Atop Ablelink sg6001 User manual

Atop ABLELink®GPRS Serial Server

SG6001 User Manual

Version 1.0

Updated on 2004/09/03

Tel: 886-3-5508137

Fax: 886-3-5508131

www.atop.com.tw

User manual Version 1.0

ABLELink®GPRS Serial Server SG6001

IMPORTANT ANNOUNCEMENT

The information contained in this document is the property of Atop Technologies, Inc.

and is supplied for the sole purpose of the operation and maintenance of products of

Atop Technologies, Inc. No part of this publication is to be used for any other purposes,

and it is not to be reproduced, copied, disclosed, transmitted, stored in a retrieval

system, or translated into any human or computer language, in any form, by any means,

in whole or in part, without the prior express written consent of Atop Technologies, Inc.

Publish by

Atop Technologies, Inc.

2F, No. 146, Sec. 1, Tung-Hsing Rd.

Jubei City, Hsinchu 302

Taiwan, R.O.C.

Tel: 886-3-5508137

Fax: 886-3-5508131

www.atop.com.tw

All other product names referenced herein are registered trademarks of their respective

companies.

2/71

User manual Version 1.0

ABLELink®GPRS Serial Server SG6001

FCC Statement

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation.

This equipment generates and can radiate radio frequency energy and, if not installed

and used according to the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which is found by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

--Reorient or relocate the receiving antenna

--Increase the separation between the equipment and device

--Connect the equipment to an outlet other than the receiver

--Consult a dealer or an experienced radio/TV technician for assistance

CE Mark Warning

In a domestic environment, this product may cause radio interference, in which case the

user may be required to take adequate measures.

SG6001 Safety Instructions

To avoid damage and possible danger, SG6001 should not be placed at the

humid environment with high temperature. For more information, please refer to

the descriptions in the specifications.

Please note that SG6001 GPRS Serial Server can be referred to as SG6001 or simply

as SG6001 through the whole manual. Moreover, please note that SG6001 may be

considered a GPRS Data Terminal (GDT) when talking about the complete GPRS

architecture. If it is the case, SG6001 may be referred to as GDT.

3/71

User manual Version 1.0

ABLELink®GPRS Serial Server SG6001

Contents

1. OVERVIEW ............................................................................................................................................................6

1.1 Introduction ..........................................................................................................6

1.2 Features...............................................................................................................8

1.3 Benefits ................................................................................................................8

1.4 Specifications .......................................................................................................9

1.5 Package List ......................................................................................................10

1.6 Panel..................................................................................................................10

2.HARDWARE INSTALLATION ..........................................................................................................................11

2.1 SIM Card Installation.......................................................................................... 11

2.2 SIM Card Check.................................................................................................12

2.3 Device Attachment .............................................................................................13

2.4 Power Supply Installation...................................................................................13

2.5 LED Status Indication.........................................................................................14

3. SOFTWARE INSTALLATION ......................................................................................................................... 15

3.1 Overview ............................................................................................................15

3.1.1 GGS ..........................................................................................................16

3.1.2 ADM ..........................................................................................................16

3.1.3 API Utility...................................................................................................16

3.1.4 Console Utility ...........................................................................................16

3.2 GGS (GPRS Gateway Software) Installation .....................................................16

3.3 ADM (Administration Manager) Installation ........................................................21

3.4 API Utility Installation..........................................................................................25

3.5 Console Utility Installation ..................................................................................25

4.CONFIGURATIONS ........................................................................................................................................... 30

4.1 Local Configuration ............................................................................................30

4.1.1 To Run Console Utility...............................................................................30

4.1.2. To Configure Console Utility.....................................................................30

4.2 Remote Configuration ........................................................................................34

4.2.1 GGS Configuration....................................................................................34

4/71

User manual Version 1.0

ABLELink®GPRS Serial Server SG6001

4.2.1.1 To Run GGS.....................................................................................34

4.2.1.2 To Configure GGS ............................................................................35

4.2.2 ADM Configuration ....................................................................................39

4.2.2.1. To Run ADM ....................................................................................39

4.2.2.2. To Configure GDT Group ................................................................40

5.TROUBLESHOOTING ...................................................................................................................................... 70

APPENDIX A: GPRS LED STATUS INDICATION DESCRIPTION ............................................................ 71

A.1 Non-Console Mode:...........................................................................................71

A.2 Console Mode: ..................................................................................................71

5/71

1. Overview

1.1 Introduction

The GSM/GPRS wireless network combines the world’s leading wireless standard—the

Global System for Mobile Communications (GSM)—with fast, packet-switched access to

data networks such as the Internet. Providing this fast access is the General Packet

Radio Service (GPRS).

SG6001 is designed to operate in GSM/GPRS networks. Two data services are

available in the GSM/GPRS networks: GPRS, a packet switched connection, and SMS,

a short message service.

