Atmos D15p User manual

Instruction manual - GB

www.atmos.cz

Instruction

manual

www.atmos.cz

Instruction manual - GB

www.atmos.cz

GB-3

Contents

1. Intended use 5

2. Technical description 5

Control panel appearance 6

3. Technical data 7

Boiler drawings key 8

Technical data 8

Drawings of boilers 9

Extraction ventilator schematics – boiler types D20P, D30P, D40P and D50P 10

4. Supplied boiler accessories 11

Automatic ash removal from the boiler drum 11

5. Fuel 12

Basic wood burning data 12

Fuel heating capacity 13

6. Boiler bases 13

7. Environment type and boiler placement in a boiler room 13

8. Chimney 14

9. Flue-gas duct 14

10. Fire prevention during installation and use of heating appliances 15

11. Connecting boilers to the electric network 16

12. Electric wiring diagram for the boiler D15P without an extraction fan - model 2012 with a 6-pin connector 17

13.

Electric wiring diagram for the boilers D20P, D30P, D40P and D50P with an extraction fan - model 2012 with a

6-pin connector

14.

Electric wiring diagram for the boiler D15P without an extraction fan

with a 6-pin connector

and

module AD02 to control pump in boiler circuit from burner control unit AC07X (R) 18

15. Electric wiring diagram for the boilers D20P, D30P, D40P and D50P with an extraction fan, modele 2012 with 6-pin

connector and module AD02 - to control extraction fan of the boiler from burner control unit AC07X (R) 18

16. Wiring diagram connection of the boilers D20P, D30P, D40P and D50P with extraction fan, model 2012 with

6-pin connector and two modules AD02 - to control extraction fan of the boiler and pump in the boiler

circuit from burner control unit AC07X (R and R2) 19

17. Wiring diagram connection of the boilers D20P, D30P, D40P and D50Pwith extraction fan, model 2012 with

6-pin connector and module AD03 - to control extraction fan of the boiler and pump in the boiler circuit

from burner control unit AC07X (R and R2) 20

18. Obligatory ČSN EN standards related to boiler designing and installation 21

19. Choice and connection method of control and heating elements 21

20. Boiler corrosion protection 22

21. Prescribed boiler connection with an equalizing tank for burner control on the basis of TS and TV sensors 23

22. Prescribed boiler connection with an equalizing tank and with the ACD01 electronic control unit 23

23. Possible boiler connection with equalizing tank with DHW boiler and with solar system 24

24. Possible boiler connection with Laddomat 21/22 24

25. Laddomat 21/22 25

26. Thermoregulatory valve 25

27. Connection of overheat protecting cooling loop with a safety valve Honeywell TS 130 - 3/4 A or

WATTS STS20 26

28. Operating instructions 26

Preparing boilers for operation when burning pellets 26

Relation of waste gas temperatur to boiler (burner) output when burning pellets 28

29. Placing the shaped pieces into the combustion area 28

Connecting the burner A25 into boilers D15P and D20P 29

Connecting the burner A45 into boilers D30P, D40P and D50P 29

Boiler system with an external silo and conveyor of pellets 30

Boiler room with a large built-in pellet storage 31

Preparing boiler operation for emergency burning wood 32

Ignition and operation when burning alternative fuel - wood 32

Additional secondary air inlet placed under the doorframe 32

Mechanical output regulation – when burning alternative fuel (wood) 33

Draught regulator - HONEYWELL Braukmann FR124 – Assembly instructions 33

30. Fuel rell when burning alternative fuel (wood) 33

31. Boiler cleaning and ash removal 34

32. Heating system maintenance - including boilers 35

33. Use and inspections 35

34. Possible failures and troubleshooting 36

35. Spares 37

Door sealing cord replacement 38

Adjusting the door hinges and locks 38

36. Environmental protection 38

Disposal of the boiler after expiration of its service life 38

GUARANTEE CONDITIONS 39

BOILER INSTALLATION REPORT 40

ANNUAL INSPECTIONS RECORDS 41

RECORDS OF GUARANTEE PERIOD AND POST-GUARANTEE PERIOD REPAIRS

www.atmos.cz

4-GB

Instruction manual - GB

WE HOPE THAT YOU ARE SATISFIED WITH OUR

PRODUCT AND WE KINDLY RECOMMEND YOU TO

FOLLOW THESE MAIN RULES IMPORTANT FOR A

LONG SERVICE LIFE AND THE CORRECT FUNCTION-

ALITY OF THE BOILER

1. Installation, ignition test and operator‘s training shall be carried out by an installation company

trained by the manufacturer. This company also completes a boiler installation report (p.41).

2. When burning pellets use only good quality fuel of 6 – 8 cm diameter made from soft barkless

wood (white pellets).

