Atid AT911N series User manual

Guide for Customer
AT911N

ATID Co., Ltd
ATID is a registered trademark of ATID Co., Ltd.
AT911N is a registered trademark of ATID Co., Ltd. and of its wholly owned subsidiaries.
2
ATID Co., Ltd.
#1205, Byuksan/GyungIn Digital Valley II, #481-10,
Gasan-Dong, Gumchon-Gu, Seoul, Korea
Tel: [phone]
Fax: [phone]
www.atid1.com
Disclaimer
Copyright ⓒ2006 ATID Co., Ltd. An Unpublished Work – All right reserved.
No part of the contents of this documentation or the procedures described there in may be reproduced or
transmitted in any form or by any means without prior written permission of ATID Co., Ltd.. or its wholly owned subsidiaries ("ATID ").
Owners of ATID products are hereby granted a non-exclusive, revocable license to reproduce and transmit this documentation for the purchaser's own internal business
purposes.
Purchaser shall not remove or alter any proprietary notices, including copyright notices, contained in this documentation and shall ensure that all notices appear on any
reproductions of the documentation.
Should future revisions of this manual be published, you can acquire printed versions by contacting ATID Customer Administration. Electronic versions may either be
downloadable from the ATID web site (www.atid1.com) or provided on appropriate media.
If you visit our web site and would like to make comments or suggestions about this or other ATID publications, please let us know via the “Contact ATID ” page.

3
Contents
Page Contents
5 Before using manual for AT911N
Chapter 1. Caution when using AT911N
6 1. How to use battery correctly
6 2. Caution when using AT911N
Chapter 2. Product composition
7 1. Product composition
8 2. Name of each part
9 3. Function of each part
Chapter 3. Basic function
10 1. Attaching and Detaching the battery
12 2. Charging battery
12 3. Low power mode (Sleep mode)
14 4. Hard reset
15 5. Attaching Micro SD card
16 6. Attaching SIM card
17 7. Set screen brightness
17 8. Volume setting
18 9. Using keypad
18 10. Keypad button execution

4
Page Contents
Chapter 4. Optional module
20
21
23
24
25
26
27
28
28
29
1. Using 1D or 2D barcodescanner
2. Barcode emulator setting
3. Barcode scanning
4. WIFI connectionandtermination
5. Bluetooth connection andtermination
6. GPS demo program execution
7. Use of camera
8. NFC execution
9. NFC ON/OFF setting
10. UHF 900MHz RFID program
Chapter 5. Appendix
30 1. Product specication

5
■
◆
●
Before using manual for AT911N
User guide inclusive of text, images, logos, product names is either the property of, or used with permission by ATID CO.LTD. The information may not be distributed,
modied, displayed, reproduced (in whole or in part) without the prior written permission of ATID CO.LTD.
There are some dierences between user guide and actual function of device.
User guide can be adjusted by ATID CO.LTD without consent of user discretionally.
User guide is written for users who want to use and maintain the AT911N. Please read and understand these instruction prior to operating this unit.
Safety information
Your safety is extremely important. Read and follow all warnings and cautions in this document before you handle and operate ATID equipment. If you do not follow
the safety warnings and cautions, you might be seriously injured, and the equipment and data also might be damaged.
WARNIING
A warning requires you must pay attention to the operating procedure practice, condition, and statement strictly, or might be injured seriously.
CAUTION
A caution alerts you that you must be observe strictly when you operating procedure, practicing, conguring, for preventing from damage and destruction of
equipment, and loss of data.
NOTICE
A notice provide you the information which you must needs while you using AT911N.

6Chapter 1. Caution when using AT911N
•
Caution when using AT911N
Please aware of the manual contents in advance before you handle and operate your AT911N and other ATID Products.
How to use the battery correctly
In case that you dropped the main body or battery in water, please do not put into the stove or heater for drying. Just keep it in natural drying or contact purchase
place.
Please note that the battery terminal doesn’t have to be contacted to metallic object.
If you do not use the battery for a long time, please keep it at room temperature after charging.
Operating time of battery can be shorter than usual in accordance with loss of battery and use time. In this case, please contact us.
You have to use provided adaptor when charging the device.
Turn o the device properly then detach or replace the battery.
Caution when using AT911N
•
•
•
•
•
•
•
•
•
User careless or products repair would damage the stored data. Manufacturer is not responsible for this damage, so please do back-up the important data
separately.
If you have a problem on product, do not try to repair or disassemble it by yourself, please contact our customer service center.
Do not use your product at the specic places such as hospital, plane and so on where electromagnetic wave or the risk may occur.
Please note that using the device in environment of high temperature and humidity for long hours can make a malfunction of device.
•
•
In case of that noise, smoke and odor occur at the device while using product, please disconnect the charger with device and o the power immediately, then
please contact our customer service center.
If you have any other questions on use of device, please contact our customer service center.

