AT&T 3G MicroCell User manual

AT&T 3G MicroCell™
Q
u
ic
k
St
ar
t
Status Indicators (Front of the Device)
Computer
Ethernet
Power
Getting To Know Your Device
Package Contents
AT&T 3G MicroCell™ | AC power adapter | Yellow ethernet cable | Quick Start | User Guide
To view an activation tutorial, visit att.com/3GMicroCell under the “Help“ tab.
Power
Ethernet
GPS
Computer
3G
Before You Begin
Serial Number (S/N) Tip
Write down your MicroCell’s serial number; you’ll
need it for online activation and future reference.
It can be found on the bottom of the device or on
the box label.
Serial # (S/N)
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and
other countries. A listing of Cisco’s trademarks can be found at www.cisco.com/go/trademarks. Third-party
trademarks mentioned are the property of their respective owners. The use of the word partner does not imply
a partnership relationship between Cisco and any other company. AT&T, the AT&T logo, and AT&T 3G MicroCell
are trademarks of AT&T Knowledge Ventures. Product and service availability is subject to change without notice.
Portions © AT&T Intellectual Property. Portions © Cisco and/or its affiliates. All rights reserved.
February 2012 Part Number 4038348 Rev B
Having Trouble?
1. Have you waited at least 90 minutes?
2. Have you activated your MicroCell online and received the
Online Activation Complete email?
3. Does your MicroCell have a solid GPS light?
4. Is your Internet connection and home network up and
running and connected?
Need More Help?
Refer to the Troubleshooting section in the User Guide,
visit att.com/3GMicroCell-Help,or call AT&T Support at
1-800-331-0500.
• Plan your installation location – your device should be:
– Within three feet of a window to receive a GPS signal for 911 purposes.
– At least one foot away from other wireless broadcasting devices to avoid possible interference.
– Where you can connect your MicroCell to your Internet equipment.
• Plan on 10-15 minutes for equipment setup and online activation. Your device will then need up to
an additional 90 minutes for final device activation, which requires no effort on your part.
• You will need your AT&T wireless phone number/user name or AT&T Access ID, as well as your
password for online activation. If you haven’t set up an AT&T online wireless account, you can do
so while activating your MicroCell online.

AT&T 3G MicroCell™
Q
u
ic
k
St
ar
t
Status Indicators (Front of the Device)
Computer
Ethernet
Power
Getting To Know Your Device
Package Contents
AT&T 3G MicroCell™ | AC power adapter | Yellow ethernet cable | Quick Start | User Guide
To view an activation tutorial, visit att.com/3GMicroCell under the “Help“ tab.
Power
Ethernet
GPS
Computer
3G
Before You Begin
Serial Number (S/N) Tip
Write down your MicroCell’s serial number; you’ll
need it for online activation and future reference.
It can be found on the bottom of the device or on
the box label.
Serial # (S/N)
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and
other countries. A listing of Cisco’s trademarks can be found at www.cisco.com/go/trademarks. Third-party
trademarks mentioned are the property of their respective owners. The use of the word partner does not imply
a partnership relationship between Cisco and any other company. AT&T, the AT&T logo, and AT&T 3G MicroCell
are trademarks of AT&T Knowledge Ventures. Product and service availability is subject to change without notice.
Portions © AT&T Intellectual Property. Portions © Cisco and/or its affiliates. All rights reserved.
February 2012 Part Number 4038348 Rev B
Having Trouble?
1. Have you waited at least 90 minutes?
2. Have you activated your MicroCell online and received the
Online Activation Complete email?
3. Does your MicroCell have a solid GPS light?
4. Is your Internet connection and home network up and
running and connected?
Need More Help?
Refer to the Troubleshooting section in the User Guide,
visit att.com/3GMicroCell-Help,or call AT&T Support at
1-800-331-0500.
• Plan your installation location – your device should be:
– Within three feet of a window to receive a GPS signal for 911 purposes.
– At least one foot away from other wireless broadcasting devices to avoid possible interference.
– Where you can connect your MicroCell to your Internet equipment.
• Plan on 10-15 minutes for equipment setup and online activation. Your device will then need up to
an additional 90 minutes for final device activation, which requires no effort on your part.
• You will need your AT&T wireless phone number/user name or AT&T Access ID, as well as your
password for online activation. If you haven’t set up an AT&T online wireless account, you can do
so while activating your MicroCell online.