3. Wood tar and condensates (acids) form in the fuel storage tank during the wood burning proc-

ess. Therefore, there must be a Laddomat 21/22 or a thermoregulatory valve installed behind the

boiler in order to keep the minimum temperature of water returning to the boiler at 65 °C.

Operating temperature of water in the boiler must be in the 80 - 90 °C range.

4. When the boiler operates in the wood-burning mode, it must not be permanently operated in an

output lower than 50 %.

5. Every circulating pump in the system must be regulated by an individual thermostat in order to

keep the specied minimum temperature of water returning to the boiler.

6. We recommend installing the boiler with at least one equalising tank; the volume of which

should be 500 – 1000 litres. Thus a longer service life of the pellet burner and lower fuel con-

sumption are achieved.

7. Use only dry rewood with 12 - 20 % moisture content – higher moisture content decreases

the boiler’s performance and increases consumption.

CAUTION – if the boiler is installed with a Laddomat 21/22 or with a TV 60 °C ther-

moregulatory valve and with the equalizing tank (see attached schematics), the guar-

antee period for the boiler drum is extended from 24 to 36 months. The guarantee

period for other parts remains unaffected. In non-compliance with these principles,

the drum’s and the heatproof shaped pieces’ service life may dramatically decrease due

to low-temperature corrosion. The boiler drum may corrode in as little time as 2 years.

CAUTION - INSTALLER SHOULD ALWAYS COMPLY WITH LOCAL PLANNING

AND BUILDING REQUIREMENTS.

Instruction manual - GB

www.atmos.cz

GB-5

1. Intended use

The hot water boilers ATMOS D15P, D20P, D30P, D40P and D50P are designed for convenient

heating in residential houses, weekend house and other similar buildings by wood pellets or re wood

(as an alternative fuel in case of urgent need). Pellets of 6 – 8 mm diameter and any dry rewood of

300 to 700 mm length (depending on the boiler type) may be used for heating. The boiler is not in-

tended for burning sawdust or small-particle wood waste.

2. Technical description

A pellet burner with a conveyor is tted to the left or right side of the boiler. It is attached to a

frame with sealing cord (18 x 32) by a screw. The boiler drum is manufactured as a welded structure

of 3 - 6 mm thick steel sheets. The boiler consists of a fuel-feeding hopper (combustion chamber)

which is in the lower and rear section tted with a heatproof shaped piece and in the upper part with

a ceramic spherical chamber (shaped piece). The boiler types D15P, D20P, D30P, D40P and D50P

have a heatproof shaped piece tted opposite the pellet burner. The shaped piece protects the boiler

drum against damage and also serves as a place on which the ame burns out completely. In the lower

part of the boiler, there is a movable grill (for facilitating the ash removal) under which an ash-pan is

located. A loading (cleaning) door is located in the front wall of the boiler. The boilers drum is ex-

ternally heat insulated by mineral wool placed beneath the sheet metal covers of the boilers’ external

housing. A panel with a main switch, operating (boiler) thermostat, pump thermostat, safety thermo-

stat, thermometer and fuse is located in the upper area of the boiler. The air inlet is equipped with a

air ap valve operated by the Honeywell FR124 draught regulator. The boiler standard model is tted

with a cooling loop protecting it against overheating. The models D20P, D30P, D40P and D50P have

also a suction ventilator tted to the rear side.The ventilator facilitates reaching the maximum output.

It is switched on and off by a switch located in the boiler control panel and it is controlled by the same

operating thermostat as the pellet burner.

With the D20P boiler type, use the extraction ventilator with the burner preset to an

output ranging from 16 – 22 kW only. With types D30P, D40P and D50P, the extraction

ventilator must be always operating when burning pellets.

www.atmos.cz

6-GB

Instruction manual - GB

Control panel appearance

Description:

1. Thermometer – monitors the temperature of water exiting the boiler

2. Main switch – allows for completely shutting down boiler if necessary (restart the pellet burner)

Control thermostat – regulates the operation of the pellet burner and also (with the D20P, D30P,

D40P, D50P models) regulates the extraction ventilator. The regulation is based on the temperature of

water exiting the boiler.

4. Pump thermostat – serves for switching the pump placed in the boiler circuit (set it to temperature be-

tween 70 – 80 °C).

5. Safety irreversible thermostat – serves as boiler protection against overheating in case of control ther-

mostat failure or as an indication of exceeding the emergency temperature. If such exceeding occurs, it

is then necessary to depress the thermostat.

7. Fuse (6.3 A)

- T6,3A/1500 - type H

pellet burner electronics protection.

8. Area for electronic regulation of the heating system can be used to house any type of regulation that

ts into an aperture of 92x138 mm. The electric harness is prefabricated and ready to be used for the

regulation’s power supply.

