Atid AT870N Reference guide

Guide for Customer
AT870N

2
ATID is a registered trademark of ATID CO.LTD.
AT870N is a registered trademark of ATID CO.LTD. and of its wholly owned subsidiaries.
Microsoft Windows®, Windows® 2000, Windows® CE .NET, Windows® NT, and Windows® XP are registered trademarks of Microsoft Corporation.
ATID CO.LTD.
Disclaimer
#1211 Byuksan/Kyungin Digitalvalley 11, 184, Gasan digital 2-ro, Geumcheon-gu, Seoul, Korea
Tel: [phone]
Fax: [phone]
www.atid1.com

3
Contents
Page Contents
5 Before using manual for AT870N
Chapter 1. Caution when using AT870N
6 1. How to use battery correctly
6 2. Caution when using AT870N
Chapter 2. Product composition
7 1. Product composition
8 2. Name of each part
9 3. Function of each part
22 16. Data and time setting
Chapter 3. Basic function
10 1. Switch OnBackup Battery
11 2. Attaching and Detaching the battery
12 3. Charging battery
12
14 5. Checking Battery Gauge
15 6. Backup Battery
15 7. Battery replacement
16 8. SoftReset
16 9. HardReset
17 10. Initializing System
19 11. Attaching Micro SD card
20 12. Attaching SIM Card
21 13. Screen brightness setting
21 14. Screen adjustment
22 15. Volume and sounds setting

4
Page Contents
Chapter 3. Basic function(continues)
24 17. Using keypad
24 18. Inputting Data
25 19. Using <Fun> Button
20. Use of stylus
26 21. Connecting PDA to PC
28 22. Data transfer
29 23. Firmware upgrading
Chapter 4. Optional module
31 1. Using 1D or 2D barcode scanner
32 2. Barcode emulator setting
34 3. Barcode symbology setting
36 4. Barcode scanning
37 5. WLAN connection and termination
39 6. Bluetooth connection and termination
41 7. Bixolon SPP-R200 Printer Demo
42 8. GPS demo program execution
43 9. Use of camera
44 10. HF13.56 demo program execution
44 11. Mifare tag recognition
45 12. ISO15693 tag recognition
46 13. UHF 900Mhz Program
47 14. Modem ON/OFF
Chapter 5. Appendix
48
25

5
■
◆
●
Before using manual for AT870N
Safety information
Please read and follow all warnings and cautions for user`s safety in this document before you handle and operate ATID equipment.
WARNING!
A warning requires that you must strictly pay attention to operate procedure, practice, condition, and state, or might be injured seriously.
CAUTION
A caution explains the important point which has a huge possibility to break the device and make a malfunction
NOTICE
User guide inclusive of text, images, logos, product names is either the property of, or used with permission by ATID CO.,LTD. The information may not be distributed,
tten permission of ATID CO.,LTD
en user guide and actual function of device
User guide can be adjusted by ATID CO.,LTD without consent of user discretionally.
User guide is written for users who want to use and maintain the AT870N. Please read and understand these instruction prior to operating this unit.
A notice provides you with needed additional information while using AT870N.
Do not expose your device to extreme temperatures lower than - 10°C and higher than + 40°C.
Distance of operation
When using a data feature, position the phone a minimum of 0.5 cm from your body for the whole duration of the data transmission.
Adapter
Adapter shall be installed near the equipment and shall be easily accessible.
Manufacture：ATID CO., LTD
Model No.: BPI020S05N03
I/p: 100-240V～50/60Hz ,MAX/0.5A
O/p: 5V 3A
The plug considered as disconnect device of adapter
Battery Caution
Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
Proper use
As described in this manual, your device can be used only in right location. If possible, please do not touch the antenna area on your device.
The product shall only be connected to a USB interface of version USB2.0
Regulatory Conformance Hereby, ATID CO.,LTD. declares that this device is in compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC

