Atlas Copco RTX-30 User manual

RTX-30
TORQUE CHART
This chart shows the correlation
between pump gauge psi reading
and torque output for your Rapid-Torc
RTX-30 hydraulic torque wrench.
PSI FT.LB.
1500 4770
1600 5088
1800 5724
2000 6360
2200 6996
2400 7632
2600 8268
2800 8904
3000 9540
3200 10176
3400 10812
3600 11448
3800 12084
4000 12720
4200 13356
4400 13992
4600 14628
4800 15264
5000 15900
5200 16536
5400 17172
5600 17808
PSI FT.LB.
5800 18444
6000 19080
6200 19716
6400 20352
6600 20988
6800 21624
7000 22260
7200 22896
7400 23532
760 0 24168
7800 24804
8000 25440
8200 26076
8400 26712
8600 27348
8800 27984
9000 28620
9200 29256
9400 29892
9600 30528
9800 31164
10000 31800
BAR NM
104 6467
110 6898
124 7761
138 8623
152 9485
165 10348
179 11 2 1 0
193 12072
207 12935
220 13797
234 14659
248 15521
262 16384
276 17246
290 18108
303 18971
317 19833
331 20695
345 21558
358 22420
372 23282
386 24144
BAR NM
400 25007
414 25869
427 26731
441 27594
455 28456
468 29318
482 30181
496 31043
510 31905
524 32767
538 33630
552 34492
565 35354
579 36217
593 37079
607 37941
620 38804
634 39666
648 40528
662 41390
676 42253
690 43115
2
Set the pressure on the pump that
corresponds to the torque value.
1Find the closest torque value for
your application, either in ft-lbs
or in Nm.
FOOT-POUNDS NEWTON-METERS
The above torque values are only applicable when using a calibrated RTX-30 hydraulic torque wrench powered by a 10,000 psi
pump fitted with a calibrated class 1 gauge.
RT-PTCen-RTX-30 Copyright Rapid-Torc®. Part of the Atlas Copco Group Revised October 2014

QUICK SETUP
GUIDE
Setting up your hydraulic torque wrench for use is easy.
Please read the included user manual and safety instruc-
tion booklet for additional guidelines.
1
FOUR BASIC STEPS TO OPERATE YOUR RTX-30
4
Scan the code to see a brief overview video on how to use the document or go to
rapidtorc.com/torque_setup
RT-PTCen-RTX-30 Copyright Rapid-Torc®. Part of the Atlas Copco Group Revised September 2014
Wear personal protec-
tive equipment, such as
eyeglasses and steel-toe
shoes.
1
2
3
SET PRESSURE
Make sure the hoses are
free of any defects. The
couplers are on pump
and the tool should be
securely connected.
Place tool on at surface.
Turn pump on. Cycle the
tool. Press the “ON’ but-
ton on the remote, hold
until tool clicks. Release,
wait for the tool to click.
Repeat the cycle. Ensure
there is no leak.
4
Use the torque conver-
sion chart to set the psi
for the torque you need.
Press the remote’s “ON”
button and slowly turn
the pressure regulator
clockwise to reach the
right pressure.
CYCLE YOUR TOOL
CONNECT HOSES
WEAR PPE
2
3