9. Automatic ash removal switch - it serves to switch on or off the ash removal when needed eg. in case

of cleaning the ash-pan. By switching off and then on you activate the ash removing module so that it

stops its sound signal and starts the automatic function of the ash removal.

10. Burner switch – it serves to switch on or off the burner

1. Thermometer

2. Main switch

3. Control thermostat (for boiler)

4. Pump thermostat

5. Safety thermostat

7. Fuse - T6,3A/1500 - type H

8. Area for electronic regulation of

the heating system (92x138 mm)

9. Automatic ash removal switch

10. Burner switch

ČERPADLO / PUMP

KOTLOVÝ / OPERATING

3 8 45 7 9

1 1

Instruction manual - GB

www.atmos.cz

GB-7

3. Technical data

ATMOS boiler type D15P D20P D30P

D40P

D50P

Boiler output kW 4,5 - 15 6,5 - 22 8,9 - 29,8

8,9 - 40

13,5 - 45

Heating surface m

1,9 2 2,7

2,7

3,6

Fuel shaft volume dm

70 70 105

105

140

Feeding hole dimensions mm 270x450 270x450 270x450

270x450

Specied chimney draught Pa 18 15 21

Max.operating water-pressure kPa 250 250 250

250

Boiler weight kg

305 315 386 386 455

Gas-outlet pipe diameter mm 150/152 150/152 150/152

150/152

Boiler height mm 1405 1405 1405

1405

Boiler width mm 606 606 606

606

Boiler depth mm 708 745 954

954

1154

Electric parts ingress protection IP 20

Electric input - at start-up

- in operation W

522

572

530

Boiler efciency % 90,4 91,1 92,4

91,0

91,1

Boiler class

5 5 5 5 5

Waste gas temperature at nominal out-

put (pellet type) °C 141 128 133

157

123

Waste gas combustion products ow

weight at nominal output – pellet type kg/s 0,012 0,016 0,025

0,031

0,035

Specied fuel Good quality pellets with 6 – 8 mm diameter, 5 - 25 mm lenght

and 16 - 19 MJ.kg

-1

caloric power (white pellets)

Alternative fuel in case of urgent need Dry rewood of 15 - 17 MJ.kg

-1

caloric power, 12 – 20 % moisture

content and 80 – 150 mm diameter

Average fuel (pellets) consumption at

nominal output kg.h

-1

3,7 5 8,6 9,4 10,6

Maximum wood length mm 310 310 510

510

710

Burning time at nominal output – wood

type hour 2 2 2

Boiler water volume l 65 82 91

117

Hydraulic pressure drop mbar 0,22 0,22 0,23

0,23

0,24

Equalising tank minimum volume l 500 500 750

750

1000

Connecting voltage V/Hz 230/50

Specied min. temperature of water returning to boiler is 65 °C when in operation.

Specied boiler operating temperature is 80 - 90 °C.

www.atmos.cz

8-GB

Instruction manual - GB

Boiler drawings key

Technical data

1. Boiler drum

2. Loading (cleaning) door

3. Ash-pan

4. Control panel

5. Air ap valve - only when burning wood

6. Heatproof shaped piece – combustion area

bottom

7. Heatproof shaped piece – upper spherical

chamber

8. Frame screen

9. Extraction ventilator

10. Output regulator - Honeywell FR 124

11. Door lling - Sibral

12. Door sealing 18 x 18 mm

13. Lock - handle

14. Heatproof shaped piece – rear face of the

spherical chamber

15. Ash-pan lock - nut

16. Cooling loop

17. Burner aperture lid

18. Tube heat exchanger cleaning lid

19. Waste gas brake (for type D20P - 3x brush,

for type D30P, D40P and D50P -1x brush +

1x iron)

20. Rear-duct cleaning lid

21. Thermometer

22. Main switch

23. Control (boiler) thermostat

24. Pump thermostat

25. Safety thermostat

26. Fuse T6,3A/1500 - type H

28. Grill

29. Doubleswitch of the automatic ash removal

and burner

K – the ue-gas duct neck

L – the boiler water outlet

M – the boiler water inlet

N – lling valve pipe sleeve

P – sleeve for a sensor of the valve which reg

lates the cooling loop (TS 131, STS 20)

Dimensions

D15P D20P D30P D40P D50P

A1405 1405 1405 1405 1405

B 708 754 954 954 1154

C606 606 606 606 606

D 1040 848 848 848 848

E150/152 150/152 150/152 150/152 150/152

G211 211 211 211 211

H1163 1163 1163 1163 1163

CH 202 202 202 202 202

J6/4” 6/4” 6/4” 6/4” 6/4”

Instruction manual - GB

www.atmos.cz

GB-9

Drawings of boilers

Cut away views - type D15P

Cut away vies – types D20P, D30P, D40P, D50P

www.atmos.cz

10-GB

Instruction manual - GB

Cut away view - type D15P Cut away view – type D50P

Boiler without an extraction ventilator Boiler with an extraction ventilator

Extraction ventilator schematics – boiler types D20P, D30P, D40P, D50P

CAUTION – The extraction ventilator is supplied disassembled. Place it over the rear ue-

gas duct, tighten everything well, connect into a socket and test for its smooth operation.