6Chapter 1. Caution whenusing AT870N
•
Caution when using AT870N
Please aware of the manual contents in advance before you handle and operate your AT870N and other ATID Products.
How to use battery correctly
In case that you dropped the main body or battery in water, please do not put into the stove or heater for drying. Just keep it in natural drying or contact purchase
place.
Please note that the battery terminal doesn’t have to be contacted to metallic object.
If you do not use the battery for a long time, please keep it at room temperature after charging.
Operating time of battery can be shorter than usual in accordance with loss of battery and use time. In this case, please contact us.
You have to use provided adaptor when charging the device.
Turn o the device properly then detach or replace the battery.
Caution when using AT870N
separately.
If you habe a problem on product, do not try to repair or disassemble it by yourself, please contact our customer service center.
r.
Please note thatusing the device in environment of high temperature and humidity for long hours can make a malfunctionof device.
•
•
•
•
•
•
•
•
•
User careless or products repair would damage the stored data. Manufacturer is not responsible for this damage, so please do back-up the important data
•
•
I the power immediately, then
please contact ourcustomerservice center.
If you have any other questions on use of device, please contact our customer service center.

7Chapter 2. Product composition
Product Composition
Product composition
*Please contact our customer service in defect of product composition and need to be changed.
5.
3. Standard battery
6. Hand strap
2. Power Adapter and AC cable
1. AT870N main body
4. USB sync cable
AT870N is based upon Microsoft window CE 5.0 and as the state of the art product.
it is equipped with barcode scanner, RFID Tag reader, MSR card reader, printer, smart card reader, MODEM, Camera and so on and it can be applied to Industry, Enterprise,
7. Stylus pen

Camera (option)
Camera ash
(option)
Cradle connector
Earphone jack Charger jack
Sync Cable
Connector
Phone receiver WLAN LED
(option) Internal HF
Charge LED
Touch Screen
Keypad
Reset button Microphone
UHF
Scan button (F7,F8)
Gun handle
1D/2D Scanner
(option)
8Chapter 2. Product composition
Name of each part
Battery latch
Hand strap hole
Battery
Volume button
UHF Connecting
port

9
Function of each part
Chapter 2. Product composition
NAMEFUNCTION
Enable you to connect to adaptorwhich provided from factory.Charger jack
Enable you to connect to PC or charging the battery while using cradle.
Cradle connector
Camera (option) Itis possible toimage capture and save.
Earphone jack Enable youto connect to earphone.
Enable youto connect and send data to PC via USB synccable.Sync cable connector
Charger LED willbe Red whenthe battery is charging, or will be greenwhenitischargedcompletely.Charger LED
Enable youto input key value (number, alphabets, symbol), or executing assignedprograms.Keypad
Display running programs, and could execute, use, and exitprogramsvia to touch the screen.Touch screen
Enable you to perform awarmReset, Press <Power>button simultaneously, Enable you to perform ahard ResetReset button
Displays whetherthe wireless WLAN power supply
WLAN LED (option)
Laser beamemittedthroughthis window. Please be careful the foreignsubstances and preventing fromthe damage.
Warning! Donotlook at the laser beam directly.
1D/2D Scanner (option)
Internal HF HF13.56MhzEmbeddedmodule mounting location.
Enable youto attacha hand strap or astylus for the convenience of using, while need to use the device foralong period time.Hand strap hole
Enable you to conduct communicationMicrophone
Enable you to detaching and attaching the main battery.Battery latch
Enable to supply the power to the product.Battery
Itis possible toscan barcode or RFID tagScan button (F7, F8)
Enable youto install aUHF 900Mhz tag reader module.UHF Connecting port