7Chapter 2. Product composition
Product Composition
Product composition
Open the packing box and conrm the items as below.
*Please contact our customer service in defect of product composition and need to be changed.
5. Protect lm
3. Standard battery
6. Hand strap
2. Power Adapter and AC cable
1. AT911N main body
4. USB sync cable
AT911N is based upon Android 4.2. As the state of the art product, it is equipped with barcode scanner, RFID Tag reader, MODEM, Camera and so on and it can be
applied to Industry, Enterprise, Logistics and so on, can be used extensively in many elds due to this kind of various functions

8
Name of each part
Camera (Option)
Camera ash
(option)
1D/2D Scanner
(option)
Reset button
Touch Screen
Keypad
Microphone
Speaker Charge LED
WLAN LED/3G LED
Side key Side key
UHF
Gun handle
Sync cable connector/
DC Power Port
Internal NFC
(option)
Chapter 2. Product composition
Power key Earphone jack
Scan key

9
Function of each part
Chapter 2. Product composition
NAME FUNCTION
1D/2D Scanner (option) Please be careful not to get the damage or the foreign substances at the Window emitted the laser beam
Warning Do not look at the laser beam directly.
UHF Connecting port It is connector to equip the UHF 900MHz tag reader module.
Internal NFC (option) It is where Internal NFC is placed.
Reset button It is used for hard reset.
Microphone It is used for telephone conversation.
WLAN LED (option) It displays whether the wireless WLAN power gets supply.
Battery latch You can attach and detach by moving it from side to side.
battery It attaches on body for receiving power.
Scan key You can scan the barcode or RFID tag by this buttons.
Speaker It is equipped for playing sound and various sound eects internally.
Sync cable connector It makes device transmit and receive the data with computer in connection with USB sync cable.
Earphone jack It is used for connecting the earphone with device.
Charger LED It will be changed with red color in charging state / with green color in full.
DC Power Port Please do connect it with provided adapter when charging the device.
Camera ash (option) It functions in case of using camera.
Camera (option) It makes image capture and save.
Keypad It makes device implement the program and input the key value by using input key.
Touch screen You can implement and terminate the program to touch the screen by using stylus pen.
Hand strap hole Please attach hand strap and stylus pen with device for your convenience when using it for a long time.

10Chapter 3. Basic Function
Basic Function
Attaching and Detaching the battery
▶Battery detachment
These images as below, shows the back bottom of the PDA.
Slide the battery latch to the right (UNLOCK side), and then lift the battery out of the compartment along both sides of groove.
PDA is composed of battery. The battery supplies the power to the system and RAM which can save and conserve the data.
Battery: 3.7V 2,200mAh Lithium-Ion
Attach the battery to the back battery compartment of the PDA.
Push the batter lever inside so that the battery is rmly attached to the PDA.
“Refer to 1.1 Battery attaching and detaching”
Connecting adaptor to the PDA adaptor connecting jack, and check if the “Power LED” is Red, and then charging the power completely until it turns into Green.
◆Note:
When the desktop screen shows after starting the system, press the <power> button for a couple of seconds can reduce the recharging time.
Battery locking lever

▶Battery attachment
Put the top part of battery into the upward groove, and then press down the bottom of battery into the battery compartment, slide battery latch to the left
(LOCK side) to attach battery rmly
Chapter 3. Basic Function 11
Above gap for attachment/
top of battery

12
Charging battery
▶Connecting Adapter
1. Plug in the adapter into the 220V socket.
2. Connect the Mini USB jack to the PDA’s “Sync cable connector”
3. When “Power LED” shows red light, it means that the device is being charged.
◆Caution:
You must to charge the device using dedicated adapter that is provided from the manufacturer, or your device might get damaged.
Low power mode (Sleep mode)
Power o (setting sleep mode):
If the power button is pressed when the device is on, the screen will be turned o and the device will enter the low power mode (sleep mode).
Power on (releasing sleep mode)
If the power button is pressed when the device is o, the screen will be turned on and the device will be turned on.
▶Setting low power mode (sleep mode) by Power ON/OFF button
You have to charge the battery via dedicated adapter, which provided from the factory.
“Power LED” is Red while charging or is Green when charged completely. When fully charged, the LED light will be turned o.
When the system is started and shows the main desktop screen or other programs are running, you can enter into the low power mode (sleep mode)
by using the power button. If you want to use the device again, press the power button again and turn on the system
Chapter 3. Basic Function