1 - Motor

2 - Plate

3 - Rotating wheel (stainless steel)

4 - Nut with left-handed thread and washer

5 - Wing nut

6 - Bolt

7 - Large gasket (2pcs)

8 - Small gasket

Boilers D30P, D40P, D50P are supplied with impeller

of diameter 150mm. The impeller is to be exchanged

by plumber (never by customer) instead the existing impeller in case of installing the boiler

in chimney with a very high draught which is not able to reduce by any possible way. The

impeller is installed so that it was easier to adjust optimally the burner.

Instruction manual - GB

www.atmos.cz

GB-11

4. Supplied boiler accessories

Steel brush with accessories 1pc

Poker - for boiler body cleaning 1pc

Cleaning re hook - for cleaning burning chamber of the burner 1pc

Filling-in valve 1pc

Operating and maintenance instructions manual 1pc

Draught regulator - Honeywell FR 124 1pc

Automatic ash removal from the boiler drum

Each pellet type boiler produced after 1.3. 2007 can be tted

with automatic ash removal from the boiler body into the ad-

ditional ash-pan, which will require emptying once in 3 to 45

days, depending on the quality of the pellets. For one minute,

this automatic device removes the ash from the chamber under

the burner by means of screw conveyor in regular interval of

one hour (twelve hour) or according another setting in the ash

removal module. We can reset or repeat this cycle in the boiler

several times by switching the switch /29 (10)/ on and off. When

the additional ash-pan is completely full, the ash removal device

will stand off (a screw) and a sound signal will start. New start

up should be performed after cleaning the external ash-pan by

means of switching the switch /29 (10)/ on and off for 5 - 10

second (the B variation we do not make with a main switch).

The automatic ash-removal system does not need any specic operating procedures. Just

make sure that the additional ash-pan /30/ is emptied regularly. The con tainer is tted to

the boiler by means of two clips with safety catches /32/. These clips must be fastened well

during the boiler operation so that no inadvertent release of the ash-removal device and

consequent transfer of ash into the boiler room may occur. This device must be installed in

compliance with the supplied installation instructions. When installing the device, we follow

the installation manual delivered with the device. In case of wood burning put back the mov-

ing grate so that the wood do not fall into the ash-pan.

www.atmos.cz

12-GB

Instruction manual - GB

5. Fuel

The specied fuel are good quality pellets of 6 - 8 mm diameter, 5 - 25 mm length and 16 - 19

MJ.kg-1 caloric power. As alternative fuel (in case of urgent need) use dry rewood of 80 – 150 mm

diameter, minimum 2 years old with 12 – 20% moisture content, 300 – 700mm length - depend on

boiler type and 16 - 19 MJ.kg-1 caloric power. Good quality pellets are such that do not disintegrate

into sawdust and are made from soft barkless wood without other additive (so called white pellets).

Basic wood burning data

You can ensure maximum output and a long service life if you burn wood which has been left for

at least 2 years to dry. The following graph illustrates the relationship of moisture content to heating

capacity of the fuel. The energy content declines dramatically with increased water contents.

Example:

Wood with 20% moisture contents has thermal power of 4 kWh /1 kg of wood.

Wood with 60% moisture contents has thermal power of 1.5 kWh /1 kg of wood.

•e.g. – spruce wood which has been stored

for 1 year under shelter – see graph

Boilers are not suitable for burning wood with moisture content lower than 12%.

High-quality wooden pellets – white without

black dots (bark)

Poor-quality wooden pellets – dark with bark

(with black dots)

Instruction manual - GB

www.atmos.cz

GB-13

Fuel heating capacity

Wood - type Heating capacity per 1 kg

kcal kJoule kWh

Spruce 3900 16250 4,5

Pine 3800 15800 4,4

Birch 3750 15500 4,3

Oak 3600 15100 4,2

Beech 3450 14400 4,0

Raw wood does not burn easily, produces a lot of smoke and substantially decreases

the service life of your boiler and chimney. Boiler output drops as low as 50% and fuel

consumption doubles.

6. Boiler bases

Boiler type (mm) A B

D15P, D20P 600 600

D30P, D40P 600 800

D50P 600 1000

7. Environment type and boiler placement in a boiler room

Boilers may be used in a “basic environment” - AA5/AB5 as specied in Czech standard

ČSN3320001. Boilers must be placed in a boiler room with sufcient air access necessary for com-

bustion. Placing boilers in living areas (in-

cluding halls/corridors) is not permitted.

