Atexco X User manual

Model X High Speed Sublimation printer
1
Model X
High Speed Sublimation printer
User manual
Ver 1.0
Hangzhou Honghua Digital Technology Stock Co., Ltd.
Address: 3911 Binsheng Road, Binjiang District, Hangzhou
Postal Code (PC): 310052
TEL：[phone]
FAX：[phone]
E-Mail：honghu[email protected]
Website：www.atexco.cn

Model X High Speed Sublimation printer
2
Preface
Thank you very much for purchasing the Model X series machine.
l In order to ensure the correct and safe use of the product based on a
comprehensive understanding of the performance of this product, please read
this manual and keep it in a safe place.
l It is forbidden to illegally copy this manual in whole or in part, otherwise the
company will pursue its legal responsibility according to the law.
l The contents of this manual and the parameters of this product are subject to
change without notice.
l We tried our best to edit this operation manual and test this product. If you find
any misprints or errors, please let us know and let us make changes. We will
be very grateful.

Model X High Speed Sublimation printer
3
Ensure safety and proper use
• To ensure the safe and proper use of the printer, please read this manual carefully before use.
• After reading the manual, keep it in a safe place and refer to it when necessary.
• Do not allow children to touch the printer to avoid injury or damage to the machine.
• The following instructions are very important for safe operation and must be strictly observed.
Manual usage agreement
Ensuring safe and proper use of the printer in order to prevent personal injury and property damage.
Knowledge about safety prevention is classified in the manual as 3 described categories, and a
thorough understanding of the differences between these categories is needed before reading the
manual.
DANGER If this type of prevention information is ignored, it will most likely cause serious harm to the operator.
WA RN I NG If this type of prevention information is ignored, it can result in serious operator injury.
CAUTION If this type of prevention information is ignored, it may result in operator injury or printer damage.
Safety symbol explanation
This symbol indicates: requires attention to danger.
This symbol indicates: prohibited from performing the operation.
This symbol indicates: an action must be performed.

Model X High Speed Sublimation printer
4
Safety guidance
Please read the following instructions before using your Model X High Speed Sublimation printer and
follow the warnings and instructions marked on the printer:
Printer installation considerations
WAR N I N G
Do not install the printer near solvents such as alcohol or thinner.
 If solvents come into contact with internal electronic components, it may cause fire or a short
circuit.
Do not place the following items on the printer.
 These items may come into contact with internal electronic components and may cause fire
and electrical shorts.
• Metal objects like necklaces.
• Objects such as glasses, vases, houseplants, including water and other liquids.
CAUTION
Do not place the printer in an insecure location, such as on a slope or where it can easily
vibrate or shake.
 Such a placement will cause the printer to tip over and be damaged.
Do not place heavy objects on the printer.
 Heavy objects may tip over and damage the machine.
If the printer is placed on a smooth surface, be sure to use the wheel brake to avoid moving
when using the printer.
 If the printer is not placed properly, the printer could trip over and be damaged.
Avoid using the printer in the following places.
 Using the printer in these locations may cause fire and short circuits.

Model X High Speed Sublimation printer
5
§ Excessively moist and dry places
§ Direct sunlight rooms
§ Hot places
§ Near an open flame or humid places
 Using the printer in the following places may cause the machine to malfunction or fail
• Producing a strong magnetic field near the device.
 The printer is suitable for use at temperatures between 25 ° C and 30 ° C and a humidity of
55% - 75% RH.
Ensure that there is enough room around the printer
 In order to ensure smooth operation, sufficient operating space should be reserved around the
front and rear of the printer.
Power supply safety precautions
WAR N I N G
Do not damage the power cord or attempt to repair it, and do not place heavy objects on the
power cord or bend it excessively.
 Failure to do so may result in electric leakage due to damage, resulting in fire or short circuit.
 Do not use a wet hand to plug in the power supply, which may cause a short circuit.
Avoid connecting many devices to the same power outlet.
 Failure to do so may result in fire or short circuit.
Do not bundle or wrap the power cord.
 Failure to do so may result in fire or short circuit.

