AMG Systems AMG5424R User manual

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 1 of 8 AMG5424R Instruction Sheet D17406-
00
AMG5424
R
Instruction Manual
Dual System with 2x Independent Channels each of:
[Receive Unit with one Bi-directional Data Channel and one
Bi-directional Alarm for a Multimode Fibre Link]
The AMG5424R is a DUAL rackmount data receive unit which provides two independent channels,
each designed to transmit and receive 1 bi-directional alarm and transmit and receive 1 data signal
over one Multimode optical fibre.
The AMG5424R is designed to plug into an AMG2009 or AMG2015 subrack, which in turn fits into a
19" rack system.
The AMG5424R is designed to operate with two AMG5413single channel or one AMG5423 /
AMG5424R dual channel transmit units in a point to point configuration. The R suffix in the partno.
indicates a rackmount configuration.

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 2 of 8 AMG5424R Instruction Sheet D17406-
00
Contents
Introduction 3
Unit Functional Schematic.................................................................................................................. 3
Optical Connection ............................................................................................................................. 3
Connections 4
Optical Connections Multimode.......................................................................................................... 4
Power Connection .............................................................................................................................. 4
Data and Alarm Channel Connections ............................................................................................... 4
Front Panel Indicators 5
Power / Opto LED............................................................................................................................... 5
Low Speed Data LEDs ....................................................................................................................... 5
Alarm LEDs......................................................................................................................................... 5
Data and Alarm Channel Configuration 6
Data Channel Configuration ............................................................................................................... 6
Data Interface Connections ................................................................................................................ 7
Alarm Channel Configuration ............................................................................................................. 7
Alarm Interface Connections .............................................................................................................. 7
Physical Information 8
Dimensions ......................................................................................................................................... 8
Mounting Details ................................................................................................................................. 8
Removal / replacement from / to the Case......................................................................................... 8
Safety 8
Maintenance and Repair 8

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 3 of 8 AMG5424R Instruction Sheet D17406-
00
Introduction
Unit Functional Schematic
The AMG5424R provides two
independent, receive channels.
Each channel receives 1 data and 1 bi-
directional alarm signal from up to two
AMG5413transmit units.
It also transmits 1 data signal to each
AMG5413.
The schematic diagram shows one of the
two available channels of the AMG5424R
Optical Connection
The AMG5424R connections are illustrated in the following example which shows two AMG5413
single channel transmit units together with an AMG5424R configured as a dual channel point to point
system.

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 4 of 8 AMG5424R Instruction Sheet D17406-
00
Connections
Optical Connections Multimode
No. of Optical Connections ..................1 per channel
Optical Fibre ........................................Multimode 50/125 or 62.5/125**
Connector ............................................SC/PC
Minimum Optical Launch Power..........-10dBm
Transmit Wavelength...........................1550nm
Minimum Optical Sensitivity.................-30dBm
Receive Wavelength............................1310nm
Minimum Optical Dynamic Range .......20dB.
**Note: the transmission distance is limited by the bandwidth of the Multimode optical fibre. The optical
data rate is 155Mbits/s, which may restrict operation to a maximum fibre length of 7km, although in
most cases the units will operate successfully over longer fibre lengths. It is advisable however for
distances greater than 7km, to have the optical fibre tested.
Power Connection
Power supply .......................................From plug in connection on the AMG2009 or AMG2015 subrack
Power consumption .............................2.5 Watts max.
Data and Alarm Channel Connections
No. of Data Channels ..........................1 per channel.
No. of Alarm Channels.........................1 per channel.
Connectors ..........................................Removable 8-pin, 2.5mm, Screw Terminal
Connector Partno.................................Phoenix 1881383
Data Interfaces ....................................RS-232, RS-422 or R-S485. Selected by slide switch inside
enclosure. *See appropriate section on how to remove the case
for access to the data switches
RS-485 – Switch Position - Top
RS-422 – Switch Position - Middle
RS-232 – Switch Position - Bottom
Alarm Output........................................Solid-state Relay, maximum 150mA at 125Vac/dc, Ron < 6.5Ω

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 5 of 8 AMG5424R Instruction Sheet D17406-
00
Front Panel Indicators
Power / Opto LED
Power / Opto........................................ Green - Unit powered, Opto sync.
Red - Unit powered, no Opto sync.
Off - No power applied to unit
Low Speed Data LEDs
Data Present IN (RS485 or RS422) .... Green - logic zero (+V, -V) present on IN+, IN-
Red - logic one (-V,V+) present on IN+, IN-
Off - tri-state off or no connection on IN+, IN-
Data Present IN (RS232) .................... Green - logic zero (+V) present on input IN+
Red - logic transitions present on input IN+
Off - logic one (-V) present on input IN+
IN corresponds to the data signals being transmitted onto the optical fibre.
Data Present OUT (RS485 or RS422) Green - logic zero (+V,-V) present on OUT+, OUT-
Red - logic one (-V,+V) present on OUT+, OUT-
Off - tri-state off or no connection on OUT+, OUT-
Data Present OUT (RS232) ................ Green - logic zero (+V) present on OUT+
Red - logic transitions present on OUT+
Off - logic one (-V) present on OUT+
OUT corresponds to the data signals being received from the optical fibre.
Alarm LEDs
ALARM 1 IN......................................... Green - Alarm ON / Contacts closed.
Off - Alarm OFF / Contacts open.
ALARM 2 IN......................................... Green - Alarm ON / Contacts closed.
Off - Alarm OFF / Contacts open.
ALARM 1 OUT..................................... Green - Alarm ON / Contacts closed.
Off - Alarm OFF / Contacts open.
ALARM 2 OUT..................................... Green - Alarm ON / Contacts closed.
Off - Alarm OFF / Contacts open.

