 37
3.3.7 Super IO Configuration................................................... 38
3.3.8 USB Configuration .......................................................... 39

44
44
4
3.4 Hardware Health Event Monitoring Screen ............................. 40
3.5 Boot Screen.............................................................................. 40
3.5.1 Boot Settings Configuration ........................................... 41
3.6 Security Screen........................................................................ 41
3.7 Exit Screen ............................................................................... 42
4.4.
4.4.
4. Software SupportSoftware Support
Software SupportSoftware Support
Software Support ......................................................................................................
......................................................................................................
................................................... 4343
4343
43
4.1 Install Operating System........................................................... 43
4.2 Support CD Information............................................................. 43
4.2.1 Running Support CD....................................................... 43
4.2.2 Drivers Menu .................................................................. 43
4.2.3 Utilities Menu ................................................................... 43
4.2.4 Contact Information ........................................................ 43
APPENDIX: AMD’s Cool ‘n’ QuietAPPENDIX: AMD’s Cool ‘n’ Quiet
APPENDIX: AMD’s Cool ‘n’ QuietAPPENDIX: AMD’s Cool ‘n’ Quiet
APPENDIX: AMD’s Cool ‘n’ QuietTMTM
TMTM
TM TT
TT
T
echnologyechnology
echnologyechnology
echnology............
............
...... 4444
4444
44

55
55
5
1.1.
1.1.
1. IntroductionIntroduction
IntroductionIntroduction
Introduction
Thank you for purchasing ASRock AM2V890-VSTA motherboard, a reliable
motherboard produced under ASRock’s consistently stringent quality control. It de-
livers excellent performance with robust design conforming to ASRock’s commit-
ment to quality and endurance.
In this manual, chapter 1 and 2 contain introduction of the motherboard and step-by-
step guide to the hardware installation. Chapter 3 and 4 contain the configuration
guide to BIOS setup and information of the Support CD.
Because the motherboard specifications and the BIOS software might be
updated, the content of this manual will be subject to change without
notice. In case any modifications of this manual occur, the updated
version will be available on ASRock website without further notice. You
may find the latest VGA cards and CPU support lists on ASRock website
as well. ASRock website http://www.asrock.com
1.11.1
1.11.1
1.1 Package ContentsPackage Contents
Package ContentsPackage Contents
Package Contents
1 x ASRock AM2V890-VSTA Motherboard
(ATX Form Factor: 12.0-in x 8.0-in, 30.5 cm x 20.3 cm)
1 x ASRock AM2V890-VSTA Quick Installation Guide
1 x ASRock AM2V890-VSTA Support CD
1 x Ultra ATA 66/100/133 IDE Ribbon Cable (80-conductor)
1 x 3.5-in Floppy Drive Ribbon Cable
1 x SerialATA (SATA) Data Cable (Optional)
1 x SerialATA (SATA) HDD Power Cable (Optional)
1 x HDMI_SPDIF Cable (Optional)
1 x HD 8CH I/O Shield

66
66
6
1.21.2
1.21.2
1.2 SpecificationsSpecifications
SpecificationsSpecifications
Specifications
Platform - ATX Form Factor: 12.0-in x 8.0-in, 30.5 cm x 20.3 cm
CPU - AM2 940-Pin Socket Supporting AMDAthlonTM 64 / 64FX /
64X2 and SempronTM Processors
- Supports AMD’s Cool ‘n’ QuietTM Technology
(see CAUTION 1)
- FSB 1000 MHz (2.0 GT/s)
- Supports Untied Overclocking Technology (see CAUTION 2)
- Supports Hyper-Transport Technology
Chipset - Northbridge: VIA® K8T890 chipset
- Southbridge: VIA®8237A
Memory -Dual Channel DDRII Memory Technology (see CAUTION 3)
- 4 xDDRIIDIMM slots
- SupportDDRII800/667/533
- Max. capacity: 8GB
Hybrid Booster - CPU Frequency Stepless Control (see CAUTION 4)
-ASRock U-COP (see CAUTION 5)
- Boot Failure Guard (B.F.G.)
Expansion Slot - 3 x PCI slots
- 1 x PCI Express x16 slot
- 1 x PCI Express x4 / x1 slot
- 1 x PCI Express x1 slot
Audio - RealtekALC888 7.1channel CODEC with HighDefinition
Audio
LAN - VIA®PHY VT6103
- Speed: 10/100 Ethernet
- Supports Wake-On-LAN
Rear Panel I/O HD8CHI/O
- 1 x PS/2 Mouse Port
- 1 x PS/2 Keyboard Port
- 1 x Serial Port: COM1
- 1 x Parallel Port (ECP/EPP Support)
- 4 x Ready-to-Use USB 2.0 Ports
- 1 x RJ-45 Port
- HDAudio Jack: Side Speaker/Rear Speaker/Central/Bass/
Line in/Front Speaker/Microphone (see CAUTION 6)

