Atec 6275 KWIKSTART User manual

Model 6275 KWIKSTART
(12 Volt DC Portable Power Source)
USER’S MANUAL
This unit has a sealed lead acid battery that should be kept at full charge. Recharge when first
received, immediately after each use, and every three months if not used (this charger
contains a smart circuit which allows it to be left on charge continuously without damage).
Failure to do this may cause the battery life to be reduced greatly.
SPECIFICATIONS
Voltage: 12 VDC
Peak-Amp power: 12V-3400A
12V output and charging protected socket
Battery type: 2-12V/22AH 360CCA (12V 720 CCA)
Internal Charger: 12V / 1000mA
Booster cables: 2AWG with insulated clamps
Automatic charging circuit
Charging and Charged LED indicators
Multiple LED power level indicators
IMPORTANT SAFETY INSTRUCTIONS
1. SAVE THESE INSTRUCTIONS – This manual contains
important safety and operating instructions.
1
ity of battery. Review
3. P
near a lead-acid battery.
d.ith
enters eyes, immediately flood eyes with
immediately. r
f. of dropping a metal tool onto
ctrical
g. ttery. A
gh
h. re
nces. These batteries may
i. ttery. the same piece
4. IM
a. attachment not recommended or sold by the
necting.
em immediately.
sed under any weather condition; rain,
f.
g. service it.
ry recycler in your area.
. Do not disassemble the KWIKSTART. Have it checked by a
state for
sult. When not in use, leave the
KWIKSTART’s internal charger connected to AC power or recharge
every three (3) months.
Contains sealed, non-spillable lead acid
battery. Must be disposed of properly.
2. WARNING – RISK OF EXPLOSIVE GASES.
a. Working in the vicinity of a lead acid battery is dangerous.
Batteries generate explosive gases during normal battery
operation. For this reason, it is of utmost importance that when
using the KWIKSTART, you read this manual and follow the
instructions exactly.
b. To reduce risk of battery explosion, follow these instructions and
those published by battery manufacturer and manufacturer of any
equipment you intend to use in vicin
cautionary marking on these products and on engine.
ERSONAL PRECAUTIONS
a. Someone should be within range of your voice or close enough to
come to your aid when you work
b. Have plenty of fresh water and soap nearby in case battery acid
contacts skin, clothing, or eyes.
c. Wear complete eye protection, and clothing protection. Avoid
touching eyes while working near battery.
If battery acid contacts skin or clothing, wash immediately w
soap and water. If acid
running cold water for at least 10 minutes and get medical
attention
e. NEVER smoke or allow a spark or flame in vicinity of battery o
engine.
Be extra cautious to reduce risk
battery. It might spark or short circuit battery or other ele
part that may cause explosion.
Remove personal metal items such as rings, bracelets,
necklaces, and watches when working with a lead-acid ba
lead-acid battery can produce a short circuit current high enou
to weld a ring or the like to metal, causing a severe burn.
Use this KWIKSTART for charging or boosting a LEAD-ACID
battery only. Do not use for charging dry-cell batteries that a
commonly used with home applia
burst and cause injury to persons and damage to property.
NEVER charge a frozen ba
j. NEVER allow clamps to touch together or contact
of metal to prevent arcing.
PORTANT SAFETY INSTRUCTIONS
Use of an
manufacturer may result in a risk of fire, electric shock, or injury to
persons.
b. When using the internal charger or DC power extension cord, pull
on the plug and NEVER ON THE WIRE when discon
c. Do not recharge the KWIKSTART with a damaged charger or DC
power extension cord. Replace th
d. The KWIKSTART may be u
snow, hot, or cold temperatures.
e. Do not submerge in water.
Do not operate with flammables such as gasoline etc…
If the KWIKSTART receives a sharp blow or is otherwise
damaged, in any way, have it checked by a qualified
person. If the KWIKSTART is leaking battery acid do not ship
Take it to the closest batte
hqualified service person.
The KWIKSTART should never be left in a total discharged
any period of time. Damage to the battery could be permanent with
poor performance as a re
Consumer: Retain these instructions for future use. Read all instructions carefully before using this KWIKSTART
(Portable Power Source).

2
NOTE: first
gh
the KWIKSTART
could be damaged due to overcharging.
1.
gh a
g
The
d. he red LED goes off and
e. y
charger remain connected to an AC power source whenever the
2.
he test
OVERCHARGE! This is not an automatic method of charging the
KWIKSTART. Overcharging will damage your KWIKSTART.
CTIONS
t it will not start the vehicle without assistance. However, the
WIKSTART can also be used to restore some charge to the vehicle
. Plug the power extension cord from the KWIKSTART into the
OTE: Some vehicle’s ignition keys must be turned to accessory to
OTE: A defective battery may refuse to accept a charge from the
MERGENCY JUMP STARTER
0°F when using
fore making cable connections.
3.
he vehicle frame (ground).
moving belts or fan.
8. Sta
NOTE: ry cool for 3 minutes before
START may occur.
the vehicle frame.
2. Return jumper cables to their stored position.
. However, if
e power extension cord is plugged from the KWIKSTART to the cigar
s OBD2 connector to save all memory functions. The
MS6209 memory saver may be purchased separately for these
applications.
