Atlona AT-LINE-PRO2 User manual

www.atlona.com
Toll free: 1-877-536-3976
Local: 1-408-962-0515
User Manual
CV/SV/PC/HD/HDMI 1080p
Scaler Box
AT-LINE-PRO2

1www.atlona.com
Toll free: 1-877-536-3976
Local: 1-408-962-0515
1. Introduction .................................................. 2
2. Features .................................................. 2
3. Package Contents .................................................. 2
4. Operation Controls and Functions .................................................. 3
4.1 Front Panel .................................................. 3
4.2 Rear Panel .................................................. 4
4.3 OSD Operation .................................................. 5
4.4 Remote Control .................................................. 6
5. RS-232 Remote Control Protocol .................................................. 7
6. Specifications .................................................. 11
6.1 General Specification .................................................. 11
6.2 Support Resolution .................................................. 11
7. Safety Information .................................................. 13
8. Warranty .................................................. 14
9. Atlona Product Registration .................................................. 15
TABLE OF CONTENTS

2www.atlona.com
Toll free: 1-877-536-3976
Local: 1-408-962-0515
Atlona Scaler Box is designed to upscale digital/analog video signal from Composite, S-Video, PC, Component
(HD) and HDMI input sources, to digital HDMI output of wide-range HDTV and PC resolutions, up to 1080p
and WUXGA (1920 x 1200.) Besides video upscaling, the scaler box also converts digital/analog audio signal
to digital format, then output either through HDMI combining with the video, or Coaxial S/PDIF separately.
AT-LINE-PRO2 has a comprehensive OSD menu that allows user to select a variety of output resolutions and
adjust for best picture quality.
• HDMI 1.2, HDCP 1.1 and DVI 1.0 compliant.
• Scales any PC (VGA ~ WUXGA) /HD (480i ~ 1080p) resolutions to/from another PC/HD resolutions.
• Automatically detect the factory setting of the connected display and output the corresponding resolution
and refresh rate, when the NATIVE output is selected.
• Supports 50/60Hz frame rate conversion.
• Supports 3-D motion video adaptive, 3-D de-interlacing, and 3:2 / 2:2 pull-down detection and recovery.
• Provides output picture adjustment on contrast, brightness, hue, saturation, sharpness, RGB (color tone)
level, and aspect ratio size.
• Supports high resolution input/output:
PC: VGA, SVGA, XGA, SXGA, UXGA, WXGA, WSXGA, WUXGA
HDTV: 480i, 576i, 480p, 576p, 720p, 1080i, and 1080p
• Supports digital and analog audio input and output.
• Atlona AT-LINE-PRO2 Scaler Box
• D-Sub (15pin) Cable
• 3XRCA Cable (Composite Video + L/R Audio)
• Remote Controller
• 5VDC Power Supply Adaptor
• Operation Manual
INTRODUCTION
FEATURES
PACKAGE CONTENTS

3www.atlona.com
Toll free: 1-877-536-3976
Local: 1-408-962-0515
4.1 Front Panel
1. POWER Button and LED Indicator:
Press the button to turn ON/OFF the power of the unit. The LED will illuminate when the power is
turned on.
2. IR remote control sensor.
3. Input Selection Buttons and LED Indicators:
Press each of the buttons (CV/SV/COMP/PC/HDMI) to select the desired input source.
The LED will illuminate when the corresponding input is selected.
4. MENU Button:
Press the MENU button to bring up OSD operation menu (see section “4.3 OSD Operation”for reference.)
5. +/- Buttons:
On the first tier of OSD menu, use + and - buttons to move up/down the highlight item for selection.
b. Once the desired option is selected, use + and - buttons to toggle between setting values.
6. ENTER Button:
In OSD menu, use the ENTER button to confirm the selection
OPERATION CONTROLS AND FUNCTIONS
1 2 3 4 5 6

