Asus V2-AE1 User manual

Vintage2-AE1
Barebone System

iiii
iiii
ii
Copyright © 2005 ASUSTeK COMPUTER INC. All Rights Reserved.Copyright © 2005 ASUSTeK COMPUTER INC. All Rights Reserved.
Copyright © 2005 ASUSTeK COMPUTER INC. All Rights Reserved.Copyright © 2005 ASUSTeK COMPUTER INC. All Rights Reserved.
Copyright © 2005 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form
or by any means, except documentation kept by the purchaser for backup purposes, without the
express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or
altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the
serial number of the product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS
OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR
ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND
SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY
OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered
trademarks or copyrights of their respective companies, and are used only for identification or
explanation and to the owners’ benefit, without intent to infringe.
E2207E2207
E2207E2207
E2207
First Edition V1First Edition V1
First Edition V1First Edition V1
First Edition V1
November 2005November 2005
November 2005November 2005
November 2005

iiiiii
iiiiii
iii
Table of contents
Notices ................................................................................................ vi
Safety information ............................................................................. vii
About this guide ............................................................................... viii
System package contents ................................................................... x
Chapter 1: System introductionChapter 1: System introduction
Chapter 1: System introductionChapter 1: System introduction
Chapter 1: System introduction
1.1 Welcome! .............................................................................. 1-2
1.2 Front panel ........................................................................... 1-3
1.3 Rear panel ............................................................................. 1-4
1.4 Internal components ............................................................ 1-6
Chapter 2:Chapter 2:
Chapter 2:Chapter 2:
Chapter 2: Basic installationBasic installation
Basic installationBasic installation
Basic installation
2.1 Preparation ........................................................................... 2-2
2.2 Before you proceed .............................................................. 2-2
2.3 Removing the side cover and front panel assembly ............. 2-3
2.4 Central Processing Unit (CPU) .............................................. 2-4
2.4.1 Overview ................................................................. 2-4
2.4.2 Installling the CPU ................................................... 2-4
2.4.3 Installing the CPU fan and heatsink assembly ........ 2-6
2.5 Installing a DIMM ................................................................... 2-8
2.5.1 Memory configurations ........................................... 2-8
2.5.3 Removing a DIMM ................................................. 2-11
2.5.2 Installing a DIMM ................................................... 2-11
2.6 Expansion slots ................................................................... 2-12
2.6.1 Installing an expansion card .................................. 2-12
2.6.2 Configuring an expansion card.............................. 2-13
2.6.3 PCI slots ................................................................ 2-14
2.6.4 PCI Express x1 slot ............................................... 2-14
2.6.5 AGP 8X slot .......................................................... 2-14
2.6.6 Wireless LAN module (optional) ........................... 2-15
2.7 Installing storage drives ..................................................... 2-16
2.7.1 Optical drive ......................................................... 2-16
2.7.2 Floppy disk drive ................................................... 2-17
2.7.3 Hard disk drive ...................................................... 2-18
2.8 Connecting cables .............................................................. 2-19
2.9 Removing the bay covers ................................................... 2-20
2.10 Reinstalling the front panel assembly and side cover ........ 2-20