FEATURES
1. Provides plenty of power for starting vehicles. More than enough to
start most vehicles. May also be used in DEEP CYCLE
applications.
2. The KWIKSTART will power most 12 VDC accessories equipped
with a male cigar lighter plug. The DC outlet has automatic overload
protection.
3. Test switch and Multiple LED power level indicators. State of the art
charging circuit.
4. ON/OFF switch. When in the OFF position, no voltage will be
present at the clamps, reducing the chance of arcing.
INFORMATION TO USER
Changes or modifications by the user, that are not expressly approved
by the party responsible for radio frequency emmission levels from the
KWIKSTART, could cause an undesirable amount of radio frequency
energy to be emitted. Such action could void the user's authority to use
the KWIKSTART.
SAFETY FEATURES
1. Selector switch prevents accidental sparking of clamps.
2. Cable bracket hold the cables for clean storage. (No unsightly
dangling wires).
3. The KWIKSTART contains the latest technology with its 2 -12 volt
sealed non-spillable batteries. The KWIKSTART may be stored in
any position.
RECHARGING PROCEDURES
When new, your KWIKSTART should be charged for a minimum of 30
hours, unless the green High power level LED lights when the test
button is pressed. (See Figure 2)
Figure 2.
ON/OFF switch, test button, power level LED’s, internal charger plug
There are two ways to recharge the KWIKSTART. The
method is automatic charging with the internal charger
(preferred). The second is through the DC power jack throu
the DC power extension cord. The second method is not
automatic and requires watching because
USING THE INTERNAL CHARGER: The KWIKSTART is
automatically charged using the internal charger. A two pin male
plug on the KWIKSTART’s control panel is connected throu
smart circuit board to the KWIKSTART making rechargin
automatic. Recharging takes approximately 24 hours.
Overcharging is not a problem when using the internal charger.
KWIKSTART’s internal charger can be left connected to an AC
power source indefinitely.
a. Turn the ON/OFF switch to OFF.
b. Connect an extension cord to the KWIKSTART’s male plug.
Plug the extension cord into a coc. rrectly wired AC receptacle (the
red CHARGING LED will light).
The battery will be fully charged when t
the green CHARGED LED comes on.
If you are not going to need the KWIKSTART right away you ma
leave the KWIKSTART’s internal charger connected to the AC
power source. We recommend that the KWIKSTART’s internal
KWIKSTART is not in use.
USING THE DC POWER EXTENSION CORD. Plug one end of the
power extension cord into the KWIKSTART power receptacle and
the other end into a vehicle’s lighter outlet (vehicle’s engine should
be running first). Turn the ON/OFF switch to ON. Push t
button once every hour to check the power level. When the High
power level LED lights the battery is charged. DO NOT
OPERATING INSTRU
USED AS A BATTERY CHARGER
The KWIKSTART is intended, primarily, to be used to start or restart a
vehicle when the battery in the vehicle has become run down to the
point tha
K
battery.
1vehicle’s cigar lighter outlet for 30 minutes.
N
activate the cigar light socket.
2. Remove the power extension cord and start the car.
NKWIKSTART.
USED AS AN E
NOTE: For optimum performance, do not store below 5
as a jump starter.
1. Turn ignition off be
2. Use in a well ventilated area.
SHIELD EYES.
4. Clamp the positive (red +) clamp to the positive terminal on the
weak battery (for negative ground system).
5. Clamp the negative (black –) clamp to t
Make sure the cables are not in the path of
6. Switch the ON/OFF switch to the ON.
7. Stay clear of batteries while jump starting.
rt the vehicle (turn on the vehicle ignition).
If the vehicle does not start within 6 seconds, let the
KWIKSTART internal batte
attempting to start the vehicle again or damage to the
KWIK
9. When the vehicle is started, turn the selector switch to the OFF
position.
10. Disconnect the negative (-) battery clamp from
11. Disconnect the positive (+) clamp.
1
13. Recharge at earliest convenience.
USED AS AN ALTERNATIVE POWER SUPPLY FOR
VEHICLES
The KWIKSTART is an essential tool for all who replace automobile
batteries. Most vehicles have some type of electronic component with
memory, such as alarm systems, computers, radios, phones, etc…
and when the vehicle’s battery is replaced, memory is lost
th
lighter outlet on the vehicle, the memories can be saved.
NOTE: Some vehicles may require the KWIKSTART to be connected
to the vehicle’

MULTI PURPOSE POWER SUPPLY
The KWIKSTART is also a portable power supply for all 12 VDC
accessories equipped with a male cigar lighter plug. The DC outlet
has automatic overload protection.
For maximum battery life do not discharge below 11V.
When the KWIKSTART is used with an inverter, it can operate
appliances normally powered by 120 VAC.
Recommended inverter for the KWIKSTART is 300 watts maximum.
For more information contact your nearest KWIKSTART dealer.
The most important item to insure
a long life from your KWIKSTART
is to keep the battery fully charged.
Charge after every use.
Charge every 3 months
!!! IMPORTANT !!!
