Atlas Escalateurs VISTA User manual

INSTALLATION MANUAL
VISTA

INSTALLATION OF THE PROTECTION WALL.
(PROVIDED BY THE CONTRACTOR)
-PROTECTION WALL NEEDS TO BE THE SAME WIDTH
THAN THE UPPER LANDING GATE THRESHOLD.
-PROTECTION WALL NEEDS TO BE LEVELED.
MAKE THE HOLE FOR THE
UPPER LANDING GATE
THRESHOLD.
3 1
2
"
R,375
42 5
16
" FOR 34'' UPPER LANDING GATE.
INSTALLATION MANUAL
VISTA
1
DETAIL A
1/8'' DEPTH
DON'T FORGET THAT THE PLATFORM
NEEDS TO BE ALIGNED WITH THE INTERLOCK.

110V PLATE
POWER: 110V-20 AMP
B
DÉTAIL B
ECHELLE 1 : 8
FLUSH WITH THE PROTECTION WALL.
ON THE LANDING
INSTALLATION MANUAL
VISTA
INSTALLATION OF THE UPPER LANDING GATE.
(SEE DETAIL B)
2
DETAIL B

#12-2'' LG SCREW
USE SHIMS IF
NECESSARY
INSTALLATION MANUAL
VISTA
-ADJUSTEMENTS OF THE UPPER LANDING GATE.
-LEVEL THE PLATFORM.USE SHIMS IF NECESSARY.
-SCREW THE SILL WITH WOOD SCREWS #12-1.5'' TO 2'' LG.
(TOTAL 18 SCREWS-PROVIDED BY THE INSTALLER)
3

A
-OPTIONAL GATE OPERATOR.
-IF REQUIRED FOR WIRING,MAKE A HOLE
IN THE FLOOR.
-SEE INSTALLATION MANUAL FOR GATE
OPERATOR.
DÉTAIL A
ECHELLE 1 : 8
1'' HOLE IN THE FLOOR
INSTALLATION MANUAL
VISTA
-MAKE A 1'' HOLE FOR THE WIRING IN THE FLOOR.
(INTERLOCK SIDE)
-PASS THE WIRING FROM THE GATE INTO THE PLATFORM.
(SEE DETAIL A)
4
DETAIL A

-INSTALL THE PLATFORM AT THE RIGHT PLACE.
-USE 1'' DIAMETER STEEL RODS TO MOVE IT EASILY.
1'' STEEL RODS
OPTIONAL
GATE OPERATOR
PLATFORM GATE COMES IN OPTION WITH THE INTERLOCK.
INSTALLATION MANUAL
VISTA
5

COVER WITH THE 4 BOLTS.
FACADE
PLATFORM GATE WITH THE INTERLOCK IN OPTION
INSTALLATION MANUAL
VISTA
UNSCREW 4 COVER BOLTS TO REMOVE THE COVER
AND THE FACADE.
6

A
B
C
1-ALIGN PLATFORM WITH UPPER LANDING INTERLOCK(SEE DETAIL A)
2-PLACE UNIT 0.6''-1'' FROM THE PROTECTION WALL.
3-BRING POWER (110V) TO THE PLATFORM (SEE DETAIL C)
4-OPEN THE DISCONNECT AND PULL DE THE E-STOP.
DÉTAIL A
ECHELLE 1 : 10
DÉTAIL B
ECHELLE 1 : 10
DÉTAIL C
ECHELLE 1 : 10
INSTALLATION MANUAL
VISTA
DETAIL B
DISCONNECT (MAY BE DIFFERENT FOR
COMMERCIAL/RESIDENTAL APPLICATION)
DETAIL C
PIT E-STOP
7
DETAIL A

A
DÉTAIL A
ECHELLE 1 : 9
INSTALLATION MANUAL
VISTA
DO 1 COMPLETE TRAVEL TO CHECK IF THERE ARE INTERFERENCE.
CHECK THE MIN. AND MAX. CLEARANCE BETWEEN THE PLATFORM
AND THE PROTECTION WALL. (SEE DETAIL A)
8
DETAIL A
15 À 25 mm

DO THE ANCHORING HOLES IN THE SLAB
AND THEN INSERT THE ANCHORS.
(TIGHTEN THE 3/8'' X 3-3/4'' LG ANCHORS
TO 25 LB-PI)
ALUMINUM SHIMS IF NEEDED.
INSTALLATION MANUAL
VISTA
-DO THE LAST FIXINGS:
-INSERT SHIMS UNDER THE PLATFORM LEGS TO LEVEL THE UNIT.
(PROVIDED BY THE INSTALLER)
-SCREW THE LEGS IN THE CONCRETE SLAB.
(3 SCREW BY LEGS)
9