77
77
7
Connector - 2 x Serial ATA 1.5Gb/s connectors, support RAID
(RAID 0, 1, JBOD) and “Hot Plug” functions
- 2 x ATA133 IDE connectors (support 4 x IDE devices)
- 1 x Floppy connector
- 1 x IR header
- 1 x Game header
- 1 x HDMI_SPDIF header
- CPU/Chassis FANconnector
- 20 pin ATX power connector
- 4 pin 12V power connector
- CD in header
- Front panel audio connector
- 2 x USB 2.0 headers (support 4 USB 2.0 ports)
(see CAUTION 7)
BIOS Feature - 4MbAMI BIOS
-AMI Legal BIOS
- Supports “Plug and Play”
-ACPI 1.1 Compliance Wake Up Events
- Supports jumperfree
- SMBIOS 2.3.1 Support
Support CD - Drivers, Utilities, AntiVirus Software (Trial Version)
Hardware - CPU Temperature Sensing
Monitor - Chassis Temperature Sensing
- CPU FanTachometer
- Chassis Fan Tachometer
- CPU Quiet Fan
- Voltage Monitoring: +12V, +5V, +3.3V, Vcore
OS - Microsoft® Windows® 2000/XP/XP 64-bit/VistaTM compliant
(see CAUTION 8)
Certifications - FCC, CE, Microsoft®WHQL Certificated

88
88
8
CAUTION!
1. For power-saving’s sake, it is strongly recommended to enable AMD’s Cool ‘n’
QuietTM technology under Windows system. See APPENDIX on page 44 to
enable AMD’s Cool ‘n’ QuietTM technology.
2. This motherboard supports Untied Overclocking Technology. Please read “Un-
tied Overclocking Technology” on page 26 for details.
3. This motherboard supportsDual Channel Memory Technology. Before you
implement Dual Channel Memory Technology, make sure to read the
installation guide of memory modules on page 14 for proper installation.
4. Although this motherboard offers stepless control, it is not recommended to
perform over-clocking. Frequencies other than the recommended CPU bus
frequencies may cause the instability of the system or damage the CPU.
5. While CPU overheat is detected, the system will automatically shutdown.
Before you resume the system, please check if the CPU fan on the motherboard
functions properly and unplug the power cord, then plug it back again. To
improve heat dissipation, remember to spray thermal grease between the
CPU and the heatsink when you install the PC system.
6. For microphone input, this motherboard supports both stereo and mono
modes. For audio output, this motherboard supports 2-channel, 4-channel,
6-channel, and 8-channel modes. Please check the table on page 11 for
proper connection.
7. Power Management for USB 2.0 works fine under Microsoft®Windows®
VistaTM / XP 64-bit / XP SP1 or SP2 / 2000 SP4.
8. Microsoft®Windows®VistaTM driver is not ready yet. We will update it to our
website in the future. Please visit our website for Microsoft®Windows®VistaTM
driver and related information.
ASRock website http://www.asrock.com

99
99
9
1.31.3
1.31.3
1.3 Minimum Hardware RMinimum Hardware R
Minimum Hardware RMinimum Hardware R
Minimum Hardware Requirement Tequirement T
equirement Tequirement T
equirement Table for Wable for W
able for Wable for W
able for Windowsindows
indowsindows
indows®®
®®
®
VistaVista
VistaVista
VistaTMTM
TMTM
TM Premium and Basic LogoPremium and Basic Logo
Premium and Basic LogoPremium and Basic Logo
Premium and Basic Logo
For system integrators and users who purchase this motherboard and
plan to submit Windows®VistaTM Premium and Basic logo, please follow the
below table for minimum hardware requirement. Please adopt the CPU,
memory, and VGA that we suggest.
CPU Sempron2800+
Memory 512MB Single Channel
VGA DX9.0 with WDDM Driver
with 128bit VGA memory (Premium)
with 64bit VGA memory (Basic)