The combustion air inlet aperture in the

boiler room must be of minimum 350 cm2

for boilers of 15 - 45 kW outputs.

1- Chimney

2- Flue duct

3- Boiler

4- Burner

5- Conveyor

6- Container

We recommend providing a concrete

(metal) base under the boiler.

www.atmos.cz

14-GB

Instruction manual - GB

8. Chimney

Connecting the appliance to the chimney vent stack must always be carried out with the per-

mission of the appropriate chimney authority. The vent stack must always be capable of providing

sufcient draught and it must discharge the waste gas into the open atmosphere in a reliable manner

for all possible operating conditions. The dimensions of the individual vent stack must be correct to

ensure good functionality of the boiler; because the draught inuences combustion, performance

and the service life of the boiler. The chimney draught is directly dependent on its cross section,

height and the inner wall ruggedness. It is not permitted to connect another appliance into a chimney

into which a boiler is connected. The chimney diameter must not be smaller than the boiler outlet

(min. 150 mm). The chimney draught must comply with the specied values (see technical data, page

7). The chimney must not be excessively high, otherwise the boiler effectiveness is decreased and the

combustion is affected (the ame “breaks”). In case of excessive draught, install a throttle valve in the

ue gas duct between the boiler and the chimney.

Indicative values of the chimney cross-section dimensions:

20 x 20 cm height 7 m

20-cm diameter height 8 m

15 x 15 cm height 11 m

16-cm diameter height 12 m

Exact chimney dimensions are stipulated in Czech standard ČSN 73 4201.

Specied chimney draught is stated in section 3 „Technical Data“.

9. Flue-gas duct

The ue-gas duct must be connected into the chimney vent stack. If the boiler cannot be connected

to the chimney directly, the appropriate ue-gas duct extension must be as short as possible in the given

circumstances, but not longer than 1m, it must be without additional heating surface and must incline

upwards in the direction towards the chimney. Flue-gas ducts must be mechanically durable and

sealed against combustion products and gas penetration, and it must be possible to clean them inside.

The ue-gas ducts must not be lead through another person‘s apartment or property. The internal diam-

eter of the ue-gas duct must not be larger than the internal di-

ameter of the chimney intake and it must not decrease in width

in the direction towards the chimney. Use of elbow-pipes is not

suitable. Methods for providing ue-gas duct entries through

ammable material structures are stipulated in appendices 2

and 3 of the Czech standard ČSN 061008. These are appropri-

ate for mobile installations, wooden cottages etc.

1- Waste gas thermometer

2- Cleaning aperture

3- Throttle valve (draught limiter)

INFO - In case of excessive chimney draught, in-

stall a throttle valve /3/ or draught limiter.

Boiler

Chimney

Instruction manual - GB

www.atmos.cz

GB-15

10. Fire prevention during installation and use of heating appliances

Selected from ČSN 061008 – Fire safety of local appliances and heat sources.

Safe distances

When installing the appliance, keep a minimum safe distance of 200 mm from building materials.

This distance is valid for boilers and ue-gas ducts positioned near ammable materials of the B, C1

and C2 ammability class (the ammability classes are listed in chart 1). It is necessary to double the

200 mm safe distance if the boilers and ue-gas ducts are placed near ammable materials of C3 class

(see chart 1). It is also necessary to double the safe distance if the ammability class of the material

in question cannot be determined. The safe distance can be decreased to one half (to 100 mm) if a

heat insulating, non-combustible screen (asbestos board) of a 5 mm minimum thickness, is placed 25

mm from the protected combustible material (so called ammable insulation). The screening board

or protection screen (on the protected object) must exceed the boiler outline including its ue-gas duct

on each side by at least 150 mm and by at least 300 mm above its upper surface. The screening board

or protection screen must be also used for all xtures and ttings from combustible materials in cases

where the safe distance cannot be maintained (such as in mobile structures or wooden cottages etc. -

for more details see ČSN 061008 standard). The safe distance must be maintained even when placing

xtures and ttings near the boilers.

If boilers are placed on oors from combustible materials, the oor must be tted with a non-

combustible, heat insulating pad exceeding the boiler’s ground-outline on the side where the stoking

and ash-pan apertures are, by at least 300 mm (in front of the aperture) and on all the other sides by

at least 100 mm. The non-combustible, heat-insulating pad can be made from any material of A am-

mability class.

Chart 1

Flammability classes of build-

ing materials and products

A – non-combustible granite, sandstone, concrete, bricks, ceramic tiles, mortars, reproof-

ing plasters etc.)