iviv
iviv
iv
Table of contents
Chapter 3:Chapter 3:
Chapter 3:Chapter 3:
Chapter 3: Starting upStarting up
Starting upStarting up
Starting up
3.1 Installing an operating system ............................................. 3-2
3.2 Powering up .......................................................................... 3-2
3.3 Support CD information ........................................................ 3-2
3.3.1 Drivers menu .......................................................... 3-3
3.3.2 Utilities menu .......................................................... 3-4
3.3.3 Make Disk menu ...................................................... 3-5
3.3.4 Manuals menu ......................................................... 3-6
3.3.5 ASUS Contact information ...................................... 3-7
3.3.6 Other information ................................................... 3-7
3.4 Software information ........................................................... 3-9
3.4.1 ASUS PC Probe II ..................................................... 3-9
3.4.2 Cool ‘n’ Quiet!™ Technology ................................. 3-16
3.4.3 ASUS Update utility .............................................. 3-18
3.4.4 ASUS MyLogo™ ..................................................... 3-21
5.3.5 Using the Wireless LAN module ............................ 3-23
Chapter 4:Chapter 4:
Chapter 4:Chapter 4:
Chapter 4: Motherboard infoMotherboard info
Motherboard infoMotherboard info
Motherboard info
4.1 Motherboard information ...................................................... 4-2
4.2 Jumpers ................................................................................ 4-3
4.3 Connectors ........................................................................... 4-6
4.3.1 Rear panel connectors ............................................ 4-6
4.3.2 Internal connectors ................................................. 4-6
Chapter 5:Chapter 5:
Chapter 5:Chapter 5:
Chapter 5: BIOS setupBIOS setup
BIOS setupBIOS setup
BIOS setup
5.1 Managing and updating your BIOS ........................................ 5-2
5.1.1 Creating a bootable floppy disk .............................. 5-2
5.1.2 ASUS EZ Flash utility .............................................. 5-3
5.1.3 AFUDOS utility ........................................................ 5-4
5.1.4 ASUS CrashFree BIOS 2 utility ................................ 5-6
5.2 BIOS setup program ............................................................. 5-8
5.2.1 BIOS menu screen ................................................... 5-9
5.2.2 Menu bar ................................................................. 5-9
5.2.3 Navigation keys ...................................................... 5-9
5.2.4 Menu items ........................................................... 5-10

vv
vv
v
Table of contents
5.2.5 Sub-menu items ................................................... 5-10
5.2.6 Configuration fields .............................................. 5-10
5.2.7 Pop-up window ..................................................... 5-10
5.2.8 Scroll bar .............................................................. 5-10
5.2.9 General help .......................................................... 5-10
5.3 Main menu .......................................................................... 5-11
5.3.1 System Time ......................................................... 5-11
5.3.2 System Date ......................................................... 5-11
5.3.3 Legacy Diskette A ................................................ 5-11
5.3.4 Primary, Secondary, Third, and Fourth IDE
Master/Slave ........................................................ 5-12
5.3.5 System Information .............................................. 5-13
5.4 Advanced menu .................................................................. 5-14
5.4.1 JumperFree Configuration .................................... 5-14
5.4.2 USB Configuration ................................................. 5-15
5.4.3 CPU Configuration ................................................. 5-16
5.4.4 Chipset ................................................................. 5-17
5.4.5 Onboard Devices Configuration ............................ 5-24
5.4.6 PCI PnP ................................................................. 5-25
5.5 Power menu ........................................................................ 5-26
5.5.1 Suspend Mode ...................................................... 5-26
5.5.2 Repost Video on S3 Resume ................................ 5-26
5.5.3 ACPI 2.0 Support .................................................. 5-26
5.5.4 ACPI APIC Support ................................................ 5-26
5.5.5 APM Configuration ................................................ 5-27
5.5.6 Hardware Monitor ................................................. 5-29
5.6 Boot menu .......................................................................... 5-30
5.6.1 Boot Device Priority .............................................. 5-31
5.6.2 Boot Settings Configuration ................................. 5-31
5.6.3 Security ................................................................ 5-33
5.7 Exit menu ........................................................................... 5-35

vivi
vivi
vi
Notices
Federal Communications Commission StatementFederal Communications Commission Statement
Federal Communications Commission StatementFederal Communications Commission Statement
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with
manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Canadian Department of Communications StatementCanadian Department of Communications Statement
Canadian Department of Communications StatementCanadian Department of Communications Statement
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.This class B digital apparatus complies with Canadian ICES-003.
This class B digital apparatus complies with Canadian ICES-003.This class B digital apparatus complies with Canadian ICES-003.
This class B digital apparatus complies with Canadian ICES-003.
WARNING!WARNING!
WARNING!WARNING!
WARNING! The use of shielded cables for connection of the monitor to
the graphics card is required to assure compliance with FCC regulations.
Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to
operate this equipment.