Model X High Speed Sublimation printer
6
Make sure the power cord is securely plugged into a power outlet.
 Doing so may cause a fire or short circuit.
Do not use a power cord that is different from the one provided by the printer.
 Doing so may cause a fire or short circuit.
Pay attention to the following points when connecting the grounding.
 Allowed ground wire
• Power supply ground terminal
• Intact pile ground
 Ground wire that is not allowed to be connected
• Water pipe
• Gas pipe
• Telephone line and lightning protection wire
CAUTION
Use the appropriate supply voltage as described.
 Failure to use the specified power supply voltage may result in fire or short circuit.
When disconnecting the power cord, be sure to pull the plug, not the cord itself.
Do not use an additional power cord in general.
 If using an additional power cord, remember that the total amperage of the device
plugged into the additional power cord does not exceed the rated amperage of the
power source. Also, remember that the total amperage of all equipment plugged into
the wall does not exceed the rated amperage of the wall outlet.
Make sure the power plug can be easily removed at any time, ensure that no objects are
placed around it.
Ensure good grounding

Model X High Speed Sublimation printer
7
Avoid using the socket with the copier or air conditioning system, which are regularly
switched between on and off, in the same loop.
Avoid using sockets controlled by wall switches or automatic timers.
Keep your computer system away from potential sources of electromagnetic interference.
 For example: a speaker or a wireless phone.
Do not use damaged or worn power cords.
Operational safety precautions
WAR N I N G
Do not attempt to disassemble and repair the printer yourself.
If the printer produces abnormal noise, smoke, temperature rise, strange smell or
other abnormal function, immediately turn off the power, unplug the power cord and
contact the manufacturer where you purchased the printer.
Do not use flammable objects or similar products around the printer.
Before moving the printer, be sure to turn off the power and unplug the power cord.
Always use the power switch to turn off the printer. However, when the button is
pressed, the power will be cut off. Do not unplug the printer or the data cable until the
power is turned off.
Make sure the printhead is in the initial position and secure it before transporting the printer.
Do not touch any metal parts and printheads while the printer is operating.
A print failure may occur.
 Easily generated static electricity can cause damage.

Model X High Speed Sublimation printer
8
CAUTION
Take care to prevent internal electrical components from being in contact with metal objects
or liquids, as this may result in fire or electric shock.
Do not put your hand on the printer while printing.
Do not move the print head by hand as it may damage the printer.
Make sure the power cord is connected properly.
Facing some of these circumstances, after disconnecting the power source, please contact
experienced maintenance personnel to check the printer:
 If the power cord or plug is damaged;
 If liquid spills into the printer;
 If the printer falls or the case is broken;
 If the printer does not operate properly or there is a significant change in performance;
Maintenance and inspection
WAR N I N G
Be sure to turn off the power and do not perform any cleaning work until the power plug is
removed from the power outlet.
 Failure to do so may result in damage to the machine, fire hazard, and electric shock.
Clean the printer with a cloth that has been wetted with the cleaning solution. Do not use a
volatile solvent such as alcohol or benzene to clean the printer.

Model X High Speed Sublimation printer
9
Do not use any lubricant on the parts of the machine.
CAUTION
At least once a year, remove the power plug from the power outlet, move it and clean up the
surrounding area.
 Accumulated dust can cause a fire hazard.
When cleaning or inspecting the inside of the printer inside, make sure that metal objects,
such as necklaces or bracelets, do not touch any internal components.
 This type of action can result in injury or electric shock.
Consumables usage precautions
WAR N I N G
Be careful not to let ink splash into your eyes or mouth.
 This can cause difficulty breathing or damage your eyes.
 If ink gets into your eyes, rinse immediately and consult a doctor.
If you accidentally consume ink, do not try to induce vomiting, consult a doctor immediately.
The ink flowing into the printer can cause damage to the machine and affect the surface
coating of the printer.
CAUTION
For your safety, store printheads and ink out of the reach of children.
 If the ink is licked or ingested, consult a doctor immediately.

Model X High Speed Sublimation printer
10
Do not use any ink other than the one specified, as it may not only disturb the print quality
but also cause malfunction.
Do not use expired ink as this may cause a malfunction.
Dispose of waste ink in accordance with relevant regulations.
Be careful not to let ink get into your skin or clothing. If the ink gets to your skin, rinse it off
immediately with soap and water.
Check the waste ink bottle regularly to avoid spillage.
The ink should be stored in a dark and cool place. Do not expose the ink to high temperatures
or direct sunlight.