AT&T ID102 User manual

Music Dock for iPhone®and iPod® Devices
coolBlu
user’s
manual
model #: ID102

Page 2
hello.
What’s Included
Page 3
Unpack the docking station and make sure all accessories are put aside so
they will not be lost.
Thank you for purchasing
coolBlu [ ID102].
Music Dock For iPhone®and iPod® Devices
iPhone®and iPod®are registered trademarks of Apple Inc.
Features
· Speaker dock for iPhone and iPod device
· FM radio
· Alarm clock
· Built in stereo speaker
· Line-In Jack for use with other devices
· Play & charge your iPhone and iPod device simultaneously
AC Adapter
Docking Station
Dock Adapters
iPhone/iPod devices

Page 4
Introduction
What’s Included
Safety Information
Getting Started
Location of Main Unit Controls
Power Supply
Back Up Batteries
Preparation for Use
Dock Adapters
Operational Instructions
Dimmer Function
Setting the Digital Clock
Alarm Functions
Electronic Volume Control
Radio Operation
Operation with iPhone and iPod Device
Music Equalizer
Using the Audio Line in Connection (AUX-INPUT)
Troubleshooting
Compliance with FCC Regulations
Warranty Information
Specifications
2
3
5
8
9
9
9
10
11
11
12
14
15
16
17
17
18
19
20
21
Page 5
Contents Safety Information
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO DRIPPING OR SPLASHING LIQUIDS.
Warning!
NOTES: Caution symbols are printed on rear of unit.
Please refer to user’s manual.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the condition that this device does
not cause harmful interference.
The lightning flash
and arrowhead
symbol within the
triangle is a warning
sign alerting you of
“dangerous voltage”
inside the product.
CAUTION
WARNING: To reduce
the risk of electric
shock, do not remove
cover (or back). No
user-serviceable parts
inside. Refer servicing
to qualified service
personnel.
The exclamation
point within the
triangle is a warning
sign alerting you
of important
instructions
accompanying the
product.
RISK OF ELECTRIC
SHOCK DO NOT OPEN

Safety Information
Page 6
Safety Information
Page 7
11. LIGHTNING -Unplug the unit from the wall outlet and disconnect
the antenna or cable system during a lightning storm or when it is left
unattended and unused for long periods of time. This will prevent damage
to the product due to lightning and power-line surges.
12.OVERLOADING -Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or electric shock.
13.HEAT -The unit should be situated away from heat sources such as
radiators, heat registers, stoves or other appliances (including amplifiers)
that produce heat.
14.DAMAGE REQUIRING SERVICE -The unit should be serviced by qualified
service personnel when:
A. the power supply cable or plug has been damaged.
B. objects have fallen into or liquid has been spilled onto the enclosure.
C. the unit has been exposed to rain.
D. the unit has been dropped or the enclosure damaged.
E. the unit exhibits a marked change in performance or does not operate
normally.
15. SERVICING -The user should not attempt to service the unit beyond those
methods described in the user’s manual. Opening or removing covers will
expose you to dangerous voltage and other hazards. Service methods
not covered in the user’s manual should be referred to qualified service
personnel.
16.SAFETY CHECK -Upon completion of any service or repair to the unit,
ask the service technician to perform safety checks to determine that the
product is in proper working condition.
Important Safety Instructions
1. CLEANING -Unplug the unit from the wall outlet before cleaning. Clean the
unit using a damp cloth; do not use liquid or aerosol cleaners.
2. ATTACHMENTS -Do not use attachments not recommended by the
manufacturer.
3. ANTENNA -Do not connect an external antenna to the unit (other than that
provided).
4. WATER AND MOISTURE -The unit should not be used near water. For
example: near a bathtub, washbowl, kitchen sink, laundry tub, swimming
pool or in a wet basement.
5. PLACEMENT -Do not place the unit on an unstable table, stand, tripod, or
bracket. This may result in serious personal injuries and damage to the unit.
6. VENTILATION -The unit should be situated so that its location or position
does not interfere with its proper ventilation. For example, it should not be
situated on a bed, sofa, rug or similar surface that may block ventilation
openings. Also, it should not be placed in a built-in installation, such as
a bookcase or cabinet, which may impede the flow of air through the
ventilation openings.
7. PERIODS OF NON-USE -If the unit is to be left unused for an extended
period of time, such as a month or longer, the power cable should be
unplugged from the unit to prevent damage or corrosion.
8. OBJECTS AND LIQUID ENTRY -Care should be taken so that external
objects do not fall into and liquids are not spilled onto any openings or vents
located on the product.
9. POWER SOURCE -The unit should be connected to a power supply only of
the type described in the operating instructions or as marked on the unit. If
you are not sure please consult the dealer or local power company.
10.POWER CORD PROTECTION -Power supply cord should be routed so that
it is not likely to be walked on or pinched by items placed upon or against it.
It is always better to have a clear area from where the cable exits the unit to
where it is plugged into an AC outlet.
When used in the directed manner, this unit has been designed and
manufactured to ensure your personal safety. However, improper use can
result in potential electrical shock or fire hazards. Please read all safety and
operating instructions carefully before installation and use, and keep these
instructions handy for future reference. Take special note of all warnings listed
in this user’s manual and on the unit.