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 6 of 8 AMG5424R Instruction Sheet D17406-
00
Data and Alarm Channel Configuration
The AMG5424R sends and receives data to/from up to two AMG5413single channel or one
AMG5423 or AMG5423R rackmount equivalent dual channel transmit units. Each physical data
interface RS-485, RS-422 or RS-232 is individually selectable by the user with the corresponding slide
switch mounted on the main PCB inside the enclosure.
1 bi-directional alarm is also provided for each video channel, each of which can receive an on/off
signal from an AMG5413and are typically used to convey contact closure status. Each alarm output
uses a Solid-state relay, with a maximum load current of 150mA at 125Vac/dc and Ron < 6.5Ω.
Data Channel Configuration
Each low speed data channel provides an RS-232, RS-422 (full duplex, four wire) or RS-485 (half
duplex, two wire) interface defined by the corresponding mode switch inside the enclosure. Every data
channel as shipped from the factory is set up for RS-485 operation unless otherwise requested.
The data input for both the RS-485 and the RS-422 modes detects a tri-state input condition by
monitoring the differential voltage level across the input. A differential level below 600mV positive or
negative will be detected as a tri-state condition. A level above 600mV positive or negative will be
detected as a logic 1 or logic 0 respectively. It is important therefore to terminate the RS-485 bus or
the RS-422 input bus using 120Ω if a pre-bias is present on the RS-485 or RS-422 bus.
A large number of third party equipment manufacturers apply a pre-bias on their RS-485 bus. This pre-
bias is applied by pulling one arm of the RS-485 bus high (+5 volts) and the other arm low (0 volts)
using high value resistors within the third party equipment. In order to ensure that the AMG equipment
detects a tri-state condition, then these resistors should have a value above 5kΩ. If the third party
bias resistors are less the 750Ω the bus can be multiple terminated as required to ensure that a tri-
state level is detected.

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 7 of 8 AMG5424R Instruction Sheet D17406-
00
The system detects a tri-state input condition on the data channel bus when in RS-485 or RS-422
mode.
Data Interface Connections
Data Channels 1 and 2.
Connector
Pin No.
Data Channel
RS-485
[switch top]
RS-422
[switch middle]
RS-232
[switch bottom]
1
IN + (A)
IN
2
IN - (B)
3
GND
GND
GND
4
5
6
7
IN/OUT + (A)
OUT + (A)
8
IN/OUT - (B)
OUT - (B)
OUT
Note: (A) or (B) in brackets in the above table refers to RS-485 / RS-422 data specification.
Alarm Channel Configuration
The AMG5424R provides one bi-directional alarm output / contact closure input per channel.
The alarm input is typically connected to a contact closure switch. An ALARM IN+ input incorporates a
330R pull-up resistor to the internal +3V3 supply.
The alarm output can receive an on/off signal from an AMG5413and is typically used to convey
contact closure status. An alarm output uses a solid-state relay, with a maximum load current of
150mA at 125Vac/dc and Ron < 6.5Ω.
Alarm Interface Connections
Channels 1 & 2
Connector Pin
No.
Alarm Interface
Alarm IN
Alarm OUT
1
2
3
GND
4
ALARM IN +
5
ALARM OUT -
6
ALARM OUT +
7
8

AMG Systems Ltd. reserves the right to make changes to this
document without notice. The information herein is believed to
be accurate. No responsibility is assumed by AMG for its use.
Page 8 of 8 AMG5424R Instruction Sheet D17406-
00
Physical Information
Dimensions
Height...................................................3U Plig-in
Width....................................................7HP
Depth ...................................................170mm (excluding connectors)
Weight..................................................600grams
Mounting Details
The AMG unit is supplied with a clip-on mounting bracket which should be attached to a panel or wall
using 2 off 4.0mm screws, see diagram on page 1 for dimensions. The unit is clipped into the
mounting bracket, and is then held firmly in position.
Removal / replacement from / to the Case
Note: - The AMG unit PCB is static sensitive. Handle with proper care and use normal electrostatic
discharge (ESD) procedures. Use properly grounded protection (for example, wrist straps) when
handling the PCB out of the case.
To remove the PCB from the case for example to access a Low Speed Data mode switch, remove the
2 fixing screws on the rear panel and slide the PCB sufficiently out of the case to enable access to the
switch.
To replace the PCB into the case, slide the PCB gently into the case, if necessary aligning the board
with the appropriate slots.
Safety
AMG Optical Fibre Products use Class 1 laser systems in accordance with EN 60825-2:2000.
It is always advisable to follow good practice when working with optical fibre systems. This includes:
Do not stare with unprotected eyes or with any unapproved collimating device at fibre
ends or connector faces, or point them at other people.
Use only approved filtered or attenuating viewing aids
For other safety issues and advice on good practice associated with optical fibre systems, please see
EN 60825-2:2000 or your local safety officer.
Maintenance and Repair
There are no user serviceable parts within AMG products. See unit data sheet for full specification.
In case of problem or failure, please call your local support centre or contact: AMG Systems Ltd. at
3 The Omega Centre, Stratton Business Park, Biggleswade, Beds., SG18 8QB, UK.
Phone [phone]
Technical Support [phone]
Email [e-mail]