10Chapter 3. Basic Function
Basic Function
Switch On Backup Battery
Battery for AT870N is composed of main battery and backup battery. A main battery supplies the power to the system and RAM which could keep the data.
A backup battery could keep the data of RAM when the main battery discharged completely.
Main Battery: 3.7V 2,960mA Lithium - Polymer
Backup Battery: 3.7V 80mA Lithium - Polymer
◆Note:
Please switch on the back-up battery as below instruction in advance at the beginning then, attach the main battery to body and then,
charge it in full before using the product
◆Note:
Please press the <POWER> button a couple of seconds for shortening the charging time, in case of that window screen has shown.
The image as below shows the status of battery compartment on the rear of body
Please slide the switch of backup battery to right for switching on the device.
If the switch turns on, the power of battery will supply to the system.
Please attach the main battery on the rear of body.
Please attach the main battery to the body by moving the latch lever in case of attaching the battery.
Please refer to section 1.2 of attaching and detaching the battery
Please connect the charger with charger jack and then do check if red light is lit on the LED.
Please charge it until the green light is lit on the LED
Backup Battery Switch

11Chapter 3. Basic Function
Attaching and Detaching the battery
▶Battery detachment
Below images are shown the bottom of device
Please slide the battery latch to the right (Direction to UNLOCK), and then lift the main battery to detach the main battery after grapping the laver at the bottom.
▶Battery attachment
Please put the top of the battery into the above gap of device and then, push the bottom of battery into the below gap of device and then, slide the lever
to right (Direction to LOCK).
Above gap for attachment/
top of battery
Battery Latch Both Side of the Gap

12
▶Connecting Adapter
1. Connectthe adapter plug with 220V socket
2. Connectadapter DC cable with “Power Connecting Jack”
3. LED will be changed when the red light is lit onthe LED
◆Caution:
You must use provided adapter with device. Otherwise your device might be damaged
You have to charge it through dedicated adapter which is provided when you bought
Red light is lit on LED when it starts charging. It will be changed with green light in case of full
Chapter 3. Basic Function
In case of that there is window screen as below or you don`t use the system in the status of running other program, the device is able to enter
the low-power mode (Sleep mode) If you want to use it again, please press the <POWER> button
Start button
Taskbar
Taskbar : Displayed section of running program
Start button : Initial button for starting the program which you want to activate
Charging battery

13
The device will be automatically entered to low-power mode (Sleep mode) if user does not use it for the designated time.
User can change the designated time at the control panel and power as below. If user sets proper time-out,
the device can be protected from the situation of power-on without user and battery can be prolonged.
▶Automatic Power OFF
Chapter 3. Basic Function
▶
Power Button
1. If you push the <POWER> button for 2 ~3 seconds in the state of running on the screen,
Power On:
1
2. The system will be automatically turned on when ActiveSync USB cable is connected with device.
◆Note:
and these programs will be recovered in case of power-on.
If both main battery and backup battery are in the discharge state, the RAM data will disappear,
and the system will be re-starting if the power is charged again.
Please do not afraid that you will enter the above situation in case of double-click on Icon of POWER indication
The system can be turned on in case of entering the low-power mode by Automatic Power-OFF
Power Icon

14Chapter 3. Basic Function
▶BatteryDischarging
The system is automatically going to enter the low-power mode (Sleep Mode), if the system is not available due to dead battery. In this situation,
the system cannot be turned on despite of pushing <POWER> button If the system enters low-power mode (Sleep mode) due to dead battery,
user is able to turn on the device by pushing <POWER> button after plugging the adapter in adapter jack or charging the main battery.
Checking Battery Gauge
◆Note:
In general, you can use the device from 6 hours to 12 hours after 2200 mA battery is fully charged.
▶Checking BatteryGauge
[Start Button] -> [Setting] -> [Control Panel] -> [Power Management] -> [Battery]

15Chapter 3. Basic Function
▶Low Power Warning
If the system is unavailable for low-battery, caution screen for lack of battery will be came out.
Backup Battery
◆Caution:
RAM data will be disappeared if both main and back-up battery completely discharge.
Activated RAM data will be disappeared at the running program and the system
will restart in case of inputting the power instead of recovering.
Back-up battery can be used for protecting the RAM data in case of discharging the main battery
Battery replacement
◆Warning!
Please discard the expired battery at the designated location
You need to purchase a new battery if existing battery got damaged or reached to its life