Getting Started
Page 9
Getting Started
Page 8
Location of Main Unit Controls
1. Speaker
2. Blue backlit display
3. Back-up battery compartment
(Bottom of docking station)
4. Cavity for dock adaptor
5. Dock adaptor for iPod device
(Several different adaptors are
provided)
6. VOLUME DOWN ( - ) button
  MEMORY
AL-MODEFUNC.
EQ
7. VOLUME UP ( + ) button
  MEMORY
AL-MODEFUNC.
EQ
8. MEMORY button
9. EQ/SLEEP button
1
2
3
17
18
19
4
710
5
8
11
69
12 13 14 15
16
Front View
Back View
Top View
6~16 buttons
10. ON/OFF button
  MEMORY
AL-MODEFUNC.
EQ
11. SKIP ( - )/SEARCH ( - ) button
  MEMORY
AL-MODEFUNC.
EQ
12. SKIP ( + )/SEARCH ( + ) button
  MEMORY
AL-MODEFUNC.
EQ
13. AL-MODE/AL-SET button
14. FUNCTION/CL-SET button
15. PLAY/PAUSE/STEREO/MONO button
  MEMORY
AL-MODEFUNC.
EQ
16. SNOOZE/DIMMER button
17. AUX-INPUT socket
18. DC jack (DC 6V + )
19. FM antenna wire
Power Supply
AC Operation (External AC-DC Power Adaptor)
- coolBlu is equipped with a “DC-jack” that should only be used with the
supplied AC-adapter to operate the docking station. Use of other adaptors
may damage the docking station or cause it to malfunction.
- Plug the tail end of the AC-adaptor into the DC-jack (socket) on the rear of
the docking station.
- Insert the plug of the AC-adaptor into a wall outlet with AC-power and not
controlled by a wall switch.
- Press the
  MEMORY
AL-MODEFUNC.
EQ
button to switch on the docking station.
- coolBlu is designed to operate without ever being totally powered “OFF”. It
will either be “ON” or in “STANDBY” mode.
- In “STANDBY” mode, the blue backlit digital display will be dimmed, but the
display will show the current time (clock function).
- From “STANDBY” mode, you can switch “ON” the docking station by
pressing the
  MEMORY
AL-MODEFUNC.
EQ
button.
- Save energy by switching the system to “STANDBY” mode when not in use.
Back Up Batteries
- Open the battery door at the bottom of docking station.
- Insert 2 “AAA” batteries (not included) in the battery compartment. The 2
batteries supply backup power for the current time clock and radio memory
preset stations during brief power outages.
Preparation for Use
- Before connecting your iPhone/iPod device to coolBlu, it is recommended
to insert the proper dock adapter for your iPhone/iPod device model.
coolBlue includes dock adaptors that work with several models of iPhone
device and iPod device.
- If you want to connect a different model iPhone/iPod device at a later time,
you can easily remove the dock adaptor from your speaker system using a
fingernail, and insert the adaptor that fits the new iPod device.

