Asus S97V User manual

Disassembly procedure
2-1 V1.0
Disassembly Procedure
Please follow the information provided in this section to perform the complete
disassembly procedure of the notebook. Be sure to use proper tools described
before.
S97V/Z97V Notebook consists of various modules. This chapter
describes the procedures for the complete notebook disassembly. In addition, in between
procedures, the detailed disassembly procedure of individual modules will be provided for your
service needs.
The disassembly procedure consists of the following steps:
•Battery Module
•CPU Module
•VGA Module
•Memory Module
•WLAN Module
•TV Tuner
•HDD Module
•Optical Drive Module
•Keyboard Module
•Bottom Case Module
•Motherboard Module
•Top Case Module
•LCD Module
Chapter
2

Disassembly procedure
2-2 V1.0
Battery Module
The illustration below shows how to remove the battery module.
Remove Battery module
1．Slide the battery latch 1 to open battery lock
2．Slide the battery latch 2 and pull the whole battery out.
CPU Module
The illustrations below show how to remove the CPU module from the notebook.
Removing CPU module
1. Remove 3 screws (M2*6L) on CPU door and take the card reader away.
BATTERY
CPU MODULE
REMOVAL

Disassembly procedure
2-3 V1.0
2. Remove CPU door.
2. Disconnect the CPU fan cable and then thread the cable out as the arrow showed..
2. Remove 3 screws and take away the CPU fan from the system.
3. Remove 10 screws.

Disassembly procedure
2-4 V1.0
4. Take away the heat sink module.
5. Turn the non-removable screw here 180 degrees counter-clockwise to loosen the CPU.
6. Squeeze the vacuum handling pump on the CPU and use it to lift the CPU away.

Disassembly procedure
2-5 V1.0
VGA Module
The illustration shows how to remove the VGA module form the notebook.
Removing VGA module
1. Remove 2 screws to pop it up at 30 degree angles and then remove the VGA module.
VGA
REMOVAL

Disassembly procedure
2-6 V1.0
Memory Module
The illustration shows how to remove the memory module form the notebook.
Removing Memory module
1. Pull two latches here to pop the Memory module up at 45°angles, and then pull out the
module at that angle.
MEMORY
MODULE
MEMORY
REMOVAL

Disassembly procedure
2-7 V1.0
WLAN Module
The illustration below shows how to remove the WLAN module from the notebook.
Remove WLAN module
1. Disconnect the 2antennas here and then remove two screws to pop it up at 45 degree
angles and then pull it out at that angle.
TV Tuner Module
The illustrations below show how to remove the TV Tuner module from the notebook.
Removing HDD Module
1. Remove 2 screws and take away TV Tuner.
WLAN
MODULE
WLAN
MODULE
REMOVAL
TV TUNER
MODULE
TV TUNER
MODULE
REMOVAL

Disassembly procedure
2-8 V1.0
2. Disconnect the following cables (modem cable、speaker cable、touchpad-fingerprint
cable、Bluetooth cable )with motherboard.
3. Remove 1 screw and disconnect USB board cable with motherbaord.
HDD Module
The illustrations below show how to remove the HDD module from the notebook.
Removing HDD Module
1. Remove 2 screws here.
HDD
MODULE
HDD
MODULE
REMOVAL
TFcable
BT cable
S
p
eaker cable
MD cable

Disassembly procedure
2-9 V1.0
2. Pull the hard disk module toward the direction of the arrow and then lift it up and take it
out.
3. Remove 4 screws to separate HDD from HDD housing.
4. Remove 2 screws to separate HDD bracket from HDD bezel.

Disassembly procedure
2-10 V1.0
Optical Drive Module
1. Push the ODD module softly and slowly pull the ODD module out.
Keyboard Module
The illustrations below show how to remove the keyboard.
Removing Keyboard
1. Open 4 latches (Esc, F5, F10 and Pause) on keyboard module.
2. Turn over the keyboard plate and disconnect the keyboard FPC, and then remove the
keyboard plate.
OPTICAL
DRIVE
REMOVAL
KEYBOAR

Disassembly procedure
2-11 V1.0
Removing Keyboard Cable
1. Use a flexible connector tool to unlock the cable connector on both ends (no. 1).
2. Carefully pull out the keyboard cable (no. 2) with a pair of tweezers.
3. Lock the connector (no. 3) again to avoid possible breakage.
Bottom Case Module
The illustrations below show how to disassemble and remove the bottom case module of the notebook.
The module contains the bottom case itself.
1. Dismount hinge covers and take it away.
BOTTOM CASE
REMOVAL
1. Unlock
2. Cable out
3.
1. Unlock
3.

Disassembly procedure
2-12 V1.0
2. Remove 2 screws.
3. Put the WLAN antennas through the hole of bottom case and disconnect the two cables
here.
4. Remove 4 screws here on bottom case fastening hinges.
LVDS cable
INVERTER cable

Disassembly procedure
2-13 V1.0
5. Remove dummy card and separate LCD module from the bottom case orderly.
6. Remove 4 screws and take away the left bottom case.
7. Disconnect Bluetooth cable and take it away by hand.

Disassembly procedure
2-14 V1.0
8. Unscrew 9 screws and take away the right bottom case.
Motherboard module
The illustrations below show how to disassemble and remove the Motherboard
module
1. Remove 4 screws and remove motherboard.
2. Remove 2 screws and remove the IO bracket.
THERBOARD
MODULE

Disassembly procedure
2-15 V1.0
3. Tear off 3 tapes.
4. Disconnect modem cable with motherboard.
5. Remove 2 screws and take it away.

Disassembly procedure
2-16 V1.0
Top Case Module
The illustrations below show how to disassemble and remove the top case module of the notebook.
The module contains the top case itself.
Removing Top Case Module
1. Tear 1 piece of tape here and disconnect touchpad-fingerprint cable with touchpad.
2. Disconnect touchpad-fingerprint cable with fingerprint board.
TOP CASE
REMOVAL

Disassembly procedure
2-17 V1.0
3. Disconnect touchpad-fingerprint-motherboard cable with fingerprint board.
4. Remove 4 screws on fingerprint module and remove it.
5. Remove 2 screws on fingerprint board and separate it with its bracket.
6. Remove 2 screws and take away the Launch board.

Disassembly procedure
2-18 V1.0
7. Remove 1 screw and disconnect the USB board-Launch board cable..
8. Disconnect USB board-motherboard cable with USB board, then take it away.
9. Remove 2 screws and take away the cover, then remove the USB board-Launch board
cable.

Disassembly procedure
2-19 V1.0
10. Tear off 5 tapes and remove the USB board-motherboard cable.
11. Tear off 2 tapes.
12. Remove 4 screws.

Disassembly procedure
2-20 V1.0
13. Remove the 2 speakers.
LCD Module
The illustrations below show how to remove and disassemble the LCD module. The
module contains LCD panel, Inverter board, LCD bezel, LCD back cover.
Disassembling LCD Module
1. Remove 6 rubber pads and 6 screws on LCD front bezel.
2. Pry the inside edges softly to separate LCD front bezel from LCD panel and take it away.
LCD MODULE
L
CD MODULE
ISASSEMBLY