1010
1010
10
1.4 Motherboard Layout1.4 Motherboard Layout
1.4 Motherboard Layout1.4 Motherboard Layout
1.4 Motherboard Layout
Super
I/O
`
PCI
EXPRESS
USB2.0
CMOS
BATTERY
ATXPWR1
SOCKET AM2
AM2V890-VSTA
CD1
VIA
K8T890
Chipset
VIA
8237A
Chipset
ATX12V1
PS2_USB_PWR1
1
USB 2.0
T: USB 2
B: USB3
PARALLEL PORT
COM1
PS2
Mouse
PS2
Keyboard
Top:
REAR SPK
Center:
SIDE SPK
Bottom:
CTR BASS
Top:
LINE IN
Center:
FRONT
Bottom:
MIC IN
USB 2.0
T: USB 0
B: USB1
Top:
RJ-45
IDE2
FSB800
DDRII_1 (64/72 bit, 240-pin module)
DDRII_2 (64/72 bit, 240-pin module)
FSB800
DDRII_3 (64/72 bit, 240-pin module)
DDRII_4 (64/72 bit, 240-pin module)
PCIE1
PCI1
PCI2
4Mb
BIOS
LAN
PHY
AUDIO
CODEC
SATA1
SATA2
1
CLRCMOS1
DDRII800
Dual Core CPU
FSB1GHz
Dual Channel
ATA133
SATA
7.1CH HD
RAID
CPU_FAN1
HDLED RESET
PLED PWRBTN
1
PANEL1
CHA_FAN1
SPEAKER1
1
USB67
1
USB45
1
IR1
FLOPPY1
GAME1
1
HD_AUDIO1
1
RoHS
30.5cm (12.0-in)
20.3cm (8.0-in)
67
124
35
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
IDE1
PCIE2
PCIE3
PCI3
1
1
J1
1
HDMI_SPDIF1
32
1 PS2_USB_PWR1 Jumper 16 System Panel Header (PANEL1)
2 ATX 12V Power Connector (ATX12V1) 17 Primary Serial ATA Connector (SATA1,black)
3 CPU Fan Connector (CPU_FAN1) 18 Chassis Speaker Header (SPEAKER 1)
4 CPU Heatsink Retention Module 19 Chassis Fan Connector (CHA_FAN1)
5 AM2 940-Pin CPU Socket 20 Flash Memory
6 2 x 240-pin DDRII DIMM Slots 21 Floppy Connector (FLOPPY1)
(Dual Channel A: DDRII_1, DDRII_2; Yellow) 22 Game Port Header (GAME1)
7 2 x 240-pin DDRII DIMM Slots 23 HDMI_SPDIF Header (HDMI_SPDIF1)
(Dual Channel B: DDRII_3, DDRII_4; Orange) 24 Front Panel Audio Header (HD_AUDIO1)
8 North Bridge Controller 25 PCI Slots (PCI1- 3)
9 Clear CMOS Jumper (CLRCMOS1) 26 PCI Express x4 / x1 Slot (PCIE3)
10 USB 2.0 Header (USB67, Blue) 27 Infrared Module Header (IR1)
11 USB 2.0 Header (USB45, Blue) 28 J1 Jumper
12 South Bridge Controller 29 PCI Express x1 Slot (PCIE2)
13 Primary IDE Connector (IDE1, Blue) 30 PCI Express x16 Slot (PCIE1)
14 Secondary IDE Connector (IDE2, Black) 31 Internal Audio Connector: CD1 (Black)
15 Secondary Serial ATA Connector (SATA2, black) 32 ATX Power Connector (ATXPWR1)

1111
1111
11
1.51.5
1.51.5
1.5 HD 8CH I/OHD 8CH I/O
HD 8CH I/OHD 8CH I/O
HD 8CH I/O
PanelPanel
PanelPanel
Panel
1 Parallel Port 8 Microphone (Pink)
2 RJ-45 Port 9 USB 2.0 Ports (USB01)
3 Side Speaker (Gray) 10 USB 2.0 Ports (USB23)
4 Rear Speaker (Black) 11 Serial Port: COM1
5 Central / Bass (Orange) 12 PS/2 Keyboard Port (Purple)
6 Line In (Light Blue) 13 PS/2 Mouse Port (Green)
*7 Front Speaker (Lime)
* If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”. See
the table below for connection details in accordance with the type of speaker you use.
TABLE for Audio Output Connection
Audio Output Channels Front Speaker Rear Speaker Central / Bass Side Speaker
(No. 7) (No. 4) (No. 5) (No. 3)
2 V -- -- --
4VV----
6VVV--
8VVVV
12
3
4
5
6
7
8
910
11
12
13
* To enable Multi-Streaming function, you need to connect a front panel audio cable to the front
panel audio header. After restarting your computer, you will find “Mixer” tool on your system.
Please select “Mixer ToolBox” , click “Enable playback multi-streaming”, and click
“ok”. Choose “2CH”, “4CH”, “6CH”, or “8CH” and then you are allowed to select “Realtek HDA
Primary output” to use Rear Speaker, Central/Bass, and Front Speaker, or select “Realtek HDA
Audio 2nd output” to use front panel audio.