4www.atlona.com
Toll free: 1-877-536-3976
Local: 1-408-962-0515
4.2. Rear Panel
1. HDMI OUT and CO-AX OUT:
Connect the HDMI OUT port to the HDMI input port of your display such as HDTV. Connect the CO-AX
OUT port to the Coaxial (S/PDIF) input port of your amplifier for separate digital audio output.
2. AUX IN Input:
When the video signal input through the HDMI IN port is from a DVI source such as a PC, use the AUX IN
port to input the audio signal.
3. HDMI IN Input:
Connect the HDMI IN port to the HDMI output port of your source equipment such as DVD player or Set-
Top-Box. Or, use HDMI to DVI cable to connect to the DVI output of your PC.
4. RS-232:
Used for remote control and firmware updates.
5. PC IN for Video and Audio Input:
Connect the PC IN D-Sub (15-pin) port to the D-Sub output port of your PC. And, connect the PC IN
3.5mm phone jack to the audio output port of your PC.
6. Y Pb/Cb Pr/Cr Video and L/R Audio Input:
Connect the Y Pb/Cb Pr/Cr (Component) 3 RCA input ports to the Component output port of your video
source equipment such as DVD player or Set-Top-Box. And, connect the L/R audio input ports to the au-
dio output port of your audio source equipment.
7. CO-AX Input:
The CO-AX port provides the digital audio input support, and can be used to combine with each video
input signals from CV/SV/COMP/PC/HDMI ports. Once connected, please use the Audio Source Selection
in the OSD menu to select between Coaxial (S/PDIF) or other audio source (see section “4.3 OSD Opera-
tion” for reference.)
8. Composite Video / S-Video and L/R Audio Input:
Connect the Composite or S-Video input port to the Composite or S-Video output port of your video
source equipment such as DVD player or Set-Top-Box. And, connect the L/R audio input ports to the au-
dio output port of your audio source equipment.
9. Power:
Plug the 5VDC power supply into the unit and connect the adaptor to AC wall outlet.
1 3 5 6 8 9
742

5www.atlona.com
Toll free: 1-877-536-3976
Local: 1-408-962-0515
4.3. OSD Operation
1st Tier Option 2nd Tier Option Adjustment
VIDEO PICTURE MODE USER / STANDARD / VIVID / MOVIE
CONTRAST 0 ~ 100 of Contrast Level
BRIGHTNESS 0 ~ 100 of Brightness Level
HUE 0 ~ 100 of Hue Level
SATURATION 0 ~ 100 of Saturation Level
SHARPNESS 0 ~ 100 of Sharpness Level
SCALE OVERSCAN / UNDERSCAN / LETTERBOX / PANS-
CAN / FULL
NR LOW / MIDDLE / HIGH / OFF
EXIT Back to the 1st Tie
COLOR COLOR TONE USER / NORMAL / WARM / COOL
RED 0 ~ 100 of Red Color Level
GREEN 0 ~ 100 of Green Color Level
BLUE 0 ~ 100 of Blue Color Level
EXIT Back to the 1st Tier
OUTPUT - NATIVE / VGA / SVGA / XGA / SXGA /UXGA / 480i
/ 480p / 720p@60Hz / 1080i@30Hz / 1080p@60Hz
/ 576i / 576p / 720p@50Hz / 1080i@25Hz /
1080p@50Hz / WXGA / WSXGA / WUXGA
OSD HPOSITION 0 ~ 100 of OSD Horizontal Position
VPOSITION 0 ~ 100 of OSD Vertical Position
TIMER 0 ~ 100 of OSD Show Time (sec.)
TRANSP 0 ~ 100 of OSD Transparent Level
EXIT Back to the 1st Tier
AUDIO SOURCE HDMI / L/R / COAXIAL
DELAY OFF / 40MS / 110MS / 150 MS
SOUND ON / MUTE
EXIT Back to the 1st Tier
INFORMATION - SOURCE (Input interface)
INPUT (Input Resolution)
OUTPUT (Output Resolution)
VERSION (Firmware Version)
EXIT - Close the OSD Menu