GPRS

GPRS is an IP-based service that offers fast, packet-switched access to data networks

such as the Internet. It is a mobile service that improves the peak-time capacity of a

GSM network. GPRS gives packet-switched access over GSM to external data

networks with high peak transfer capacity. The main objective of GPRS is to offer

access to standard data networks such as TCP/IP. GPRS is a non-voice service

designed specifically for transmitting data. It breaks data messages into separate

packets for transmission from the mobile device and sends them to destinations in an

external network.

Most Internet-based application or service will run on GPRS. GPRS offers peak

throughputs of 40 Kbps (53.6 Kbps raw) because GPRS capacity is shared among

active users in the same coverage area, actual throughputs may vary.

SG6001 GPRS Serial Server

SG6001 GPRS Serial Server is a stand-alone device, enabling various kinds of legacy

devices with simple I/O and proprietary serial protocols to communicate over

GSM/GPRS network and the Internet easily and freely.

In addition to the standard GSM/GPRS modem functionality; SG6001 is supplied with

easy-to-use APIs and GPRS Gateway Software that streamline application development

process, freeing system integrators from dealing with complex communication protocols

of GPRS and the Internet.

6/ 71

User manual Version 1.0

ABLELink®GPRS Serial Server SG6001

With versatile I/O and flexible RF modules selections, SG6001 can be easily connected

to a wide range of RS-232/422/485 equipments, making it an ideal solution for

automation, M2M (Machine-to-Machine), environmental monitoring and remote device

management. SG6001 also includes Management Software that can be used to

remotely configure, monitor, and troubleshoot the attached device.

The following picture illustrates the basic architecture of SG6001 and the related

products.

7 / 71

User manual Version 1.0

ABLELink®GPRS Serial Server SG6001

1.2 Features

◆ GSM/GPRS modem with built-in TCP/IP stack

◆ Supports selectable RS-232/422/485 interface

◆ Built-in Watch-dog

◆ Wall-Mount, DIN-Rail design

◆ Industrial design with surge protection and optical isolation

◆ Provides GPRS Link Management

◆ Initiate GPRS Link automatically

◆ Resolve dynamic IP

◆ Automatic GPRS Connection Monitor

◆ SDK-Free with APIs and GPRS Gateway Software

◆ Built-in TCP/IP stacks

◆ Local or Remote Firmware Upgrade Over The Air (OTA)

◆ Easy update system and radio parameters OTA through an Internet-based GUI software

1.3 Benefits

◆ Connect any serial devices to GPRS and the Internet

◆ Plug-and-Play design with easy-to-use APIs for easy integration

◆ No need to build expensive fixed line network, saving cost substantially

◆ Easily manage and control distributed remote devices

◆ Reliable GPRS network connectivity, providing fast and cost-effective long-range wireless

communication

8 / 71

User manual Version 1.0

ABLELink®GPRS Serial Server SG6001

1.4 Specifications

Functional Specifications Power

Processor Environment 9-45 VDC Input Voltage

Low power-consumption CPU Power consumption:

128KB SRAM <1.4W (GPRS on line)

GPRS Connectivity 2W (searching for GPRS)

GPRS multi-slot Class 8 <360mW (Idle)

GPRS mobile station Class 8 Environment

Max. 85.6 kbps (download) Operating: -20℃〜70℃

Max. 21.4 kbps (uplink) Storage: -30℃〜80℃

Coding Schemes: CS1, CS2, CS3, CS4 Humidity: 5-85% RH

PPP-Stack Mechanical Specifications

Serial Connectivity SIM Card holder (3V/5V)

Single port 1200 〜230Kbps DB9 connector

Signal: Terminal block

RS-232 DB9 cable: TxD, RxD, RTS,

CTS, DTR, DSR, DCD, GND

Status LED indicator (RUN/COM/GPRS)

RS-232 Terminal block: TxD, RxD,

RTS, CTS, GND

SMA F external antenna connector

RS-422 4 Wire: TxD+, TxD-, RxD+,

RxD-, GND

Wall-mount, DIN-Rail design

RS-485 2: Wire Data+, Data-, GND Dimensions: 125x117x46 (mm)

Parity: None, Even, Odd, mark, Space Case Material: SECC sheet Metal (1mm)

Package Contents

Flow Control: Hardware CTS, RTS or Software

Xon/Xoff

Data Bits: 7 or 8

Stop Bits: 1 or 2

Integrated Protocols

TCP, UDP, ICMP, PPP

Regulatory Approvals

CE, FCC

SG6001 GPRS Serial Server

GPRS Antenna

Power Supply Adaptor

GPRS Gateway Software, API, and

Console Utility

Windows-based Administration Utility

User’s Manual

9 / 71

User manual Version 1.0

ABLELink®GPRS Serial Server SG6001

1.5 Package List

Before getting started, please make sure that you have the following devices and

accessories. If you find any items lost or damaged, please contact your distributor or

retailer for support and assistance.