16
[Process of Soft Reset]
Please press the Reset button which is located on the device with stylus pen for a moment.
The system will be restarted after turning o the screen a moment automatically.
[Result of Soft Reset]
-System will be restarted.
-OS will be restarted.
Soft Reset
Chapter 3. Basic Function
Please do restart the system when the application doesn`t work properly or system receives no Response
When do you need to perform Soft Reset?
-Screen will be reshown after 10 seconds
-Adjusted registry information,
copied le and installed program will be remained Reset button
Power Button
When do you need to perform Hard Reset?
[Process of hard reset]
Please press the Power button and reset button with stylus pen simultaneously and then, unhand those buttons.
[Result of Hard Reset]
Hard reset
Hard reset which is called cold reset can be used for initializing the hardware completely.
Registry value, copied le and installed program can be remained originally even though user uses the hard reset, but please note that time/date will be initialized.
Therefore, please do reset the time if user uses the hard rest Please use hard reset if it is impossible to recover the system despite of soft reset
-System will be restarted.
-OS will be restarted.
-Screen will be reshown
-There are setting screen of time / date and user have to reset the setting og time and date.
There is a Hang-up, which means that the system receives no response in case of running the program.
When user encounters Hang-up, please do reset the system for recovering the device.
Please note that warm reset can make the program terminate and clear the using memory.
But it doesn`t inuence on installed program and data etc.

17
Initializing System
Chapter 3. Basic Function
Please use [Boot Menu] when user encounters below situation
1. When user wants to recover the adjusted registry information back again.
2. When user wants to initialize the storage space inside the “My Computer”
3. When user wants to initialize the storage space inside the “Flash Disk”
4. When user wants to make system a comeback as the state of beginning
Press <POWER> button and <FUN> button simultaneously and then, press <RESET> button
Reset Button
Power Button
FunButton
[Boot Menu] is came out at the screen as below after 2 ~ 3 seconds
◆Caution:
Do not use any other functions except for [Clean System] at the [Boot Menu]
There is a huge possibility to do abnormal movement if you use other functions
[Boot Menu]
[System Information]
[Firmware Upgrade]
[Clean System]
Select: Enter
[Boot Menu] Initial Screen
[Boot Menu]
[System Information]
[Firmware Upgrade]
[Clean System]
Select: Enter
Select the <Clean System> by
using <8> button and <2>
button and then, press <Enter> button
[Exit Boot Menu]
Move : 2(Up)/8(Down)
[Exit Boot Menu]
Move : 2(Up)/8(Down)

18Chapter 3. Basic Function
[Boot Menu]
[Clean System]
Select : Enter
Select the clause > by using <8>
button and <2> button. Please
note that you can go back to the
main menu if you press <BKS> button
[Boot Menu]
[System Information]
[Firmware Upgrade]
[Clean System]
[Conguration Setting]
Select : Enter
Select the [Exit Boot menu] by using
<8> button and <2> button and
then, press the <Enter> button to get
out of [Boot Menu]
Preview : <- BKS
[Exit Boot Menu]
Move : 2(Up)/8(Down)
Clean Registry
It makes registry as initial state
Clean OS Root
It makes “My Computer” as initial state
Clean Flash Disk
It makes “Flash Disk” as initial state
Factory Reset
It makes the device as factory default
Clean Registry
Clean OS Root
Clean Flash Disk
Factory Reset
Move : 2(Up)/8(Down)

19
Do unlock the Micro SD
CARD by sliding the card
slot cover right side
Lift the slot cover up Put the SD memory on the
slot and then, shut the cover up
Do lock the slot cover by
sliding it left side and then,
turn on the device after
installing the battery
Attaching Micro SD card
Below image shows the back side of device when separating the main battery from device There are 1EA SIM Card Slot and 1EA Micro SD Card Slot.
Micro SD card slot
Chapter 3. Basic Function
SIM card slot

20
Attaching SIM Card
Chapter 3. Basic Function
Below image shows the state of equipping the SIM CARD with device. Please do insert it in accordance with card shape and edge shape