B – non-easily ammable Akumin, Izomin, Heraklit, Lignos, basalt felt boards, breglass

boards, Novodur

C1 – low degree of ammabil-

ity

deciduous tree wood (oak, beech), Hobrex boards, plywood, Sirkolit,

Werzalit, hardened paper (Formica, Ecrona)

C2 – medium degree of am-

mability

coniferous tree wood (pine tree, larch, spruce), chipboards and cork

boards, rubber ooring (Industrial, Super)

C3 – high degree of amma-

bility

breboards (Hobra, Sololak, Sololit), cellulose materials, poly-

urethane, polystyrene, polyethylene, foamed PVC

CAUTION - In circumstances when there is a risk of temporary access of ammable gases

or fumes, or during works when a temporary re or explosion risk may possibly occur (such

as gluing linoleum, PVC etc.) the boilers must be put out of operation long enough before

the risk occurrence. No items from ammable materials may be placed on the boilers or

near them into a distance lower than the specied safe distance (more ČSN EN 13501-1).

In short, do not put any items that could easily catch re in the vicinity of the boiler.

www.atmos.cz

16-GB

Instruction manual - GB

11. Connecting boilers to the electric network

The boilers are connected to 230 V, 50 Hz mains with a mains cable without a plug. The mains

supply cable in case of repair it must be replaced with the same type by the servicing organization.

Connection, maintenance and reparation can be made only by a qualied person in accordance with

valid regulations of the particular country.

CAUTION - The mains cable must not be equipped with a plug (designed to be connected

to a socket). It must be connected in a xed way to a switch board or junction box to avoid

confusion of the conductors.

Mains cable must be regularly checked and maintained in the prescribed condition. It is forbidden to

interfere in to the safety circuits and elements for safe and reliable operation of the boiler. If any dam-

age of electrical equipment must be the boiler out of operation, disconnect from the mains and ensure

a qualied repair according to applicable standards and regulations.

After the installation of the burner on the boiler the technician must connect the burner and subsequently

the entire boiler to the electric mains in accordance with the attached wiring diagram (page 17 - 21).

Electric conection of the burner:

Between the burner and boiler a six-wire cable is use that is connected with one end to the burner

with a 6-pin connector (part of the burner) and the other end 6-pin connector (part of the boiler - pla-

ced in the side hood) to the boiler. The boiler is also equipped with a 3-pin connector for connection

of pump in boiler circuit and with a 3-pin connector (with jumper) for easy connection and controling

of the burner from external regulator.

Connectors in the right side hood:

1- connector for power cord - black (L - brown, N - blue, PE - green/yellow)

2- connector for pump in boiler circuit - white (L - brown, N - blue, PE - green/yellow)

3- connector for external regulator of the boiler (with jumper)

4- connector for burner ATMOS connection model AC07X - (L1, L2, R, R2,N, PE)

5 - connector for extraction fan (except D15P)

At the bottom part of the side hood is red connector blinded with black cap. Standard designed to

engage the automatic ash removal (or other applications) - not connected to the terminal.

Connector in the left side hoodConnectors in the right side hood

- 5

1 -

2 -

3 -

4 -

Instruction manual - GB

www.atmos.cz

GB-17

12. Electric wiring diagram for the boiler D15P without an ex-

traction fan - model 2012 with a 6-pin connector

13. Electric wiring diagram for the boilers D20P, D30P, D40P,

D50P with an extraction fan - model 2012 with a 6-pin con-

nector

1 2 3 4 5 6 7 8 9 10 11 12

L N PE L

M M

LN PE

130101_D2045P_A2545_6P

poj-Cpoj-1

FUSE 6,3 A

SICHERUNG 6,3 A

POJISTKA 6,3 A

HLvyp

SNvyp

HNvyp

SLvyp

1245

SWITCH

SCHALTER

HL.VYPÍNAČ















t °C

TČ-C

TČ-2

TČ-1

PUMP THERMOSTAT

PUMPETERMOSTAT

TERMOSTAT NA ČERPADLO

t °C

PT-1

PT-C

OPERATING THERMOSTAT

BETRIEB TERMOSTAT

PROVOZNÍ TERMOSTAT

230V/50Hz

 



REGN (X6:3)

REGL (X6:4)

REGPE (X6:2)

L2OUT (X7:7)









































































LPUMP (X7:5)

WHEN USE ELECTRONIC REGULATION ACD01 AND PELLETBURNER A2545 MUST BE THESE CHANGES OF WIRING:

BEI DER STEUERUNG DES KESSELBETRIEBES DER ELEKTRONISCHE REGELUNG ACD01 UND PELLETBRENNER A2545 MÜSSEN DIESE ÄNDERUNGEN MACHEN SEIN:

