ASTM Functional Drawer User manual

1
Functional Drawer
Installation Manual
It may take 40 to 90mins for this assembly based on normal knowledge
Please prepare parts on a soft blanket against scratch and damage
The best helper is your patience, thanks for our developing team’s hundreds of hours
on DIY design
For future use for your baby , all painting has been tested to comply with ASTM safety
standard

2
Top Shelf
The tool kit is designed to be no harmful to your drawer, once you
remove this changer top, you wont see any visual holes when
you are standing in front of drawer.
Warning !!!
Do not leave baby unattended anytime on this changer top !
Please do not use it if your baby height is over changer size or upto 13month age !
This changer is not designed for permant use, just add function to your drawer
All surface including paint and pad is non-toxic
Independently tested to comply with ASTM safety standard
Independent Testing by Intertek

3
Front & Rear Panel (2 pcs)
A
C
Side Panels (2 pcs)
Bottom Panel (1 pc)
DChanging Pad (1 pc)
PARTS AND HARDWARES OF TOP SHELF
PHILLIPS--HEAD SCREWDRIVER REQUIRED
FOR ASSEMBLY ----NOT INCLUDE
STEP 1
A
B
Rods (8 pcs) Cam Locks (8 pcs)
23
B
A
B
2
2
2
2
3
3
3
3
Assemble 8pcs Rods (2) into the pre-drilled
holes on Front & Rear Panel (A) .
Tighten all Rods (2) by Phillips-head screwdriver .
Insert 8 pcs Cam Locks (3) into the pre-drilled
holes on the Side Panels (B) .

4
STEP 2
Slide Bottom Panel (C) into grooves of
Front & Rear Panel (A) and Side Panels
(B) .
PLEASE NOTE : Tighten all Cam Locks
(3) by phillips-head screwdriver .
C
A
A
B
B
HARDWARES OF CABINET
Rods (20 pcs) Cam Locks (20 pcs)
23
Wood Dowels 30mm
(23 pcs)
4Barrel Nuts (8 pcs)
6
Screws 40mm (6 pcs)1
Screws15mm (48 pcs)
7
Allen Head Bolts 90mm (8 pcs)
5
Allen Wrench (1 pc)
10
PHILLIPS--HEAD SCREWDRIVER REQUIRED
FOR ASSEMBLY ----NOT INCLUDE

5
PARTS LIST OF CABINET
Left Panel (1pc) Right Panel (1pc)
EF
Back Middle Connection (1 pc)
ISectional Panel Small (2pcs)
JK
Top Panel (1 pc)
LBottom Frame (1pc) Foot (5 pcs)
MN
Connection Panel (2 pc)
OBack Panel Small(1 pc ) Back Panel Big (1 pc)
PQ
Front Middle Connection with hole (1 pc)
G
Sectional Panel Big (1pc)
Front Middle Connection (1 pc)
H
H
G

6
STEP 1
Connect Front Middle Connection with hole (G)
and Back Middle Connection (I) to Sectional
Panel Big (K) by screws (1) and wood dowels
(4) .
Then tighten all by allen wrench (10) .
1
1
4
G
I
K
10
STEP 2
Connect Front Middle Connection with
hole (G) , Front Middle Connection (H)
to Left Panel (E) by 4pcs Rods (2) and
4pcs Cam Locks (3) .
Connect Back Middle Connection (I) to
Left Panel (E) by 1pc Rod (2) , 1pc Cam
Lock (3) and 1pc Wood Dowel (4) .
G
H
I
E
K
4
2
3
3
2
H
4
Put Front Middle Connection (H) in the gap of Sectional
Panel Big (K) by wood dowel(4) .

7
STEP 3
Connect Right Panel (F) to Front Middle
Connection with hole (G) , Front Middle
Connection (H) , Back Middle Connection
(I) use the same way as STEP 2 .
I
G
H
K
E
F
3
3
2
2
STEP 4
Lay down the assembled parts on a
soft blanket as shown .
Connect Bottom Frame (M) to Left
&Right Panel (E&F) by 6pcs wood
dowels (4) , 8pcs allen bolts (5)
8pcs barrel nuts (6) .
1.Assemble 4pcs wood dowels (4)
and 8pcs barrel nuts (6) into the
pre-drilled holes on Side Panel
(E&F) and Sectional Panel Big (K) .
2.Assemble 8pcs allen head bolts (5)
to the Barrel Nuts (6) through the
Bottom Frame (M) .
Then tighten the allen head bolts (5)
by allen wrench (10) .
M
E
F
10
5
5
6
4
5
5
6
66
6
K