AT&T 3G MicroCell™
Q
u
ic
k
St
ar
t
Status Indicators (Front of the Device)
Computer
Ethernet
Power
Getting To Know Your Device
Package Contents
AT&T 3G MicroCell™ | AC power adapter | Yellow ethernet cable | Quick Start | User Guide
To view an activation tutorial, visit att.com/3GMicroCell under the “Help“ tab.
Power
Ethernet
GPS
Computer
3G
Before You Begin
Serial Number (S/N) Tip
Write down your MicroCell’s serial number; you’ll
need it for online activation and future reference.
It can be found on the bottom of the device or on
the box label.
Serial # (S/N)
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and
other countries. A listing of Cisco’s trademarks can be found at www.cisco.com/go/trademarks. Third-party
trademarks mentioned are the property of their respective owners. The use of the word partner does not imply
a partnership relationship between Cisco and any other company. AT&T, the AT&T logo, and AT&T 3G MicroCell
are trademarks of AT&T Knowledge Ventures. Product and service availability is subject to change without notice.
Portions © AT&T Intellectual Property. Portions © Cisco and/or its affiliates. All rights reserved.
February 2012 Part Number 4038348 Rev B
Having Trouble?
1. Have you waited at least 90 minutes?
2. Have you activated your MicroCell online and received the
Online Activation Complete email?
3. Does your MicroCell have a solid GPS light?
4. Is your Internet connection and home network up and
running and connected?
Need More Help?
Refer to the Troubleshooting section in the User Guide,
visit att.com/3GMicroCell-Help,or call AT&T Support at
1-800-331-0500.
• Plan your installation location – your device should be:
– Within three feet of a window to receive a GPS signal for 911 purposes.
– At least one foot away from other wireless broadcasting devices to avoid possible interference.
– Where you can connect your MicroCell to your Internet equipment.
• Plan on 10-15 minutes for equipment setup and online activation. Your device will then need up to
an additional 90 minutes for final device activation, which requires no effort on your part.
• You will need your AT&T wireless phone number/user name or AT&T Access ID, as well as your
password for online activation. If you haven’t set up an AT&T online wireless account, you can do
so while activating your MicroCell online.

NOTE: Some mobile devices will display items differently.
Connect your device to the Internet
Connect the yellow ethernet cable from the
“Ethernet” port on your MicroCell to your router.
Quick Setup
(If you don’t have a router, see User Guide page 9.)
Visit att.com/3GMicroCell-Activate
and follow the instructions on the screen.
You’ll need the following:
» Serial number (S/N)—it’s on the bottom of the
device and the box label.
» Your AT&T wireless phone number/user name or AT&T
Access ID, as well as your password. If you haven’t set up
an AT&T online wireless account, you’ll need to do so.
Power on your device
Activate your device online
Connect your MicroCell to a power outlet
with the AC power adapter.
The Power light on the front of the device will come on
immediately. Within a few minutes, other lights will flash
as a GPS signal is located and software is updated.
NOTE:
Hold on to this guide;
you’ll come back to
it after you activate
your device.
www
Take a break!
You will receive a text message and email once
activation is complete.
Visit att.com/3GMicroCell to learn more on how to
get the most out of your MicroCell.
Wait while your device connects
NOTE:
It can take up to 90
minutes to complete
activation. Your
device may update
and restart during
this time.
The GPS and 3G lights will start
flashing GREEN after connecting
power to your device. Solid GREEN
indicates activation is complete!
3G Status Confirmation
Confirm your success
Your device is configured and working
properly when:
» You receive a text message and an email confirmation.
» The 3G light on your MicroCell is solid and GREEN.
» Your cell phone shows “AT&T MicroCell” or “AT&T
M-Cell” instead of “AT&T” as the network provider
(as shown below).
NOTE:
You may need to
restart your cell
phone for “AT&T
MicroCell” or “AT&T
M-Cell” to appear.
14
25
3
AT&T AT&T MicroCell AT&T M-Cell
or
Power
Solid Green
Ethernet
Solid Green
GPS
Solid Green
Computer
3G
Solid Green
Proceed to Step 4 if you completed online activation at the AT&T store.
90
MIN

