Assa Abloy Corbin Russwin ED8200 Series User manual

Installation Instructions
Copyright © 2011, 2020, ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
FM37 04/20
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
WARNING
This product can expose you to lead
which is known to the state of California
to cause cancer and birth defects or other
reproductive harm. For more information
go to www.P65warnings.ca.gov.
ED8200 Series
Low Profile Rim
Exit Devices

2
ED8200 Series
Installation Instructions
Low Profile Rim Exit Devices - Reversible
FM37 04/20
Copyright © 2011, 2020ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
TOC Table of Contents
1 Wood and Metal Door Prep. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
2 Spot and Drill Template Holes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
3 Insert Trim and Strike . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
4 Cutting Push Bar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
5 Mount Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
6 Test Push Bar and Dogging Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
7 Remove and Reinstall Cylinder in Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
8 Template . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
1 Wood and Metal Door Prep
a Mark Centerline
Establish the centerline of the device by drawing a
line across the door and stop 40-5/16” above the
floor.

3
ED8200 Series
Installation Instructions
Low Profile Rim Exit Devices - Reversible
FM37 04/20
Copyright © 2011, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
1 Wood and Metal Door Prep
b If your door has cylindrical lock cut-out for ANSI A115.2 and A115.3 Prep Doors
(Not for use with mullions.)
1. Extend horizontal and vertical
centerlines of cut out as shown at
right.
2. If frame has 5/8” stop, align
centerlines on template with
centerlines on door. Spot and drill
template holes as described above
and follow steps three through six.
3. If frame has 1/2” stop, align
centerlines on template with
centerlines on door and spot
mounting hols for LATCH ASSEMBLY
ONLY. The MOVE template up against
stop and spot mounting holes for
strike. Drill two mounting holes.
Now follow steps three thru six. Note
special shim shown at right, which
is mounted beneath strike. Shim
furnished only when ordered.
2 Spot and Drill Template Holes
Using template furnished, spot and drill mounting holes for trim (if furnished), device, and strike.
Caution: When installed with removable mullion, see instruction sheet packed with mullion. (Not
for use with ANSI prep.)
3 Install Trim and Strike
a Knob Trim
Caution: Refer to template packed with
trim before proceding with Step 3.
Caution: When using the ANSI cylinder
plate, the bosses on the latch assembly
must fit into the cutouts on the cylinder
plate so that the latch assembly lays flat
on the door.

4
ED8200 Series
Installation Instructions
Low Profile Rim Exit Devices - Reversible
FM37 04/20
Copyright © 2011, 2020ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
3 Install Trim and Strike, continued
a Knob Trim, continued
b Pull and Plate Trim
Caution: Refer to template packed with trim before proceding with Step 3.
Caution: When using the ANSI cylinder plate, the bosses on the latch assembly must fit into the
cutouts on the cylinder plate so that the latch assembly lays flat on the door.

5
ED8200 Series
Installation Instructions
Low Profile Rim Exit Devices - Reversible
FM37 04/20
Copyright © 2011, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
4 Cutting Push bar
5 Mount device

6
ED8200 Series
Installation Instructions
Low Profile Rim Exit Devices - Reversible
FM37 04/20
Copyright © 2011, 2020ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
6 Test Push Bar and Dogging Operation
No-Trim Series:
Latch bolt is retracted by the push bar inside.
Pull and Plate Trim Series:
Latch bolt is retracted by the push bar inside and the key outside. Turning the key in either direction
will retract the latch. Return key to the horizontal position to remove key and project latch.
Knob Trim Series:
Latch bolt is retracted by the push bar inside and the key or knob outside.
To lock knob: Insert key in cylinder and turn counterclockwise as far as the key will turn. Then return it
to its vertical position and withdraw key.
To unlock knob: Insert key in cylinder and turn clockwise as far as the key will turn (the latch will retract
during this procedure). Then return the key to its vertical position and withdraw key.
Dogging: Depress push bar. Insert dogging wrench and turn clockwise 90°. The push bar will remain
depressed and the latch will remain retracted.
7 To Remove and Reinstall Cylinder in Knob

7
ED8200 Series
Installation Instructions
Low Profile Rim Exit Devices - Reversible
FM37 04/20
Copyright © 2011, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Fold toward you on this
line and place this edge
against face of stop.
FOR LHR DOOR
Line up
with centerline
marked on
door
Strike For
Rim Device Only
KNOB TRIM
AND ANSI CUTOUT
(5/8" Stop)
FACE OF STOP
C
L
C
L
CYL
FOR RHR DOOR
Bore 2-1/8" dia. hole
thru door only for
functions with knob trim.
IF PULL OR PLATE TRIM with
cylinder is used. Drill 1-5/16"
dia hole thru door for cylinder.
IF CYLINDER only is used,
drill 1-5/16" hole from inside of
door and 1-9/16" hole 1/8"
deep from outside of door.
CYLINDER HOLE
CAUTION
When installed with
removable mullion,
see instruction sheet
packed with mullion.
1) For Pull or Plate Tr i m
2) For Knob Trim (standard) or no trim
REVIEW INSTALLATION FORM PACKED WITH DEVICE BEFORE USING THIS TEMPLATE
MOUNTING INSTRUCTIONS
Drill (2) 1/8" dia holes thru door.
Spot (2) screw hole locations for bracket screws.

Corbin Russwin is a brand associated with ASSA ABLOY Access and Egress Hardware Group, Inc., an ASSA ABLOY Group company.
Copyright © 2011, 2020, ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in part
without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Corbin Russwin, Inc.
225 Episcopal Road
Berlin, CT 06037 USA
Phone: [phone]
Fax: [phone]
www.corbinrusswin.com
FM37 04/20