13
If the user doesn’t use the device for a set period of time, system enters into the low power mode (sleep mode) automatically. You can change
the setting time in control panel and power management as shown below. Using proper time-out setting prevents the system is on a long time
without the user and extends hours of battery use.
[Menu] -> [Application] -> [Settings] -> [Display] -> [Sleep mode]
▶Automatic Power OFF
Chapter 3. Basic Function
▶Batter replacement
If the batteries are damaged or out of its life, buy new batteries to use.
■Warning!
Discard the dead batteries to the designated place
▶ Turn off the device in case of discharging the battery
If the system cannot be used by electric discharge, it will be automatically entered into low-power mode (sleep mode). In this case, user have to charge the
battery or connect the adaptor with the adaptor connecting jack of main body, then press the <Power> button to turn on the system since it won`t be turned on
despite of pressing the <POWER> button.

14
If the system is not responding or application program doesn’t work, restart the system by using reset function.
System reset is used to reboot and initialize the hardware completely. The installed programs copied les, and registry values will be preserved even after
the system reset
[Process of hard reset]
Push and release the reset button.
[Result of Hard Reset]
-The system will restart.
-The operating system will be loaded again when restarting.
Hard reset
Chapter 3. Basic Function

15
SIM card slot
release the lock.
Slide the cover of Micro SD
card slot to the right to Lift up the top of the slot
cover to open
Place the SD memory card
into the slot and close the
cover
Slide the cover to the left to
lock the slot.
Attaching Micro SD card
The image below shows the back side of the PDA when the battery is removed.
There are 1 SIM card slot, 1 Micro SD memory card slot as shown below.
Micro SD card slot
Chapter 3. Basic Function

16
When the SD memory is selected from the File Manager after installing Micro SD memory card, it is shown as below.
Attaching SIM card
Chapter 3. Basic Function
Below is the screenshot after installing the SIM card.
Place and insert the SIM card so that it ts the slot shape.

17
Brightness of the screen aects the power consumption the most, so it is recommended to be set as required by the user.
[Setting the screen brightness]
1. [Menu] -> [Settings] -> [Display] -> [Brightness]
Wallpaper: Choose the wallpaper.
Auto-rotate screen: Set the Auto-rotate screen function.
Sleep mode: Adjust the time period to enter into the sleep mode
Set screen brightness
Brightness: Adjust the screen brightness.
Font size: Adjust the font size of PDA.
Chapter 3. Basic Function
The volume is set to 80% when it is dispatched. The user can set the dierent features of sound settings from [Menu] -> [Settings] -> [Sound].
Volumes and sound setting
[Menu] -> [Settings] -> [Sound]
Volume setting

18Chapter 3. Basic Function
Keypad is an input method editor that inputs numbers or alphabetic characters easily.
To change the current input language, follow the steps below.
[Menu] -> [Settings] -> [Language & input]
Using keypad
Describe the Keypad Function.
Keypad button execution
Keypad Function description
Menu key
Contains keyEvent values of KEYCODE_SOFT_RIGHT.
It is used to move back to previous state.
It is used for searching.
Home button.

19
Optional module
This chapter describes various option modules for use with AT911N.Please refer to description of necessary option modules and use them.
Option module for AT911N
Various optional modules for AT911N
1) Barcode reader
-. 1D Laser Barcode Scanner
-. 2D Imager Barcode Scanner
2) Wireless LAN – 802.11 a/b/g/n
3) Bluetooth
4) UHF 900MHz RFID – ISO18000-6C
5) GPS Module
6) Phone
7) Camera
AT911N device provides the options as below according to the purpose of use. The Option Modules below are other specications outside AT911N, so when
buying the device, you should conrm it to buy.
Chapter 4. Optional module

20
The barcode scanner which can recognize 1D, 2D barcode can be installed on this device.
Using 1D or 2D barcode scanner
[Menu] -> [Application] ->
[ATID Barcode]
Chapter 4. Optional module
ATID Barcode demo