PŘI ZAPOJENÍ ELEKTRONICKÉ REGULACE ACD01 A PELETOVÉHO HOŘÁKU A2545 PROVEĎTE TYTO ZMĚNY:









BLBLACKSCHWARZČERNÁ BRBROWNBRÄUNEHNĚDÁ

BUBLUEBLAUMODRÁ REREDROTČERVENÁ

GYGREEN/YELLOWGRÜN/GELBZELENO/ŽLUTÁ WWHITEWEISBÍLÁ

GRGREYGRAUŠEDÁ

OPTION OF ACCES POINT FOR BOILER ACCESSORIES

ANLAGERUNGALTERNATIVE FÜR KESSELZUBEHÖR

ALTERNATIVA PŘIPOJENÍ PŘÍSLUŠENSTVÍ KOTLE

ASHREMOVER

ENTASCHUNG

ODPOPELNĚNÍ

 









RESERVOIR POINT "L2 OUT" OF BURNER AND FAN TO THE ELECTRONIC REGULATION (ACD01)

SPEISEKLEMME "L2 OUT" DER BRENNER UND VENTILATOR FÜR DIE ELEKTRONISCHE REGELUNG (ACD01)

PŘIPOJOVACÍ SVORKA "L2 OUT" HOŘÁKU A VENTILÁTORU DO ELEKTRONICKÉ REGULACE (ACD01)

WHEN ELECTRONIC REGULATION CONTROL BURNER  CONNECTORS "PTC" AND "PT1" MUST BE UNCONNECT

DEN KONNEKTOREN "PTC" UND "PT1" ABKLEMMEN BEI DER BRENNERBEDIENUNG DER ELEKTRONISCHE REGELUNG

KONEKTORY "PTC" A "PT1" ODPOJIT PŘI OVLÁDÁNÍ HOŘÁKU ELEKTRONICKOU REGULACÍ

RESERVOIR POINT "L PUMP" OF BOILER PUMP TO THE ELECTRONIC REGULATION (ACD01)

SPEISEKLEMME "L PUMP" DER KESSELPUMPE FÜR DIE ELEKTRONISCHE REGELUNG (ACD01)

PŘIPOJOVACÍ SVORKA "L PUMP" KOTLOVÉHO ČERPADLA DO ELEKTRONICKÉ REGULACE (ADC01)

WHEN ELECTRONIC REGULATION CONTROL BOILER PUMP  CONNECTORS "TČC" AND "TČ2" MUST BE UNCONNECT

DEN KONNEKTOREN "TČC" UND "TČ2" ABKLEMMEN BEI DER KESSELPUMPESEBEDIENUNG DER ELEKTRONISCHE REGELUNG

KONEKTORY "TČC" A "TČ2" ODPOJIT PŘI OVLÁDÁNÍ KOTLOVÉHO ČERPADLA ELEKTRONICKOU REGULACÍ

ACCES POINT FOR EXTERNAL BOILERREGULATION  PLUG IN CONNEKTOR

ANLAGERUNG FÜR EXTERN KESSELREGELUNG  KLEMME IN DEN KONEKTOR

PŘIPOJOVACÍ SVORKY PRO EXTERNÍ REGULACI KOTLE  KLEMA V KONEKTORU

ACCES POINTS  FOR EXAMPLE FOR MODUL AD01  TIMEUNIT OF ASHREMOVER

SPEISEKLEMME  ZUM BEISPEILE FÜR MODUL AD01  ZEITBEDIENUNG FÜR DEN ENTASCHUNG

PŘIPOJENÍ  NAPŘÍKLAD PRO MODUL AD01  ČASOVÝ MODUL ODPOPELNĚNÍ

VARIANTS OF RESERVOIR POINTS "REG L,N,PE" (FERRULE/FASTON 6,3) FOR ELECTRONIC REGULATION

SPEISEKLEMMEVARIANTEN "REG L,N,PE" (ADERENDHÜLSE/FASTON 6,3) FÜR ELEKTRONISCHE REGELUNG

VARIANTY NAPÁJECÍCH SVOREK "REG L,N,PE" (DUTINKA/FASTON 6,3) PRO ELEKTRONICKOU REGULACI

CONNECTOR (BLACK/RED)  FOR EXAMPLE RESERVOIS POINT FOR MODUL AD01  MOTOR OF ASHREMOVER

KONNEKTOR (SCHWARZ/ROT)  ZUM BEISPIEL FÜR DEN MODUL AD01  ENTASCHUNGMOTOR

KONEKTOR (ČERNO ČERVENÝ)  NAPŘÍKLAD PRO MODUL AD01  MOTOR ODPOPELNĚNÍ

vyp2-1

vyp2-4

vyp2-2

vyp2-5

12 45

VYPÍNAČ VYPÍNAČ

HOŘÁKU ODPOPELNĚNÍ

SCHALTER FÜR SCHALTER FÜR

BRENER ENTASCHUNG

BURNER ASHREMOVER

SWITCH SWITCH

t °C

BT-L2

BT-L1

SAFETY THERMOSTAT

SICHERHEITSTERMOSTAT

BEZPEČNOSTNÍ TERMOSTAT

BT-N1

BT-N2

 