6www.atlona.com
Toll free: 1-877-536-3976
Local: 1-408-962-0515
4.4. Remote Control
1. POWER:
Press the button once to power on the AT-LINE-PRO2.
Press again to enter standby mode.
2. INPUT:
Press the button repeatedly to toggle through various input sources.
3. HD Input:
Press the button to directly select component input.
4. PC Input:
Press the button to directly select PC input.
5. HDMI/DVI Input:
Press the button to directly select DVI (or HDMI) input.
6. Output Resolution:
Press any one of the button to directly select output resolution.
For other output resolutions that are not covered by these buttons
please enter OSD Menu to select them.
7. MENU:
Press the button to bring up OSD main menu page.
8. Exit:
Press the button to exit from a sub menu or main menu.
9. Up/Down/Left/Right:
Press the Up/Down button to move the highlight bar to your desired parameter during the OSD opera-
tion. Press the Left/Right button to increase/decrease the setting value of a selected parameter.
10.OK (Enter):
Press the button to confirm your selection.
11.Reset:
Press the button to reset the unit’s firmware setting to the factory default value.
12.Auto Adjust:
Press the button to optimize the position of the picture (picture centering) on the screen

7www.atlona.com
Toll free: 1-877-536-3976
Local: 1-408-962-0515
* The connection between AT-LINE-PRO2 and remote controller with RS-232 modem cable.
Pins definition of modem cable
AT-LINE-PRO2 Remote Controller
PIN Definition PIN Definition
1 NC 1 NC
2 TxD 2 RxD
3 RxD 3 TxD
4 NC 4 NC
5 GND 5 GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
* RS-232 transmission format:
Baud Rate: 19200 bps
Data Bit: 8 bits
Parity: None
Stop Bit: 1 bi
LINE-PRO2 RS-232 REMOTE CONTROL PROTOCOL

8www.atlona.com
Toll free: 1-877-536-3976
Local: 1-408-962-0515
(A) Set Commend:
Command Code Response Description
S POWER 0 > POWER OFF POWER OFF
S POWER 1 > POWER ON POWER ON
S SOURCE 0 > SOURCE CV CV INPUT
S SOURCE 1 > SOURCE SV SV INPUT
S SOURCE 2 > SOURCE COMP COMP INPUT
S SOURCE 3 > SOURCE PC PC INPUT
S SOURCE 4 > SOURCE HDMI HDMI INPUT
S OUTPUT 0 > OUTPUT NATIVE NATIVE RESOLUTION OUTPUT
S OUTPUT 1 > OUTPUT VGA VGA RESOLUTION OUTPUT
S OUTPUT 2 > OUTPUT SVGA SVGA RESOLUTION OUTPUT
S OUTPUT 3 > OUTPUT XGA XGA RESOLUTION OUTPUT
S OUTPUT 4 > OUTPUT SXGA SXGA RESOLUTION OUTPUT
S OUTPUT 5 > OUTPUT UXGA UXGA RESOLUTION OUTPUT
S OUTPUT 6 > OUTPUT 480i 480i RESOLUTION OUTPUT
S OUTPUT 7 > OUTPUT 480P 480P RESOLUTION OUTPUT
S OUTPUT 8 > OUTPUT 720P 720P 60HZ RESOLUTION OUTPUT
S OUTPUT 9 > OUTPUT 1080i 1080i 60HZ RESOLUTION OUTPUT
S OUTPUT 10 >OUTPUT 1080P 1080P 60HZ RESOLUTION OUTPUT
S OUTPUT 11 > OUTPUT 576i 576i 60HZ RESOLUTION OUTPUT
S OUTPUT 12 > OUTPUT 576P 576P 60HZ RESOLUTION OUTPUT
S OUTPUT 13 > OUTPUT 720P 720P 50HZ RESOLUTION OUTPUT
S OUTPUT 14 > OUTPUT 1080i50 1080i 50HZ RESOLUTION OUTPUT
S OUTPUT 15 > OUTPUT 1080P50 1080P 50HZ RESOLUTION OUTPUT
S OUTPUT 16 > OUTPUT WXGA WXGA RESOLUTION OUTPUT
S OUTPUT 17 > OUTPUT WSXGA WSXGA RESOLUTION OUTPUT
S OUTPUT 18 > OUTPUT WUXGA WUXGA RESOLUTION OUTPUT
S SIZE 0 > SIZE FULL SCALER FULL OUTPUT
S SIZE 1 > SIZE OVERSCAN SCALER OVERSCAN OUTPUT
S SIZE 2 > SIZE UNDERSCAN SCALER UNDERSCAN OUTPUT
S SIZE 3 > SIZE LETTERBOX SCALER LETTERBOX OUTPUT
S SIZE 4 > SIZE PANSCAN SCALER PANSCAN OUTPUT

