Atdec AV Cart 75 User manual

AD-TVC-75 Page 1 of 4
Installation Guide
AD-TVC-75
AV Cart 75
COMPONENT CHECKLIST
A
Base (x1)
E
Shelf (x1)
F
Shelf Lip
(x1)
G
LHS VESA
Bracket (x1)
H
RHS VESA
Bracket (x1)
K
Shelf Connection
(x2)
L
Grommet
(x2)
M
Hook and
Loop (x3)
I
Shelf Clamp (x1)
J
Castor (x4)
A1
M8x25
Screw (x4)
B1
M6x25
Screw (x4)
C1
M5x25
Screw (x4)
E1
ø16xø6.2
Washer (x4)
F1
ø15x10mm
Spacer (x4)
A2
M8x20
Screw (x2)
B2
M8x20
Cap Screw (x2)
C2
M8x72
Cap Screw (x4)
D2
M5 Allen
Key (x1)
E2
M6 Allen
Key (x1)
C
Mounting Plate (x1)
B
Column (x1)
D
Mounting Brace (x1)
D1
M4x12
Screw (x4)
F2
ø19x13mm
Spacer (x4)
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! The manufacturer accepts no responsibility for incorrect installation.
! Failure to mount this product correctly may cause serious injury/death during or following installation.
! This product should only be installed by professional installers of good mechanical aptitude, who fully understand these
instructions and the consequences of incorrect installation.
! Do not over tighten screws.
! Two person installation is recommended.
! Product not suitable for use outdoors.
! After installation is complete check to verify that AV Cart is secure and safe for use.
! Curved monitors, deep devices (such as all-in-one PCs), VESA mounted accessories (such as mini PC brackets and mounts), and offset VESA
locations exert additional leverage that can exceed the capacity of the mount even though the monitor weight may be within the stated range.
Please contact Atdec if you would like further information.
! WARNING! Death or serious injury may occur when children climb on audio and/or video equipment furniture. A remote control
or toys placed on the cart may encourage a child to climb on the cart and as a result the cart may tip over on to the child.
REQUIRED TOOLS
• Phillips Head Screwdriver
CAPACITY
DISPLAY
0 - 75kg (0 - 165lb)
50” - 80”
SHELF
0 - 11kg (0 - 24lb)

AD-TVC-75 Page 2 of 4
1. Install the castors
1.1 1.2
WARNING!
! CART CAN TIP OVER RESULTING IN RISK OF INJURY!
! DO NOT ALLOW CHILDREN UNDER 16 TO PLAY WITH OR MOVE CART
! MOVE CART SLOWLY
DO NOT PULLNEVER APPLY FORCE
AT TOP
APPLY FORCE ON
NARROW SIDES
PUSH NEAR MIDDLE
DO NOT APPLY
MOVING FORCE ON
FRONT OR BACK
ONLY ADULTS SHOULD
MOVE THIS CART
LOCK
BRAKES WHEN
STATIONARY
UNLOCK
BRAKES BEFORE
MOVING
DO NOT PULL
NEVER APPLY FORCE AT
TOP
APPLY FORCE ON
NARROW SIDES
PUSH NEAR MIDDLE
DO NOT APPLY MOVING
FORCE ON FRONT OR
BACK
ONLY ADULTS SHOULD
MOVE THIS CART
LOCK
BRAKES WHEN
STATIONARY
UNLOCK
BRAKES BEFORE
MOVING
2. Attach column to the base
D2
A2
Base bottom
B2
E2
2.1 2.2 2.3
Note: Make sure
cable management
windows are facing
the rear of base.
Caution: Ensure
screws are secured firmly.
3. Set column height
Right
upper
column
Right
lower
column
Spring
button
Safety
screw
Left
lower
column
Left
upper
column
E2
Safety
screw
Spring
Button
E2
3.1 Unscrew safety screw on right
lower column using 6mm Allen key.
Put safety screw aside.
3.2 Use thumb or finger to depress
the spring button located on the right
lower column (Near cable window). At
the same time use other hand to twist
then pull right upper column upward
until your desired height. Twist motion
is to ensure spring button doesn’t
engage unintentionally. Twist upper
column back toward the plunger holes
and engage spring button into the
plunger hole. You may need another
person to help. (Fig-1)
3.3 Ensure spring button pops out and
secure safety screw. (Fig-2)
3.4 Repeat steps 1, 2 and 3 on left
column.
Fig-1 Fig-2

AD-TVC-75 Page 3 of 4
4. Install shelf
6. Attach VESA brackets to display
G H
M8x25mm A1
M5x25mm C1
M6x25mm B1 M4x12mm D1
F1 E1
(A1,B1,C1)+E1+F1/D1+E1
Note: Use spacers
where necessary to
ensure brackets are
not loose, and screws
are not forced too
deep into the display.
6.1
6.3
6.2
Fastener configuration examples
Remove, retain for step 7.2
5. Attach mounting plate
E2
F2
C2
C
D
K
I
E
F
4.1
4.4
4.6
4.2
4.3
4.5
Note: To adjust shelf height
loosen 4x screws under shelf,
slide shelf up or down into
position then tighten screws
to set.

AD-TVC-75 Page 4 of 4
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specifications without notice. ©20210915
9. Adjust display height
9.1 Two people are required to change display height.
Display must be removed prior to adjusting height.
9.2 Person “A” holds the top
section of the telescopic column.
Person “B” unscrews 2x safety
screws from left and right poles by
using 6mm Allen key. Put screws
aside. Carefully depress both
spring buttons on poles by using
thumbs, so that person “A” can
move top of column down or up to
desired height.
9.3 When height is determined,
let spring buttons set into plunger
holes. Ensure both spring buttons
have popped out. Secure 2x safety
screws.
E2
Spring button
Safety screw
8. Cable routing options
8.1 Cables may be routed down the
inside or outside of column
M
L
Note: Grommets must be
inserted into tube prior to
inserting cables
Maintenance
• Tighten fasteners and check the cart is secure and safe to use
at regular intervals (at least every three months.)
• Please contact your distributor if you have any questions.
Caution: These parts must
be attached to prevent accidental
dislodgement of screen.
Note: Centre display after hooking it
over mounting bracket
7.2
7. Mount display
7.1