BATTERY REMOVAL AND DISPOSAL
Contains sealed, non-spillable lead acid
battery. Must be disposed of properly.
3
The battery inside this KWIKSTART is a sealed lead-acid battery.
By LAW, it is required to be removed and recycled or disposed of
properly. While there are regulations that must be followed throughout
the country, your local governments may have additional regulations to
be followed in your area.
When the battery in this product is in need of replacement, remove it
according to the instructions provided below and take it to your local
recycling center for proper recycling or disposal. If you don’t have a
local recycling center that handles sealed lead-acid batteries, contact
your local environmental agency for instructions.
BATTERY REMOVAL INSTRUCTIONS
Begin by making sure that both booster clamps are securely stowed in
their storage holders on each side of the KWIKSTART.
1. Lay the KWIKSTART down on its front. On the back of the unit,
locate the 10 screws that hold the enclosure together.
2. Remove the 10 screws, and then lift off the back half of the
enclosure.
3. On the top of the batteries are two terminals, each with wires
connected to them. Disconnect these wires from the battery by
removing the bolts that hold them to the battery terminals. TO
PREVENT ACCIDENTAL ARCING, be careful no to touch both
battery terminals with the tools being used to remove the bolts.
4. Lift the battery out of the front half of the enclosure.
5. To install a new battery, reverse the above procedure.
NOTE: Remember that the red wires connect to the positive (+) battery
terminal and the black wires connect to the negative (-) battery
terminal.
LIMITED WARRANTY
Associated Equipment Corporation provides a conditional, limited
warranty to the original user or consumer purchaser for the
KWIKSTART, warranting it to be free from defects in material and
workmanship for a period of one year from the date of sale to the
original user or consumer purchaser. If your KWIKSTART
malfunctions or fails within the first 30 days of the warranty period
because of a defect in material or workmanship, we may replace it. If
your KWIKSTART malfunctions or fails within the 12-month warranty
period because of a defect in material or workmanship, we will repair it
without charge.
This warranty does not apply to the battery. All battery
replacements will be at the sole discretion of Associated
Equipment Corporation, and subject to visual and internal
inspection. Any battery replacement will be on a prorated,
escalating cost basis to the purchaser, prorated monthly for a 12
month period from the date of purchase (with proof of purchase)
or date of manufacturer (without proof of purchase), and
increasing in 1/12th increments monthly up to the retail battery
price set by the Associated Equipment Corporation. Batteries
returned with melted terminals, or subjected to overcharging or
misuse, will not be covered under warranty.
EXCEPT FOR THIS LIMITED WARRANTY, ASSOCIATED
EQUIPMENT CORPORATION HAS NOT MADE AND SPECIFICALLY
DISCLAIMS ANY WARRANTY OR REPRESENTATION OF ANY
KIND, EXPRESS OR IMPLIED, DIRECT OR INDIRECT, INCLUDING
BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF
MERCHANTABILITY, AND ANY IMPLIED WARRANTY OF FITNESS
FOR A PARTICULAR PURPOSE. THIS LIMITED, CONDITIONAL
WARRANTY PROVIDES THE EXCLUSIVE REMEDY FOR ANY
CLAIM OR DAMAGE EXCEPT AS OTHERWISE REQUIRED BY
LAW.
This warranty excludes and does not cover defects or failures of your
KWIKSTART due to any cause other than defects in material or
workmanship, including without limitation any malfunctions or failures
caused by repairs made by an unauthorized person, mishandling,
modifications, normal wear, unreasonable use or damage.
IN NO EVENT SHALL ASSOCIATED EQUIPMENT CORPORATION
BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES.
Some states do not allow the exclusion or limitation of incidental or
consequential damages so the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights and you may
also have other rights which vary from state to state.
Any claim relating to the KWIKSTART must be brought within one year
and must be brought in Missouri. Missouri law shall govern all claims.
If any portion of this warranty or limitation of rights and remedies is
found to be unenforceable, then the remainder of this document shall
remain in full force and effect.
To Obtain Warranty & Non-Warranty Service
DO NOT RETURN THE KWIKSTART TO THE STORE
WHERE PURCHASED.
To obtain service:
1. Return your KWIKSTART prepaid (all postage, transportation
and freight charges to and from Associated Equipment
Corporation are the responsibility of the customer) in its original
box (including the internal battery), with the original sales receipt
(or other proof of purchase date). Also include your name,
mailing address, name of store where the product was
purchased and the daytime phone number you can be reached
to:
ASSOCIATED EQUIPMENT CORPORATION
ATTN: REPAIR DEPT.
5043 FARLIN AVENUE
ST. LOUIS, MO 63115
2. Associated Equipment Corporation will repair your KWIKSTART.
If the battery needs to be replaced, a technical service
representative will call you to advise of the prorated cost of the
replacement battery. Associated Equipment Corporation will
repair and return your KWIKSTART freight prepaid if the product
is covered under warranty.
If you have questions the Technical Service Department can be
reached Monday through Friday 7am to 3:30pm Central time.
Tel. [phone]
Email: [email protected]

4
NOTES:
027-0861 20091221