viivii
viivii
vii
Safety information
Electrical safetyElectrical safety
Electrical safetyElectrical safety
Electrical safety
• To prevent electrical shock hazard, disconnect the power cable from the
electrical outlet before relocating the system.
• When adding or removing devices to or from the system, ensure that the
power cables for the devices are unplugged before the signal cables are
connected.
• If the power supply is broken, do not try to fix it by yourself. Contact a
qualified service technician or your retailer.
Operation safetyOperation safety
Operation safetyOperation safety
Operation safety
• Before installing devices into the system, carefully read all the
documentation that came with the package.
• Before using the product, make sure all cables are correctly connected
and the power cables are not damaged. If you detect any damage,
contact your dealer immediately.
• To avoid short circuits, keep paper clips, screws, and staples away from
connectors, slots, sockets and circuitry.
• Avoid dust, humidity, and temperature extremes. Do not place the
product in any area where it may become wet. Place the product on a
stable surface.
• If you encounter technical problems with the product, contact a qualified
service technician or your retailer.
Lithium-Ion Battery WarningLithium-Ion Battery Warning
Lithium-Ion Battery WarningLithium-Ion Battery Warning
Lithium-Ion Battery Warning
CAUTIONCAUTION
CAUTIONCAUTION
CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the
manufacturerís instructions.
VORSICHTVORSICHT
VORSICHTVORSICHT
VORSICHT: Explosionsgetahr bei unsachgemäßen Austausch der
Batterie. Ersatz nur durch denselben oder einem vom Hersteller
empfohlenem ähnljchen Typ. Entsorgung gebrauchter Batterien nach
Angaben des Herstellers.
LASER PRODUCT WARNINGLASER PRODUCT WARNING
LASER PRODUCT WARNINGLASER PRODUCT WARNING
LASER PRODUCT WARNING
CLASS 1 LASER PRODUCTCLASS 1 LASER PRODUCT
CLASS 1 LASER PRODUCTCLASS 1 LASER PRODUCT
CLASS 1 LASER PRODUCT

viiiviii
viiiviii
viii
About this guide
AudienceAudience
AudienceAudience
Audience
This guide provides general information and installation instructions about
the ASUS Vintage2-AE1 barebone system. This guide is intended for
experienced users and integrators with hardware knowledge of personal
computers.
How this guide is organizedHow this guide is organized
How this guide is organizedHow this guide is organized
How this guide is organized
This guide contains the following parts:
1.1.
1.1.
1. Chapter 1: System introductionChapter 1: System introduction
Chapter 1: System introductionChapter 1: System introduction
Chapter 1: System introduction
This chapter gives a general description of the barebone system. The
chapter presents the system features including introduction on the
front and rear panel, and internal components.
2.2.
2.2.
2. Chapter 2: Basic installationChapter 2: Basic installation
Chapter 2: Basic installationChapter 2: Basic installation
Chapter 2: Basic installation
This chapter provides step-by-step instructions on how to install
components in the system.
3.3.
3.3.
3. Chapter 3: Starting upChapter 3: Starting up
Chapter 3: Starting upChapter 3: Starting up
Chapter 3: Starting up
This chapter helps you power up the system and install drivers and
utilities from the support CD.
4.4.
4.4.
4. Chapter 4: Motherboard informationChapter 4: Motherboard information
Chapter 4: Motherboard informationChapter 4: Motherboard information
Chapter 4: Motherboard information
This chapter gives information about the motherboard that comes
with the system. This chapter includes the motherboard layout,
jumper settings, and connector locations.
5.5.
5.5.
5. Chapter 5: BIOS informationChapter 5: BIOS information
Chapter 5: BIOS informationChapter 5: BIOS information
Chapter 5: BIOS information
This chapter tells how to change system settings through the BIOS
Setup menus and describes the BIOS parameters.

