AST Lighting COB MAX AST-CM0804-IP65 User manual

COB MAX SERIES
COB MAX LED STRIP
Code: AST-CM0804-IP65 SPEC SHEET
Features:
-Dow brand food grade silicon material: UV yellow resistant, safe and no odors.
-IP65 Silicon housing with sand blasted diffuser: dust less,dot less and soft light.
-Replacement for LED strip+aluminium profile that almost plug&play.
-Clips or 3M tape available for installation.
-Easy bending to ambient style.
Technical Specification
Light source parameters Electrical parameters
Mono Color 2400K/2700K/3000K/3500K
4000K/5000K/6500K/Red
Green/Blue/Amber/Pink
Input voltage 24VDC
Input current(5W/M) 0.21A/m
Colorful /Input current(10W/M) 0.42A/m
Input cable 15cm 20AWG
CRI (white color) 90+
SDCM (white color) <3
Operating parameters
Warranty 3 Years
Life span 50000 hrs
Storage temperature 0℃ ~ +60℃
Working temperature -20℃ ~ +40℃
Housing material Silicon glue
Waterproof rating IP65
Lumen&cut segment parameters
Color Lumen @(5watts/m) Lumen @(10watts/m) Cut segment
2000K/2400K/2700K/3000K
3500K/4000K/5000K/6500K 508 1015 50mm
Red(620-625nm）148 295 50mm
Green(515-525nm）518 1035 50mm
Blue(560-465nm）68 135 50mm
Amber( Yellow 585-595nm）163 325 50mm
Pink 303 605 50mm
*All datas are based on 1meter length ,±10% variant exists for above data
XIAMEN AST LIGHTING TECHNOLOGY CO., LTD www.astlighting.com 1/4

Dimension&bending parameters
Accessories options
Cable endcap Seal endcap Injection cable
endcap
Injection seal
endcap Clip
Installation guide
① The cutting mark is on the back of the strip
light.
② Please cut neatly according to the cutting
mark/
① Fix the clips on the wall by screw ② Push and fix the strip on the clips ③ Done
Above is installation way by clips. COB max is also available in 3M tape installation like the IP20 LED strip light.
XIAMEN AST LIGHTING TECHNOLOGY CO., LTD www.astlighting.com 2/4

Manual instruction
Wiring diagram
MONO
CCT
RGB
RGBW
XIAMEN AST LIGHTING TECHNOLOGY CO., LTD www.astlighting.com 3/4

Safety information
*The product is DC24V input, can only connect to the DC output of power supply.
*Powering the LED strip from 2 end by a unique power supply could reduce the voltage drop but can't use 2
different power supply
*Don’t overload the power supply unit.Usually most of the power supply has a efficiency between 80%-95%, so
when choosiing the power supply, the total watts of the strips should be smaller than 80% of the rate power of the
LED Strip Lights.
*Please use 24VDC isolated power supply to drive the led strip, and the constant voltage source ripple less than 5%. Can't
step-down the power by resistance-capacitance and nun-isolated power supply driver led strip, etc.
*The LED neon strip is DC low voltage input, can't connect to AC mains directly.
*Please don't light the LED Strip light before unreel, otherwise the product will overheat.
*Please clean the installation surface before attached the 3M type on.
*Please don't twist the strip light; hanging the light by power cable is not allowed; hanging the light by itself housing is not
allowed; step on the light is not allowed. folding the light is not allowed.
Applications
XIAMEN AST LIGHTING TECHNOLOGY CO., LTD www.astlighting.com 4/4