  





R2 A25-45 6PIN

KONEKTOR

   



AD01

KONDENZATOR 1 F

1 2 3 4 5 6 7 8 9 10 11 12

L N PE L

M M

LN PE

130101_D1425P_A2545_6P

poj-Cpoj-1

FUSE 6,3 A

SICHERUNG 6,3 A

POJISTKA 6,3 A

HLv yp

SNv yp

HNvyp

SLvyp

1245

SWITCH

SCHALTER

HL.VYPÍNAČ













  

t °C

TČ-C

TČ-2

TČ-1

PUMP THERMOSTAT

PUMPETERMOSTAT

TERMOSTAT NA ČERPADLO

t °C

PT-1

PT-C

OPERATING THERMOSTAT

BETRIEB TERMOSTAT

PROVOZNÍ TERMOSTAT

230V/50Hz

 





REGN (X6:3)

REGL (X6:4)

REGPE (X6:2)

L2OUT (X7:7)









































































LPUMP (X7:5)

WHEN USE ELECTRONIC REGULATION ACD01 AND PELLETBURNER A2545 MUST BE THESE CHANGES OF WIRING:

BEI DER STEUERUNG DES KESSELBETRIEBES DER ELEKTRONISCHE REGELUNG ACD01 UND PELLETBRENNER A2545 MÜSSEN DIESE ÄNDERUNGEN MACHEN SEIN:

PŘI ZAPOJENÍ ELEKTRONICKÉ REGULACE ACD01 A PELETOVÉHO HOŘÁKU A2545 PROVEĎTE TYTO ZMĚNY:

t °C

BT-L2

BT-L1

SAFETY THERMOSTAT

SICHERHEITSTERMOSTAT

BEZPEČNOSTNÍ TERMOSTAT

BT-N1

BT-N2









BLBLACKSCHWARZČERNÁ BRBROWNBRÄUNEHNĚDÁ

BUBLUEBLAUMODRÁ REREDROTČERVENÁ

GYGREEN/YELLOWGRÜN/GELBZELENO/ŽLUTÁ WWHITEWEISBÍLÁ

GRGREYGRAUŠEDÁ

OPTION OF ACCES POINT FOR BOILER ACCESSORIES

ANLAGERUNGALTERNATIVE FÜR KESSELZUBEHÖR

ALTERNATIVA PŘIPOJENÍ PŘÍSLUŠENSTVÍ KOTLE

ASHREMOVER

ENTASCHUNG

ODPOPELNĚNÍ

 









RESERVOIR POINT "L2 OUT" OF BURNER AND FAN TO THE ELECTRONIC REGULATION (ACD01)

SPEISEKLEMME "L2 OUT" DER BRENNER UND VENTILATOR FÜR DIE ELEKTRONISCHE REGELUNG (ACD01)

PŘIPOJOVACÍ SVORKA "L2 OUT" HOŘÁKU A VENTILÁTORU DO ELEKTRONICKÉ REGULACE (ACD01)

WHEN ELECTRONIC REGULATION CONTROL BURNER  CONNECTOR "PTC" MUST BE UNCONNECT

DEN KONNEKTOR "PTC" ABKLEMMEN BEI DER BRENNERBEDIENUNG DER ELEKTRONISCHE REGELUNG

KONEKTOR "PTC" ODPOJIT PŘI OVLÁDÁNÍ HOŘÁKU ELEKTRONICKOU REGULACÍ

RESERVOIR POINT "L PUMP" OF BOILER PUMP TO THE ELECTRONIC REGULATION (ACD01)

SPEISEKLEMME "L PUMP" DER KESSELPUMPE FÜR DIE ELEKTRONISCHE REGELUNG (ACD01)

PŘIPOJOVACÍ SVORKA "L PUMP" KOTLOVÉHO ČERPADLA DO ELEKTRONICKÉ REGULACE (ADC01)

WHEN ELECTRONIC REGULATION CONTROL BOILER PUMP  CONNECTOR "TČ2" MUST BE UNCONNECT

DEN KONNEKTOR "TČ2" ABKLEMMEN BEI DER KESSELPUMPESEBEDIENUNG DER ELEKTRONISCHE REGELUNG

KONEKTOR "TČ2" ODPOJIT PŘI OVLÁDÁNÍ KOTLOVÉHO ČERPADLA ELEKTRONICKOU REGULACÍ