1212
1212
12
2.2.
2.2.
2. InstallationInstallation
InstallationInstallation
Installation
AM2V890-VSTA is an ATX form factor (12.0-in x 8.0-in, 30.5 cm x 20.3 cm)
motherboard. Before you install the motherboard, study the configuration of your
chassis to ensure that the motherboard fits into it.
Pre-installation PrecautionsPre-installation Precautions
Pre-installation PrecautionsPre-installation Precautions
Pre-installation Precautions
Take note of the following precautions before you install motherboard
components or change any motherboard settings.
Before you install or remove any component, ensure that the
power is switched off or the power cord is detached from the
power supply. Failure to do so may cause severe damage to the
motherboard, peripherals, and/or components.
1. Unplug the power cord from the wall socket before touching any
component.
2. To avoid damaging the motherboard components due to static
electricity, NEVER place your motherboard directly on the carpet or
the like. Also remember to use a grounded wrist strap or touch a
safety grounded object before you handle components.
3. Hold components by the edges and do not touch the ICs.
4. Whenever you uninstall any component, place it on a grounded anti-
static pad or in the bag that comes with the component.
5. When placing screws into the screw holes to secure the motherboard
to the chassis, please do not over-tighten the screws! Doing so may
damage the motherboard.

1313
1313
13
2.12.1
2.12.1
2.1 CPU InstallationCPU Installation
CPU InstallationCPU Installation
CPU Installation
Step 1. Unlock the socket by lifting the lever up to a 90oangle.
Step 2. Position the CPU directly above the socket such that the CPU corner with
the golden triangle matches the socket corner with a small triangle.
Step 3. Carefully insert the CPU into the socket until it fits in place.
The CPU fits only in one correct orientation. DO NOT force the CPU
into the socket to avoid bending of the pins.
Step 4. When the CPU is in place, press it firmly on the socket while you push
down the socket lever to secure the CPU. The lever clicks on the side tab
to indicate that it is locked.
2.22.2
2.22.2
2.2 Installation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink
Installation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink
Installation of CPU Fan and Heatsink
After you install the CPU into this motherboard, it is necessary to install a
larger heatsink and cooling fan to dissipate heat. You also need to spray
thermal grease between the CPU and the heatsink to improve heat
dissipation. Make sure that the CPU and the heatsink are securely fas-
tened and in good contact with each other. Then connect the CPU fan to
the CPU FAN connector (CPU_FAN1, see Page 10, No. 3). For proper
installation, please kindly refer to the instruction manuals of the CPU fan
and the heatsink.
STEP 1:
Lift Up The Socket Lever
STEP 2 / STEP 3:
Match The CPU Golden Triangle
To The Socket Corner
STEP 4:
Push Down And Lock
The Socket Lever
Lever 90° Up CPU Golden Triangle
Socket Corner

1414
1414
14
2.3 Installation of Memory Modules (DIMM)2.3 Installation of Memory Modules (DIMM)
2.3 Installation of Memory Modules (DIMM)2.3 Installation of Memory Modules (DIMM)
2.3 Installation of Memory Modules (DIMM)
AM2V890-VSTA motherboard provides four 240-pinDDRII (Double Data Rate II)
DIMM slots, and supports Dual Channel Memory Technology. For dual channel
configuration, you always need to install identical (the same brand, speed,
size and chip-type)DDRII DIMM pair in the slots of the same color. In other words,
you have to install identical DDRII DIMM pair in Dual Channel A (DDRII_1 and
DDRII_2; Yellow slots; see p.10 No.6) or identical DDRII DIMM pair in Dual
Channel B (DDRII_3 andDDRII_4; Orange slots; see p.10 No.7), so that Dual
Channel Memory Technology can be activated. This motherboard also allows
you to install four DDRII DIMMs for dual channel configuration, and please install
identical DDRII DIMMs in all four slots. You may refer to the Dual Channel
Memory Configuration Table below.
Dual Channel Memory Configurations
DDRII_1 DDRII_2 DDRII_3 DDRII_4
(Yellow Slot) (Yellow Slot) (Orange Slot) (Orange Slot)
(1) Populated Populated - -
(2) - - Populated Populated
(3)* Populated Populated Populated Populated
* For the configuration (3), please install identicalDDRIIDIMMs in all four slots.
1. If you want to install two memory modules, for optimal compatibility
and reliability, it is recommended to install them in the slots of the
same color. In other words, install them either in the set of yellow
slots (DDRII_1 and DDRII_2), or in the set of orange slots (DDRII_3
and DDRII_4).
2. If only one memory module or three memory modules are installed
in the DDRII DIMM slots on this motherboard, it is unable to activate
the Dual Channel Memory Technology.
3. If a pair of memory modules is NOT installed in the same Dual
Channel, for example, installing a pair of memory modules in DDRII_1
and DDRII_3, it is unable to activate the Dual Channel Memory
Technology .
4. It is not allowed to install a DDR memory module into DDRII slot;
otherwise, this motherboard andDIMM may be damaged.