9www.atlona.com
Toll free: 1-877-536-3976
Local: 1-408-962-0515
Command Code Response Description
S PICTURE MODE 0-3 > PICTUREMODE STANDARD-
USER
0:STANDARD; 1 :MOVIE; 2:VIVID;
3:USER, PICTURE MODE OUTPUT
S CONTRAST 0-100 > CONTRAST 0-100 CONTRAST 0-100 ADJUST [Defaut:50]
S BRIGHTNESS 0-100 > BRIGHTNESS 0-100 BRIGHTNESS 0-100 ADJUST [Defaut:45]
S HUE 0-100 > HUE 0-100 HUE 0-100 ADJUST [Defaut:50]
S SATURATION 0-100 > SATURATION 0-100 SATURATION 0-100 ADJUST [Defaut:60]
S SHARPNESS 0-100 > SHARPNESS 0-100 SHARPNESS 0-100 ADJUST [Defaut:32]
S NR 0-3 > NR OFF-HIGH 0:OFF; l:LOW; 2:MIDDLE; 3:HIGH, NR CONTROL
S PCHPOSITION 0-100 > PCHPOSITION 0-100 H POSITION 0-100 ADJUST
S PCVPOSITION 0-100 > PCVPOSITION 0-100 V POSITION 0-100 ADJUST
S PCCLOCK 0-100 > PCCLOCK 0-100 PC MODE COLCK 0-100 ADJUST
S PCPHASE 0-63 > PCPHASE 0-63 PC MODE PHASE 0-63 ADJUST
S COLORTEMP 0-3 > COLORTEMP NORMAL-USER 0:NORMAL; 1:WARM; 2:COOL;
3:USER, COLOR TEMP SETTING
S RED 0-100 > RED 0-100 COLOR TEMP “RED” ADJUST [Defaut:47]
S GREEN 0-100 > GREEN 0-100 COLOR TEMP “GREEN” ADJUST [Defaut:47]
S BLUE 0-100 > BLUE 0-100 COLOR TEMP “BLUE” ADJUST [Defaut:47]
SOSDHPOSITION 0-100 > OSDHPOSITION 0-100 OSD H POSITION 0-100 ADJUST [Defaut:50]
S OSDVPOSITION 0-100 > OSDVPOSITION 0-100 OSD V POSITION 0-100 ADJUST [Defaut:50]
S OSDTIMEOUT 0-100 > OSDTIMEOUT 0-100 OSD TIMEOUT 0-100 SETTING [Defaut: 10]
S OSDBACKGROUND 0-8 > OSDBACKGROUND 0-8 OSD OSDBACKGROUND 0-8 ADJUST [Defaut:5]
S AUDIOMUTE 0-1 > AUDIOMUTE OFF-ON 0:OFF; 1 :ON, AUDIO MUTE CONTROL
S AUDIODELAY 0-3 > AUDIODELAY OFF-l 50MS 0:OFF; 1:40MS; 2:110MS; 3:150MS,
AUDIO DELAY SETTING
S RESET 1 > RESET ON RESET ACTION