Page 11
Getting Started
Page 10
Dock Adapters
Choose the dock adapter that fits your iPhone/iPod device and insure your
iPhone/iPod device fits snugly into the correct adapter.
iPhone
iPhone 3G
iPhone 3Gs
iPhone 4
iPod
5th generation
(video)
30GB
60GB
80GB
iPod nano
5th generation
(video camera)
8GB
16GB
iPod nano
4th generation
(video)
8GB
16GB
iPod classic
80GB
120GB
160GB
iPod touch
4th generation
8GB
32GB
64GB
iPod touch
1th generation
2nd generation
3rd generation
14
16
OR
10
OR
9
10
OR
9
17
1820
19
OR
15
the dock adaptor
number shows which
iPhone/iPod device fits.
Operational Instructions
Dimmer Function
coolBlu has a dimmer function to adjust the brightness level of the display
backlight to reduce eye strain and save energy. Simply adjust as desired by
pressing the SNOOZE/DIMMER button repeatedly (hi-dimmer/low-dimmer/
OFF). The display backlight will always return to low-dimmer after reset of the
docking station.
Setting the Digital Clock
Press the button to turn the docking station into “STANDBY” mode. In
“STANDBY” mode, the display will continuously show the current time.
In this situation the blue backlight is normally dimmed to save electricity.
Switch docking station to “STANDBY”
mode (display light = dimmed)
Correct time is now set & will be
shown on the display.
Press & hold the FUNC./CL-SET button for 3 seconds.
Display shows “12H” Hour or “24H” hour (flashing)
Press the
  MEMORY
AL-MODEFUNC.
EQ
or
  MEMORY
AL-MODEFUNC.
EQ
button to select 12-hour or 24-hour clock display system & press the
FUNC./CL-SET button to confirm your selection
Press the
  MEMORY
AL-MODEFUNC.
EQ
or
  MEMORY
AL-MODEFUNC.
EQ
button repeatedly to set the correct hour in the display & press the
FUNC./CL-SET button to confirm
Press the
  MEMORY
AL-MODEFUNC.
EQ
or
  MEMORY
AL-MODEFUNC.
EQ
button repeatedly to set the correct minute in the display & press the
FUNC./CL-SET button to confirm
How to Set the Correct Time

Page 13Page 12
Operational Instructions
Alarm Function
coolBlu is equipped with 3 alarm modes: buzzer, radio and iPod. Before
setting the alarm, make sure to set the clock (see “Digital Clock Function” on
page 11) .
Alarm Time Setting
1. Please make sure the docking station is in “STANDBY” mode. (LED clock
dimmed)
2. Press the
  MEMORY
AL-MODEFUNC.
EQ
button to put the docking station into “STANDBY” mode (blue
backlight dimmed).
3. Press and hold AL-MODE/AL-SET button until the
hour digits on the display are flashing.
4. 4. Press the
  MEMORY
AL-MODEFUNC.
EQ
or
  MEMORY
AL-MODEFUNC.
EQ
button to reach the hour of the
desired WAKE UP time; then press AL-MODE/AL-
SET button to confirm. The display will now show
the minute digits flashing.
5. Press the
  MEMORY
AL-MODEFUNC.
EQ
or
  MEMORY
AL-MODEFUNC.
EQ
button to reach the minutes of the
desired WAKE UP time, then press the AL-MODE/AL-SET button
to confirm.
6. Select the desired source that the docking station will play at the “WAKE
UP” time.:
Press the
  MEMORY
AL-MODEFUNC.
EQ
button to switch on the docking station (display blue light will
be “ON”).
Operational Instructions
1. For iPhone or iPod : Connect the iPhone device or iPod device to the docking station. Select
the song or the desired playlist to play at the “WAKE UP” time. Start and
pause playback of the song/playlist at the point from which you want
playback to begin at the “WAKE UP” time.
For radio : Tune in the desired station.
For buzzer : No preparation is required.
2. Adjust the volume level as desired by pressing
  MEMORY
AL-MODEFUNC.
EQ
or
  MEMORY
AL-MODEFUNC.
EQ
button. Once the desired source
has been prepared, press the
  MEMORY
AL-MODEFUNC.
EQ
button to put the docking station into standby mode. Press
the AL-MODE/AL-SET button repeatedly to select the source as desired. The AL(buzz)/iPod/
FM lights flash in sequence until the desired source is selected.
00:00
:0
0
7:00
7:
7
12:00
FM
AL
iPod
Alarm time
Alarm symbol
Flashing FM symbol Flashing iPod symbol
3. Hour (Flashing)
4. Minutes (Flashing)
00:00
:0
0
7:00
7:
7
12:00
FM
AL
iPod
Alarm time
Alarm symbol
Flashing FM symbol Flashing iPod symbol
7. The alarm time is now fully programmed and the alarm symbol will appear
to indicate that the alarm function is “ACTIVE”.
8. The docking station will now automatically switch “ON” at the wake up time
you have chosen, as long as the alarm function is “ACTIVE”.
9. To turn off the docking station after it has automatically switched on,
simply press the button once. This will switch off the docking station but
will not clear the alarm settings. The docking station will switch on again
automatically on the next day at exactly the same preset time.
10.To deactivate the alarm, press continuously the AL-MODE/AL-SET button
until symbol “AL” disappears from the display.
11. To activate the alarm again, repeat the procedure of “ALARM TIME
SETTING”.
If the alarm is set to iPod, you need to make certain the iPhone
device or iPod device is connected properly and using docking
station power rather than the battery power of the device.
Otherwise, the buzzer alarm will sound at the set time.
important!