ixix
ixix
ix
Conventions used in this guideConventions used in this guide
Conventions used in this guideConventions used in this guide
Conventions used in this guide
WARNING:WARNING:
WARNING:WARNING:
WARNING: Information to prevent injury to yourself when
trying to complete a task.
CAUTION:CAUTION:
CAUTION:CAUTION:
CAUTION: Information to prevent damage to the components
when trying to complete a task.
IMPORTANT:IMPORTANT:
IMPORTANT:IMPORTANT:
IMPORTANT: Instructions that you MUST follow to complete a
task.
NOTE:NOTE:
NOTE:NOTE:
NOTE: Tips and additional information to aid in completing a
task.
Where to find more informationWhere to find more information
Where to find more informationWhere to find more information
Where to find more information
Refer to the following sources for additional information and for product
and software updates.
1.1.
1.1.
1. ASUS WebsitesASUS Websites
ASUS WebsitesASUS Websites
ASUS Websites
The ASUS websites worldwide provide updated information on ASUS
hardware and software products. Refer to the ASUS contact
information.
2.2.
2.2.
2. Optional DocumentationOptional Documentation
Optional DocumentationOptional Documentation
Optional Documentation
Your product package may include optional documentation, such as
warranty flyers, that may have been added by your dealer. These
documents are not part of the standard package.

xx
xx
x
System package contents
Check your Vintage2-AE1 system package for the following items.
If any of the items is damaged or missing, contact your retailer
immediately.
1.1.
1.1.
1. ASUS Vintage2-AE1 barebone systemASUS Vintage2-AE1 barebone system
ASUS Vintage2-AE1 barebone systemASUS Vintage2-AE1 barebone system
ASUS Vintage2-AE1 barebone system with
• ASUS motherboard
• 300 W PFC power supply unit
• ASUS chassis
• Front panel I/O board
• Wireless module (optional)
2.2.
2.2.
2. CableCable
CableCable
Cable
• AC power cable
3.3.
3.3.
3. Support CDSupport CD
Support CDSupport CD
Support CD
4.4.
4.4.
4. User guideUser guide
User guideUser guide
User guide

ASUS Vintage2-AE1ASUS Vintage2-AE1
ASUS Vintage2-AE1ASUS Vintage2-AE1
ASUS Vintage2-AE1
Chapter 1
System introduction
This chapter gives a general
description of the barebone
system. The chapter presents the
system features including
introduction on the front and rear
panel, and internal components.

1-21-2
1-21-2
1-2 Chapter 1: System introductionChapter 1: System introduction
Chapter 1: System introductionChapter 1: System introduction
Chapter 1: System introduction
1.1 Welcome!
Thank you for choosing the ASUS Vintage2-AE1!
The ASUS Vintage2-AE1 is an all-in-one barebone system with a powerful
computing capability, expandability, and versatile connectivity.
The system comes in a stylish mini-tower casing and powered by the ASUS
motherboard. The system motherboard supports the latest AMD Athlon™
64/64FX, and Sempron™ desktop processors in the 939-pin package.
Two DDR DIMM slots support up to 2 GB of system memory using
DDR400/333 DIMMs. The system also provides a choice of high-resolution
graphics via an integrated graphics controller or via an AGP card
(purchased separately).
The system also supports the PCI Express technology with a PCI Express x1
slot, and features a host of storage and connectivity including Serial ATA
support, USB 2.0, and 5.1-channel audio capability. As an option, you may
also choose to avail of the system’s capability to support a wireless module
that allows you to share data and media files minus the hassle of wires.
With Vintage2-AE1, you are ahead in the world of power computing.

1-31-3
1-31-3
1-3
ASUS Vintage2-AE1ASUS Vintage2-AE1
ASUS Vintage2-AE1ASUS Vintage2-AE1
ASUS Vintage2-AE1
1.1.
1.1.
1. 5.25-inch drive bay cover5.25-inch drive bay cover
5.25-inch drive bay cover5.25-inch drive bay cover
5.25-inch drive bay cover. Covers two 5.25-inch bays for optical
drives.
2.2.
2.2.
2. 3.5-inch drive bay cover3.5-inch drive bay cover
3.5-inch drive bay cover3.5-inch drive bay cover
3.5-inch drive bay cover. Covers two 3.5-inch bays for a hard
disk and a floppy disk drive.
3.3.
3.3.
3. USB 2.0 portsUSB 2.0 ports
USB 2.0 portsUSB 2.0 ports
USB 2.0 ports. These Universal Serial Bus 2.0 (USB 2.0) ports are
available for connecting USB 2.0 devices such as a mouse, printer,
scanner, camera, PDA, and others.
4.4.
4.4.
4. Microphone portMicrophone port
Microphone portMicrophone port
Microphone port. This Mic (pink) +port connects a microphone.
5.5.
5.5.
5. Headphone portHeadphone port
Headphone portHeadphone port
Headphone port. This Line In (green) port connects a headphone
with a stereo mini-plug.
6.6.
6.6.
6. Hard disk drive activity LED.Hard disk drive activity LED.
Hard disk drive activity LED.Hard disk drive activity LED.
Hard disk drive activity LED.
7.7.
7.7.
7. Power buttonPower button
Power buttonPower button
Power button. Press this button to turn the system on.
8.8.
8.8.
8. Reset buttonReset button
Reset buttonReset button
Reset button. Press this button to reboot the system without
turning off the power.
1.2 Front panel
The front panel includes the optical drive bays, floppy disk drive slot, power
button, and several I/O ports are located at the front panel.
22
22
2
11
11
1
77
77
7
88
88
8
66
66
6
33
33
3
44
44
4
55
55
5