8
STEP 5
Connect 5pcs Foot (N) to the Bottom
Frame (M) .
Then tighten them by hand .
N
NN
N
N
M
STEP 6
Connect Sectional Panel Small (J) to
Front&Back Middle Connection (G&I)
by screws (1) and wood dowels (4) .
Tighten by alllen wrench (10) .
G
J
J
I
1
1
1
1
4

9
STEP 7
Connect Top Panel (L) to Side Panel
(E&F) , Sectional Panel Small (J) by
10pcs rods (2) , 10pcs cam locks (3)
and 8pcs wood dowels (4) .
1.Assemble 10 pcs rods (2) into the
pre-drilled holes on Top Panel (L) ,
8pcs wood dowels (4) into the pre-
drilled holes on Side Panels (E&F)
and Sectional Panel Small (J) .
2.Assemble 10 pcs cam locks (3) into
the holes on Side Panels (E&F) and
Sectional Panel Small (J) .
Tighten all by phillips-head screwdriver .
3
3
3
3
2
4
L
J
J
F
E
Connect the assembled parts to the back
of chest using 36pcs screws (7) .
Tighten all by Phillips-head screwdriver .
PLEASE NOTE : Do not assemble the
screws on the three holes of top line as
shown .
STEP 8
P
Q
7
7
7
7

10
STEP 9
Connect Connection Panel (O) to
Rear Panel (A) , Top Panel (L)
by screws (7) .
Tighten all by Phillips-head screwdriver .
P
A
7L
PARTS AND HARDWARES OF SMALL DRAWER
a
Drawer Knobs (3 pcs)
14
Drawer Front Panels (3 pcs)
Drawer Left Side Panels (3 pcs)
Drawer Back Panels (3 pcs)
Drawer Bottom (3 pcs)
Drawer Right Side Panels (3 pcs)
b
d
e
a
b
c1
d
e
Screws 15mm (9 pcs)
13
Screws 40mm (24 pcs)1 Allen Wrench (1 pc)
10
PHILLIPS--HEAD SCREWDRIVER REQUIRED
FOR ASSEMBLY ----NOT INCLUDE
c1
O
L

11
a
b
c1
d
STEP 1
Connect Right Side Panel (c1) to Front Panel (a)
and Back Panel (d) using screw (1) .
Then tighten all by allen wrench (10) .
1
1
1
1
STEP 2
Slide Bottom Panel (e) into grooves of Front Panel (a) , Left & Right Side Panel
(b&c1) .
Connect Bottom Panel (e) to Back Panel (d) using 3pcs screws (13) .
Tighten by phillips-head screwdriver .
ee
a
b
d
e
ba
d
13
13
c1c1
Connect Left Side Panel (b) to Front Panel (a)
and Back Panel (d) using screw (1) .

12
STEP 3
Connect knob (14) to Front Panel (a)
Assemble another two drawers follow
step 1,2,3 .
a
a
b
c1
d
e
14
14
PARTS AND HARDWARES OF BIG DRAWER
fDrawer Front Panels (4 pcs)
Drawer Left Side Panels (4 pcs)
Drawer Back Panels (4 pcs)
Drawer Bottom (4 pcs)
Drawer Right Side Panels (4 pcs)
k
m
i
j
PHILLIPS--HEAD SCREWDRIVER REQUIRED
FOR ASSEMBLY ----NOT INCLUDE
f
k
m
i
j
Drawer Knobs (8 pcs)
14
Screws 15mm (16 pcs)
13
Screws 40mm (32 pcs)1 Allen Wrench (1 pc)
10

13
STEP 1
f
k
m
i
1
1
Connect Right Side Panel (m) to Front Panel (f)
and Back Panel (i) using screw (1) .
Then tighten all by allen wrench (10) .
1
1
STEP 2
13
13
13
13
f
k
m
i
f
k
m
j
Slide Bottom Panel (j) into grooves of Front Panel (f) , Left & Right Side Panel
(k&m
) .
Connect Bottom Panel (j) to Back Panel (i) using 4pcs screws (13) .
Tighten by phillips-head screwdriver .
j
i
Connect Left Side Panel (k) to Front Panel (f)
and Back Panel (i) using screw (1) .

14
STEP 3
j
i
f
k
m
14
14
f
Connect knob (14) to Front Panel (f)
Assemble another three drawers follow
step 1,2,3 .
Place Changing Pad (D) on the finished changing table .
You could use changing table safety .
D

15
Slide the drawers into rails on Side Panel (E&F) .