NOTE: Some mobile devices will display items differently.
Connect your device to the Internet
Connect the yellow ethernet cable from the
“Ethernet” port on your MicroCell to your router.
Quick Setup
(If you don’t have a router, see User Guide page 9.)
Visit att.com/3GMicroCell-Activate
and follow the instructions on the screen.
You’ll need the following:
» Serial number (S/N)—it’s on the bottom of the
device and the box label.
» Your AT&T wireless phone number/user name or AT&T
Access ID, as well as your password. If you haven’t set up
an AT&T online wireless account, you’ll need to do so.
Power on your device
Activate your device online
Connect your MicroCell to a power outlet
with the AC power adapter.
The Power light on the front of the device will come on
immediately. Within a few minutes, other lights will flash
as a GPS signal is located and software is updated.
NOTE:
Hold on to this guide;
you’ll come back to
it after you activate
your device.
www
Take a break!
You will receive a text message and email once
activation is complete.
Visit att.com/3GMicroCell to learn more on how to
get the most out of your MicroCell.
Wait while your device connects
NOTE:
It can take up to 90
minutes to complete
activation. Your
device may update
and restart during
this time.
The GPS and 3G lights will start
flashing GREEN after connecting
power to your device. Solid GREEN
indicates activation is complete!
3G Status Confirmation
Confirm your success
Your device is configured and working
properly when:
» You receive a text message and an email confirmation.
» The 3G light on your MicroCell is solid and GREEN.
» Your cell phone shows “AT&T MicroCell” or “AT&T
M-Cell” instead of “AT&T” as the network provider
(as shown below).
NOTE:
You may need to
restart your cell
phone for “AT&T
MicroCell” or “AT&T
M-Cell” to appear.
14
25
3
AT&T AT&T MicroCell AT&T M-Cell
or
Power
Solid Green
Ethernet
Solid Green
GPS
Solid Green
Computer
3G
Solid Green
Proceed to Step 4 if you completed online activation at the AT&T store.
90
MIN

NOTE: Some mobile devices will display items differently.
Connect your device to the Internet
Connect the yellow ethernet cable from the
“Ethernet” port on your MicroCell to your router.
Quick Setup
(If you don’t have a router, see User Guide page 9.)
Visit att.com/3GMicroCell-Activate
and follow the instructions on the screen.
You’ll need the following:
» Serial number (S/N)—it’s on the bottom of the
device and the box label.
» Your AT&T wireless phone number/user name or AT&T
Access ID, as well as your password. If you haven’t set up
an AT&T online wireless account, you’ll need to do so.
Power on your device
Activate your device online
Connect your MicroCell to a power outlet
with the AC power adapter.
The Power light on the front of the device will come on
immediately. Within a few minutes, other lights will flash
as a GPS signal is located and software is updated.
NOTE:
Hold on to this guide;
you’ll come back to
it after you activate
your device.
www
Take a break!
You will receive a text message and email once
activation is complete.
Visit att.com/3GMicroCell to learn more on how to
get the most out of your MicroCell.
Wait while your device connects
NOTE:
It can take up to 90
minutes to complete
activation. Your
device may update
and restart during
this time.
The GPS and 3G lights will start
flashing GREEN after connecting
power to your device. Solid GREEN
indicates activation is complete!
3G Status Confirmation
Confirm your success
Your device is configured and working
properly when:
» You receive a text message and an email confirmation.
» The 3G light on your MicroCell is solid and GREEN.
» Your cell phone shows “AT&T MicroCell” or “AT&T
M-Cell” instead of “AT&T” as the network provider
(as shown below).
NOTE:
You may need to
restart your cell
phone for “AT&T
MicroCell” or “AT&T
M-Cell” to appear.
14
25
3
AT&T AT&T MicroCell AT&T M-Cell
or
Power
Solid Green
Ethernet
Solid Green
GPS
Solid Green
Computer
3G
Solid Green
Proceed to Step 4 if you completed online activation at the AT&T store.
90
MIN