1-41-4
1-41-4
1-4 Chapter 1: System introductionChapter 1: System introduction
Chapter 1: System introductionChapter 1: System introduction
Chapter 1: System introduction
1.3 Rear panel
The system rear panel includes the power connector and several I/O ports
that allow convenient connection of devices.
1.1.
1.1.
1. Power connector.Power connector.
Power connector.Power connector.
Power connector. This connector is for the power cable and plug.
2.2.
2.2.
2. Voltage selector.Voltage selector.
Voltage selector.Voltage selector.
Voltage selector. This switch allows you to adjust the system
input voltage according to the voltage supply in your area. See the
next section before adjusting this selector.
3.3.
3.3.
3. PS/2 mouse portPS/2 mouse port
PS/2 mouse portPS/2 mouse port
PS/2 mouse port. This green 6-pin connector is for a PS/2 mouse.
4.4.
4.4.
4. PS/2 keyboard portPS/2 keyboard port
PS/2 keyboard portPS/2 keyboard port
PS/2 keyboard port. This purple 6-pin connector is for a
PS/2 keyboard.
5.5.
5.5.
5. Serial portSerial port
Serial portSerial port
Serial port . This port connects a mouse, modem, or other devices
that conforms with serial specification.
6.6.
6.6.
6. Parallel port.Parallel port.
Parallel port.Parallel port.
Parallel port. This 25-pin port connects a printer, scanner, or other
devices.
7.7.
7.7.
7. VGA port.VGA port.
VGA port.VGA port.
VGA port. This port connects a VGA monitor.
8.8.
8.8.
8. USB 2.0 ports 1, 2, 3 and 4.USB 2.0 ports 1, 2, 3 and 4.
USB 2.0 ports 1, 2, 3 and 4.USB 2.0 ports 1, 2, 3 and 4.
USB 2.0 ports 1, 2, 3 and 4. These 4-pin Universal Serial Bus
(USB) ports are available for connecting USB 2.0 devices.
9.9.
9.9.
9. Microphone port (pink).
Microphone port (pink).
Microphone port (pink).Microphone port (pink).
Microphone port (pink). This port connects a microphone.
10.10.
10.10.
10. Line Out port (lime).Line Out port (lime).
Line Out port (lime).Line Out port (lime).
Line Out port (lime). This port connects a headphone or a speaker.
11.11.
11.11.
11. Line In port (light blue).Line In port (light blue).
Line In port (light blue).Line In port (light blue).
Line In port (light blue). This port connects the tape, CD, DVD
player, or other audio sources.
11
11
133
33
3
11
11
144
44
4
1515
1515
15
11
11
166
66
6
11
11
144
44
4
11
11
177
77
7
11
11
122
22
2
11
11
1
22
22
2
33
33
3
44
44
4
55
55
5
66
66
6
77
77
7
88
88
8
99
99
9
11
11
111
11
1
1010
1010
10