1515
1515
15
notch
break
notch
break
Installing a DIMMInstalling a DIMM
Installing a DIMMInstalling a DIMM
Installing a DIMM
Please make sure to disconnect power supply before adding or
removing DIMMs or the system components.
Step 1. Unlock a DIMM slot by pressing the retaining clips outward.
Step 2. Align aDIMM on the slot such that the notch on the DIMM matches the break
on the slot.
The DIMM only fits in one correct orientation. It will cause permanent
damage to the motherboard and theDIMM if you force the DIMM into the
slot at incorrect orientation.
Step 3. Firmly insert theDIMM into the slot until the retaining clips at both ends fully
snap back in place and the DIMM is properly seated.

1616
1616
16
2.42.4
2.42.4
2.4 Expansion Slots (PCI Slots and PCIE Slots)Expansion Slots (PCI Slots and PCIE Slots)
Expansion Slots (PCI Slots and PCIE Slots)Expansion Slots (PCI Slots and PCIE Slots)
Expansion Slots (PCI Slots and PCIE Slots)
There are 3 PCI slots and 3 PCI Express slots on AM2V890-VSTA motherboard.
PCI Slots: PCI slots are used to install expansion cards that have the 32-bit PCI
interface.
PCIE Slots: PCIE1 (PCIE x16 slot) is used for PCI Express cards with x16 lane
width graphics cards.
PCIE2 (PCIE x1 slot) is used for PCI Express cards with x1 lane width
graphics cards, such as Gigabit LAN card, SATA2 card, etc. Please
check the jumper settings on page 17 for different functions.
PCIE3 (PCIE x4 / x1 slot) is used for PCI Express cards with x4 / x1
lane width graphics cards. Please check the jumper settings on page
17 for different functions.
Installing an expansion cardInstalling an expansion card
Installing an expansion cardInstalling an expansion card
Installing an expansion card
Step 1. Before installing the expansion card, please make sure that the power
supply is switched off or the power cord is unplugged. Please read the
documentation of the expansion card and make necessary hardware
settings for the card before you start the installation.
Step 2. Remove the system unit cover (if your motherboard is already installed in
a chassis).
Step 3. Remove the bracket facing the slot that you intend to use. Keep the
screws for later use.
Step 4. Align the card connector with the slot and press firmly until the card is
completely seated on the slot.
Step 5. Fasten the card to the chassis with screws.
Step 6. Replace the system cover.

1717
1717
17
2.5 Dual Graphics Feature2.5 Dual Graphics Feature
2.5 Dual Graphics Feature2.5 Dual Graphics Feature
2.5 Dual Graphics Feature
This motherboard supports Dual Graphics Technology. When installing the add-on
VGA cards to this motherboard, you are allowed to choose two different ways to
decide the function of PCIE2 slot and PCIE3 slot. The default value of this feature is
to enable PCIE2 slot (PCI Express x1) and PCIE3 slot (PCI Express x1). You can also
adjust the jumpers according to the below table to disable PCIE2 slot and enable
PCIE3 slot (PCI Express x4). In other words, you are able to adjust the jumpers to
enjoy the benefit of Dual Graphics feature. Please refer to the table below for the
correct jumper settings.
3
2
1
2
J1
J1
Jumper Settings PCIE2 Slot PCIE3 Slot
PCIEx1 PCIE x1
(Default)
Disabled PCIE x4