Page 15Page 14
Operational Instructions
Snooze Function
- When the alarm rings, it can be temporarily suspended for a short period of
9 minutes, by pressing the SNOOZE/DIMMER button once. In this period,
you will observe “AL” icon flashing on the display.
- The alarm will then automatically come on again after the 9 minute
“SNOOZE” period has ended.
- The procedure can be repeated for approximately 90 minutes from original
alarm wake up time.
Automatic Power Off Sleep Function
- coolBlu has a special sleep function which, when set, will automatically
switch the docking station off after a preset amount of time. This is useful
for sleeping to music at night.
- At any time while the docking station is operating, press & hold the EQ/
SLEEP button until the “SL” symbol flashes. Press the EQ/SLEEP button
repeatedly to choose the desired automatic power off time. In this period,
you will observe “SL” icon on the display.
Operational Instructions
90
mins
80
mins
20
mins
10
mins OFF*
* OFF means sleep timer is deactivated
Electronic Volume Control
- To increase or decrease the loudness of coolBlu, press the
  MEMORY
AL-MODEFUNC.
EQ
or
  MEMORY
AL-MODEFUNC.
EQ
button
respectively.
- Release the button when the desired volume level is reached.
- Sometimes, especially when listening to the radio, you may notice a “click-
click-click” (repeating) sound when you are increasing or decreasing the
volume. This is a normal condition & the sound will disappear when you
release the volume button.
Radio Operation
- Press the
  MEMORY
AL-MODEFUNC.
EQ
button to turn the docking station on.
- Press the FUNC./CL-SET button repeatedly until the display shows “FM”.
- Extend and adjust the FM-wire antenna to obtain the best reception.
- Use the
  MEMORY
AL-MODEFUNC.
EQ
button to select the desired mode (stereo/mono). In stereo
mode, you will observe “ST” icon on the display. Whereas in mono, no icon is
observed on the display.
- In some cases where reception is poor, it may be advisable to select
“MONO” mode to improve clarity of the radio signal.
Manual Station Adjustment (Scan Mode)
- Press (and immediately release) the
  MEMORY
AL-MODEFUNC.
EQ
and
  MEMORY
AL-MODEFUNC.
EQ
buttons to “scan” (manually
adjust) the radio stations “up” or “down” 1-frequency at a time.
- The digital display will indicate the exact station at each step’s position.
- When a desired station is reached, it can be saved into one of the
“MEMORY” positions. (See “RADIO MEMORY” section below.)
Automatic Station Adjustment (Seek Mode)
- Press and hold (for 2 seconds) the
  MEMORY
AL-MODEFUNC.
EQ
and
  MEMORY
AL-MODEFUNC.
EQ
buttons to automatically “seek”
the radio stations “up” or “down” to the next available station in your area.
- The digital display will indicate the exact frequency of the next station that
is found.
- When a desired station is reached, it can be saved into one of the
“MEMORY” positions. (See “RADIO MEMORY” section below.)
Radio Memory (Station Preset Memory Storage)
- At any time, the currently displayed station or frequency can be stored into
one of the memory positions.
- Press and hold the MEMORY button until “c01” flashes in the display.
- Press the
  MEMORY
AL-MODEFUNC.
EQ
and
  MEMORY
AL-MODEFUNC.
EQ
buttons to select desired memory position. (There are a
total of 30 memory positions.)
- Press the MEMORY button once to save the selected station into the
selected memory position.
- To recall any station saved to memory, simply press the memory button
once and use the
  MEMORY
AL-MODEFUNC.
EQ
and
  MEMORY
AL-MODEFUNC.
EQ
buttons to navigate your preset stations.
- To clear the memory of any position, simply save a new station to the same
memory position.