1-51-5
1-51-5
1-5
ASUS Vintage2-AE1ASUS Vintage2-AE1
ASUS Vintage2-AE1ASUS Vintage2-AE1
ASUS Vintage2-AE1
Refer to the audio configuration table below for the function of the
audio ports in 2, 4, or 6-channel configuration.
Audio 2, 4, or 6-channel configurationAudio 2, 4, or 6-channel configuration
Audio 2, 4, or 6-channel configurationAudio 2, 4, or 6-channel configuration
Audio 2, 4, or 6-channel configuration
Light Blue Line In Line In Line In
Lime Line Out Front Speaker Out Front Speaker Out
Pink Mic In Mic In Mic In
PortPort
PortPort
Port HeadsetHeadset
HeadsetHeadset
Headset 4-channel4-channel
4-channel4-channel
4-channel 6-channel6-channel
6-channel6-channel
6-channel
2-channel2-channel
2-channel2-channel
2-channel
12.12.
12.12.
12. Expansion slot metal bracketsExpansion slot metal brackets
Expansion slot metal bracketsExpansion slot metal brackets
Expansion slot metal brackets. Covers the expansion card slots.
Remove the metal bracket only when installing an expansion card.
13.13.
13.13.
13. Power supply unit fan vent.Power supply unit fan vent.
Power supply unit fan vent.Power supply unit fan vent.
Power supply unit fan vent. This vent is for the PSU fan that
provides ventilation inside the power supply unit.
14.14.
14.14.
14. Cover screws.Cover screws.
Cover screws.Cover screws.
Cover screws. Secure the side cover to the chassis.
15.15.
15.15.
15. Chassis fan vent.Chassis fan vent.
Chassis fan vent.Chassis fan vent.
Chassis fan vent. This vent is for the fan that provides ventilation
inside the system chassis.
16.16.
16.16.
16. LAN (RJ-45) port.LAN (RJ-45) port.
LAN (RJ-45) port.LAN (RJ-45) port.
LAN (RJ-45) port. This port allows Gigabit connection to a Local
Area Network (LAN) through a network hub.
17.17.
17.17.
17. Metal bracket lock.Metal bracket lock.
Metal bracket lock.Metal bracket lock.
Metal bracket lock. Secures the expansion card metal bracket to
the chassis.
Setting the switch to 115 V in a 230 V environment or 230 V in a
115 V environment will seriously damage the system!
Selecting the voltageSelecting the voltage
Selecting the voltageSelecting the voltage
Selecting the voltage
The system’s power supply unit has a
115 V/230 V voltage selector switch
located beside the power connector.
Use this switch to select the
appropriate system input voltage
according to the voltage supply in your
area.
If the voltage supply in your area is
100-127 V, set the switch to 115 V.
If the voltage supply in your area is
200-240 V, set the switch to 230 V.

1-61-6
1-61-6
1-6 Chapter 1: System introductionChapter 1: System introduction
Chapter 1: System introductionChapter 1: System introduction
Chapter 1: System introduction
1.4 Internal components
The illustration below is the internal view of the system when you remove
the top cover and the power supply unit. The installed components are
labeled for your reference. Proceed to Chapter 2 for instructions on
installing additional system components.
1. Front panel cover
2. 5.25-inch optical drive bays
3. Hard disk drive bay
4. Floppy disk drive bay
5. Power supply unit
6. CPU socket
7. DIMM sockets
8. ASUS motherboard
9. Chassis fan
10. AGP slot
11. PCI Express x1 slot
12. PCI slots
13. Metal bracket lock
PCI1
A8V-MQ
BIOS
Flash
ROM
ALC653
USBPW56
USBPW78
CHA_FAN
USB56
PCI2
AGP
PANEL
ATX12V
CPU_FAN
Super
I/O
FP_AUDIO
DDR DIMM_B1 (64 bit,184-pin module)
EATXPWR
SATA 2
FLOPPY
SEC_IDE
Socket 939
CR2032 3V
Lithium Cell
CMOS Power
VIA
VT8251
VIA
K8M800
PCIEX1
PS/2KBMS
T: Mouse
B: Keyboard
Below:Mic In
Center:Line Out
Top:Line In
USB12
LAN_USB34
COM1
PARALLEL PORT
VGA
DDR DIMM_A1 (64 bit,184-pin module)
SATA 1
SATA 4
SATA 3
PRI_IDE
USB78
USBPW12
USBPW34
KBPWR
AUX CD
CLRTC SB_PWR
SPDIF
CHASSIS
RTL8201CL
BUZZER
22
22
2
11
11
1
11
11
133
33
3
33
33
3
66
66
6
1212
1212
12
88
88
8
55
55
5
99
99
944
44
4
1010
1010
10
11
11
111
11
1
77
77
7

ASUS Vintage2-AE1ASUS Vintage2-AE1
ASUS Vintage2-AE1ASUS Vintage2-AE1
ASUS Vintage2-AE1
Chapter 2
Basic installation
This chapter provides step-by-step
instructions on how to install
components in the system.