1818
1818
18
+5V
1_2
+5VSB
2_3
Short Open
2-pin jumper
2.6 Jumpers Setup2.6 Jumpers Setup
2.6 Jumpers Setup2.6 Jumpers Setup
2.6 Jumpers Setup
The illustration shows how jumpers are
setup. When the jumper cap is placed on
pins, the jumper is “Short”. If no jumper cap
is placed on pins, the jumper is “Open”. The
illustration shows a 3-pin jumper whose pin1
and pin2 are “Short” when jumper cap is
placed on these 2 pins.
Jumper Setting
PS2_USB_PWR1 Short pin2, pin3 to enable
(see p.10, No. 1) +5VSB (standby) for PS/2
or USB wake up events.
Note: To select +5VSB, it requires 2 Amp and higher standby current provided
by power supply.
ClearCMOS
(CLRCMOS1, 2-pin jumper)
(see p.10, No. 9)
Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes
system setup information such as system password, date, time, and system
setup parameters. To clear and reset the system parameters to default setup,
please turn off the computer and unplug the power cord from the power
supply. After waiting for 15 seconds, use a jumper cap to short 2 pins on
CLRCMOS1 for 5 seconds.

1919
1919
19
2.7 Onboard Headers and Connectors2.7 Onboard Headers and Connectors
2.7 Onboard Headers and Connectors2.7 Onboard Headers and Connectors
2.7 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place jumper
caps over these headers and connectors. Placing jumper caps over the
headers and connectors will cause permanent damage of the motherboard!
FDDConnector
(33-pinFLOPPY1)
(see p.10,No. 21)
Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the
connector.
Primary IDE Connector (Blue) Secondary IDE Connector (Black)
(39-pinIDE1, see p.10, No. 13) (39-pinIDE2, see p.10, No. 14)
Note: If you use only one IDE device on this motherboard, please set the IDE
device as “Master”. Please refer to the instruction of your IDE device vendor
for the details. Besides, to optimize compatibility and performance, please
connect your hard disk drive to the primary IDE connector (IDE1, blue) and
CD-ROM to the secondary IDE connector (IDE2, black).
Serial ATA Connectors These two Serial ATA (SATA)
(SATA1: see p.10,No.17) connectors support SATA data
(SATA2: see p.10,No.15) cables for internal storage
devices. The current SATA
interface allows up to 1.5 Gb/s
data transfer rate.
Serial ATA (SATA) Either end of the SATA data
Data Cable cable can be connected to the
SATA hard disk or the SATA
connector on the motherboard.
SATA1
SATA2
FLOPPY1
Pin1
thered-stripedsideto Pin1
IDE1
PIN1
IDE2
PIN1
connect the black end
to the IDE devices
connect the blue end
to the motherboard
80-conductor ATA 66/100/133 cable

2020
2020
20
Serial ATA (SATA) Please connect the black end of
Power Cable SATA power cable to the power
(Optional) connector on the drive. Then
connect the white end of SATA
power cable to the power
connector of the power supply.
USB 2.0 Header This HD 8CH I/O provides you
(9-pin USB67) 4 ready-to-use USB 2.0 ports on
(see p.10, No. 10) the rear panel. If the rear USB
ports are not sufficient, this
USB 2.0 header is available to
support 2 extra USB 2.0 ports.
USB 2.0 Header This HD 8CH I/O provides you
(9-pinUSB45) 4 ready-to-use USB 2.0 ports on
(see p.10, No. 11) the rear panel. If the rear USB
ports are not sufficient, this
USB 2.0 header is available to
support 2 extra USB 2.0 ports.
Infrared Module Header This header supports an optional
(5-pin IR1) wireless transmitting and
(see p.10,No. 27) receiving infrared module.
Internal Audio Connector This connector allows you
(4-pin CD1) to receive stereo audio input
(CD1: see p.10, No. 31) from sound sources such as
a CD-ROM,DVD-ROM, TV
tuner card, or MPEG card.
Front PanelAudio Header This is an interface for the front
(9-pin HD_AUDIO1) panel audio cable that allows
(see p.10,No. 24) convenient connection and
control of audio devices.
connect to the SATA HDD
powerconnector
connect tothe
powersupply
USB_PWR
USB_PWR
P+7
P-7
P+6
P-6
GND
GND
DUMMY
1
1
IRTX
IRRX
GND
+5VSB
DUMMY
CD-L
GND
GND
CD-R
CD1
J_SENSE
OUT2_L
1
MIC_RET
PRESENCE#
GND
OUT2_R
MIC2_R
MIC2_L
OUT_RET
USB_PWR
USB_PWR
P+5
P-5
P+4
P-4
GND
GND
DUMMY
1