Operational Instructions Operational Instructions
Music Equalizer
At anytime during playback, press the EQ/SLEEP button repeatedly to choose
the desired sound effect according to the music you are listening to :
Using the Audio Line in Connection (AUX-INPUT)
- You can connect the audio input of an external device, such as a MP3 player
or a TV, to coolBlu for listening to the sound of that device through the high
quality amplifier of the docking station.
- To connect the external device, use a standard stereo headphone (3.5 mm)
cable. Connect the “headphone-out” or “audio line-out” of the device to
the aux-input socket of this docking station.
- Switch on the docking station and the external device (eg. MP3-player or
TV).
- Switch the function to aux using the FUNC./CL-SET button.
- Start playback of the external device and adjust the volume control of the
docking station to the desired level.
- Remember to switch off the docking station when you are finished using
the external device.
Operation with iPhone or iPod Device
- Turn on the docking station and the iPhone device or iPod device.
- Insert the iPhone device or iPod device into the docking station.
- Press the FUNC./CL-SET button repeatedly until the display shows “iPod”.
- Press the
  MEMORY
AL-MODEFUNC.
EQ
button on the docking station to begin playback.
- The iPhone/iPod display will indicate the information of the current song.
- At anytime during playback, press the
  MEMORY
AL-MODEFUNC.
EQ
button to pause playback. Press
  MEMORY
AL-MODEFUNC.
EQ
button to resume playback of the same song and position.
- At anytime during playback, press and release the
  MEMORY
AL-MODEFUNC.
EQ
and
  MEMORY
AL-MODEFUNC.
EQ
buttons to skip
forward or backwards by one song, as desired.
- At anytime during playback, press and hold the
  MEMORY
AL-MODEFUNC.
EQ
and
  MEMORY
AL-MODEFUNC.
EQ
buttons to fast-
forward (cue) or fast-reverse (review) the current song.
- You can operate the iPhone/iPod device using either the docking station’s
buttons, or directly with the iPhone/iPod device itself.
- When your iPhone/iPod device is connected to the docking station, it will
start charging the battery of the iPhone/iPod device.
- It is recommended that playback of your iPhone/iPod device be paused
before removing it from the docking station to prevent damage to your
song files.
Page 17Page 16
“Made for iPhone” and “made for iPod”, means that an electronic accessory has been designed to
connect specifically to iPhone and iPod respectively, and has been certified by the developer to meet
Apple performance standards. Apple is not responsible for the operation of this device or its compliance
with safety and regulatory standards. Please note that the use of this accessory with iPhone and iPod
may affect wireless performance.
E-0 = EQ OFF E•1 = CLASSIC
E•4 = POP
E•2 = JAZZ
E•3 = ROCK

Troubleshooting
Page 18
Remarks:
If troubleshooting does not eliminate the problem, disconnect the DC IN plug from the back of
docking station and reconnect it after a few seconds. This resets the docking station to it’s factory
default settings and results in the deletion of all previous settings. In case the problem still exists, see
warranty information on page 20 to obtain service.
Compliance with FCC Regulations
Page 19
The equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate Radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to Radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to Radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced Radio/television technician for
assistance.
THE SPECIFICATION AND EXTERNAL APPEARANCE OF THE MUSIC DOCK
ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE.
If at any time in the future you should need to dispose
of this product, please note that waste electrical
products should not be disposed of with household
waste. Please recycle where facilities exist. Check with
your local authority or retailer for recycling advice.
Symptom
coolBlu does not
respond
(no power)
iPhone/iPod device
does not dock properly
iPhone/iPod device
does not respond to
the coolBlu
iPhone/iPod device is
not charging
Possible cause
AC adapter is not plugged into a wall
outlet or the connector is not plugged
into the DC IN jack on the back of the
docking station.
iPhone/iPod device is not installed
properly.
iPhone/iPod device is not installed
properly.
iPhone/iPod device is not installed
properly.
iPhone/iPod device is locked up/
frozen.
iPhone/iPod battery has a problem.
iPhone/iPod device is locked up/
frozen.
Using first or second generation iPod,
iPod shuffle or other devices.
Using no or wrong iPhone/iPod dock
adapter.
Solution
Verify the AC adapter is plugged into
wall outlet and the DC IN jack properly.
Remove the iPhone/iPod devicefrom
the docking station and check for
obstruction on the connections of the
docking station and of the iPhone/iPod
device. Then reset the iPhone/iPod
device into the docking station.
Remove the iPhone/iPod devicefrom
the docking station and check for
obstruction on the connections of the
docking station and of the iPhone/iPod
device. Then reset the iPhone/iPod
device into the docking station.
Remove the iPhone/iPod devicefrom
the docking station and check for
obstruction on the connections of the
docking station and of the iPhone/iPod
device. Then reset the iPhone/iPod
device into the docking station.
Make sure your iPhone/iPod device
is working properly before docking it
into the docking station. Please refer
to the iPhone/iPod device manual for
details.
Make sure your iPhone/iPod device
is working properly before docking it
into the docking station. Please refer
to the iPhone/iPod device manual for
details.
coolBlu cannot control these
iPod devices or other devices.
Make sure the dock adapter is the
proper fit for the iPhone/iPod device.