2-22-2
2-22-2
2-2 Chapter 2: Basic installationChapter 2: Basic installation
Chapter 2: Basic installationChapter 2: Basic installation
Chapter 2: Basic installation
2.1 Preparation
Before you proceed, make sure that you have all the components you plan
to install in the system.
Basic components to install:Basic components to install:
Basic components to install:Basic components to install:
Basic components to install:
1. Central processing unit (CPU)
2. DDR Dual Inline Memory Module (DIMM)
3. Expansion card(s)
4. Hard disk drive
5. Optical drive
6. Floppy disk drive
ToolTool
ToolTool
Tool
Phillips (cross) screw driver
2.2 Before you proceed
Take note of the following precautions before you install components into
the system.
• Use a grounded wrist strap or touch a safely grounded object or a
metal object, such as the power supply case, before handling
components to avoid damaging them due to static electricity.
• Hold components by the edges to avoid touching the ICs on them.
• Whenever you uninstall any component, place it on a grounded
antistatic pad or in the bag that came with the component.
The motherboard comes with an onboard standby power LED. This LED
lights up to indicate that the system is ON, in sleep mode or in soft-off
mode, and not powered OFF. Unplug the power cable from the power outlet
and make sure that the standby power LED is OFF before installing any
system component.
®
Onboard LED
SB_PWR
ON
Standby
Power
OFF
Powered
Off

2-32-3
2-32-3
2-3
ASUS Vintage2-AE1ASUS Vintage2-AE1
ASUS Vintage2-AE1ASUS Vintage2-AE1
ASUS Vintage2-AE1
2.3 Removing the side cover and
front panel assembly
1. Remove the cover screws on the rear panel.
2. Pull the side cover toward the rear panel until its hooks disengage
from the chassis. Set the side cover aside.
3. Locate the front panel assembly hooks, then lift them until they
disengage from the chassis.
4. Swing the front panel assembly to the right, until the hinge-like tabs
on the right side of the assembly are exposed.
5. Remove the front panel assembly, then set aside.
11
11
1
Air ductAir duct
Air ductAir duct
Air duct
11
11
1
22
22
2
22
22
2
33
33
3
44
44
4
HookHook
HookHook
Hook
Hinge-like tabHinge-like tab
Hinge-like tabHinge-like tab
Hinge-like tab

2-42-4
2-42-4
2-4 Chapter 2: Basic installationChapter 2: Basic installation
Chapter 2: Basic installationChapter 2: Basic installation
Chapter 2: Basic installation
2. Unlock the socket by pressing the lever
sideways, then lift it up to a 90°-100°
angle.
Make sure that the socket lever is
lifted up to 90°-100° angle, otherwise
the CPU does not fit in completely.
2.4.22.4.2
2.4.22.4.2
2.4.2 Installling the CPUInstallling the CPU
Installling the CPUInstallling the CPU
Installling the CPU
To install a CPU:
1. Locate the CPU socket on the motherboard.
2.4 Central Processing Unit (CPU)
2.4.12.4.1
2.4.12.4.1
2.4.1 OverviewOverview
OverviewOverview
Overview
The motherboard comes with a surface mount 939-pin Zero Insertion Force
(ZIF) socket designed for the AMD Athlon™ 64/64FX or Sempron™
processor.
The 128-bit-wide data paths of these
processors can run applications faster
than processors with only 32-bit or 64-bit
wide data paths.
Take note of the marked corner (with gold
triangle) on the CPU. This mark should
match a specific corner on the socket to
ensure correct installation.
Vintage2-AE1 does not support dual-core processors.
Gold triangleGold triangle
Gold triangleGold triangle
Gold triangle
®
CPU Socket 939