NOTE: Some mobile devices will display items differently.
Connect your device to the Internet
Connect the yellow ethernet cable from the
“Ethernet” port on your MicroCell to your router.
Quick Setup
(If you don’t have a router, see User Guide page 9.)
Visit att.com/3GMicroCell-Activate
and follow the instructions on the screen.
You’ll need the following:
» Serial number (S/N)—it’s on the bottom of the
device and the box label.
» Your AT&T wireless phone number/user name or AT&T
Access ID, as well as your password. If you haven’t set up
an AT&T online wireless account, you’ll need to do so.
Power on your device
Activate your device online
Connect your MicroCell to a power outlet
with the AC power adapter.
The Power light on the front of the device will come on
immediately. Within a few minutes, other lights will flash
as a GPS signal is located and software is updated.
NOTE:
Hold on to this guide;
you’ll come back to
it after you activate
your device.
www
Take a break!
You will receive a text message and email once
activation is complete.
Visit att.com/3GMicroCell to learn more on how to
get the most out of your MicroCell.
Wait while your device connects
NOTE:
It can take up to 90
minutes to complete
activation. Your
device may update
and restart during
this time.
The GPS and 3G lights will start
flashing GREEN after connecting
power to your device. Solid GREEN
indicates activation is complete!
3G Status Confirmation
Confirm your success
Your device is configured and working
properly when:
» You receive a text message and an email confirmation.
» The 3G light on your MicroCell is solid and GREEN.
» Your cell phone shows “AT&T MicroCell” or “AT&T
M-Cell” instead of “AT&T” as the network provider
(as shown below).
NOTE:
You may need to
restart your cell
phone for “AT&T
MicroCell” or “AT&T
M-Cell” to appear.
14
25
3
AT&T AT&T MicroCell AT&T M-Cell
or
Power
Solid Green
Ethernet
Solid Green
GPS
Solid Green
Computer
3G
Solid Green
Proceed to Step 4 if you completed online activation at the AT&T store.
90
MIN

AT&T 3G MicroCell™
Q
u
ic
k
St
ar
t
Status Indicators (Front of the Device)
Computer
Ethernet
Power
Getting To Know Your Device
Package Contents
AT&T 3G MicroCell™ | AC power adapter | Yellow ethernet cable | Quick Start | User Guide
To view an activation tutorial, visit att.com/3GMicroCell under the “Help“ tab.
Power
Ethernet
GPS
Computer
3G
Before You Begin
Serial Number (S/N) Tip
Write down your MicroCell’s serial number; you’ll
need it for online activation and future reference.
It can be found on the bottom of the device or on
the box label.
Serial # (S/N)
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and
other countries. A listing of Cisco’s trademarks can be found at www.cisco.com/go/trademarks. Third-party
trademarks mentioned are the property of their respective owners. The use of the word partner does not imply
a partnership relationship between Cisco and any other company. AT&T, the AT&T logo, and AT&T 3G MicroCell
are trademarks of AT&T Knowledge Ventures. Product and service availability is subject to change without notice.
Portions © AT&T Intellectual Property. Portions © Cisco and/or its affiliates. All rights reserved.
February 2012 Part Number 4038348 Rev B
Having Trouble?
1. Have you waited at least 90 minutes?
2. Have you activated your MicroCell online and received the
Online Activation Complete email?
3. Does your MicroCell have a solid GPS light?
4. Is your Internet connection and home network up and
running and connected?
Need More Help?
Refer to the Troubleshooting section in the User Guide,
visit att.com/3GMicroCell-Help,or call AT&T Support at
1-800-331-0500.
• Plan your installation location – your device should be:
– Within three feet of a window to receive a GPS signal for 911 purposes.
– At least one foot away from other wireless broadcasting devices to avoid possible interference.
– Where you can connect your MicroCell to your Internet equipment.
• Plan on 10-15 minutes for equipment setup and online activation. Your device will then need up to
an additional 90 minutes for final device activation, which requires no effort on your part.
• You will need your AT&T wireless phone number/user name or AT&T Access ID, as well as your
password for online activation. If you haven’t set up an AT&T online wireless account, you can do
so while activating your MicroCell online.