1. SG6001 GPRS Serial Server x 1

2. Power adaptor x 1

3. Bracket x 1

4. CD-ROM disk containing drivers and user manual x 1

5. Atop GPRS Serial Server Quick Start Guide x 1

1.6 Panel

1. Antenna is where SG6001 receives and sends data through GSM/GPRS.

2. Serial port with DB9 connector allows connecting SG6001 with other device.

3. DIP switch allows switching between RS-232/Console/RS-485/RS-422.

Please refer to the table beside the switch for detailed information.

4. Another serial port with terminal block allows connecting SG6001 with other device.

5. LED status indicator displays the status of SG6001.

6. Power button is where you push on/push off SG6001

7. Power slot offers power supply via other power source.

8. DC IN jack is where you connect power supply adaptor.

10 / 71

User manual Version 1.0

ABLELink®GPRS Serial Server SG6001

2.Hardware Installation

2.1 SIM Card Installation

a. Push the yellow button to take out the SIM card tray at the upper side of SG6001.

b. Insert SIM card into the SIM card tray. Please make sure that you place the SIM

card at the right position; otherwise, it may damage your SIM card, or it may not

work at all.

c. Push the SIM card tray into the slot. The installation is complete.

11 / 71

User manual Version 1.0

ABLELink®GPRS Serial Server SG6001

2.2 SIM Card Check

You may check if SIM card is ready in SG6001 by two methods. Read the LED status

indicator in LED Status Indication part, or use any terminal program, such as Hyper

Terminal, to check SIM card status. The following is the default settings when using

Hyper Terminal:

Item Value

Baud rate 9600 bps

Data length 8-bit

Stop bit 1-bit

Parity None

Flow control hardware

Please key in the commands below to check SIM card status.

AT+CMEE=2 (enter)

OK (the response appearing on the screen)

AT+CPIN? (enter)

You may know the current status of the SIM card by reading the echo messages

you receive.

12 / 71

User manual Version 1.0

ABLELink®GPRS Serial Server SG6001

If you receive +CPIN: READY

ÆThe SIM card does not need the PIN Code.

If you receive +CPIN: SIM PIN

ÆYou need to enter the SIM card PIN code.

If you receive +CME ERROR: “SIM not inserted”

ÆPlease check if the SIM card is properly inserted.

If you receive +CPIN: SIM PUK

ÆThe SIM card has been locked because of the SIM card PIN code setting error.

Please contact the Telecom Operator to get the PUK code, and then use the mobile

phone to unlock the SIM card.

2.3 Device Attachment

SG6001 allows connecting ONE device via either serial port with DB9 connector or serial port with

terminal block. It offers RS-232/422/485 interfaces; you need to use the DIP switch to adjust according to

your device interface. Refer to the following table or the table beside the switch for detail.

SW1 (Switch 1) SW2 (Switch 2) Mode

OFF RS-232

OFF ON Console

OFF RS-485

ON ON RS-422

2.4 Power Supply Installation

a. SG6001 offers two methods to connect to power supply; however, you may only

use either the 1st or 2nd method to connect power supply.

1st. You may use the power adaptor contained in the package, connecting the jack

marked DC- IN.

13 / 71

User manual Version 1.0

ABLELink®GPRS Serial Server SG6001

2nd. Or you may use the industrial power supply to connect power supply source.

Please be careful with the voltage polarity where marked VIN- and VIN+.

b. Push power button (marked ON/OFF) to power on; push again to power off.

2.5 LED Status Indication

LED status indication can be divided into two parts:

a. Non-Console Mode

RUN COM GPRS

Flashing System

initializing

Data

transmitting

1. System initializing

2. System connecting to

Telecom Operator

3. SIM card error

Solid None None GDT successfully connects to

GGS server.

OFF None None System or GPRS error

b. Console Mode

RUN COM GPRS

*Flashing System

initializing

Data

transmitting

System initializing

Solid None None None

OFF None None System or GPRS error

* When you power on GDT, both RUN and GPRS LEDs will keep flashing

simultaneously. It indicates that GDT is initializing. When GDT finishes initializing,

RUN and GPRS LEDs will flash alternately. Then you can start configuring your

GDT.

14 / 71

User manual Version 1.0

ABLELink®GPRS Serial Server SG6001

For detailed descriptions about the GPRS LED status indication, please skip to the end

of the manual and check Appendix A: GPRS LED Status Indication Description

3. Software Installation

3.1 Overview

SG6001 provides several software that need to be installed in different sites. This

software help administrators easily configure, manage and monitor your GPRS system

in different levels. Please refer to the following descriptions and the architecture

illustration for further information.

*GGS: A server installed with GPRS Gateway Software.

*GDT: A GPRS Data Terminal

15 / 71

User manual Version 1.0

ABLELink®GPRS Serial Server SG6001

3.1.1 GGS

Your PC will become a GGS server when you install GGS (GPRS Gateway Software).

GGS is a middleware to manage and maintain large amount of GDTs (GPRS Data

Terminals).

3.1.2 ADM

ADM (Administration Manager) is a graphic user interface for administrators to manage

large amount of GDTs via GGS server. It acts as a supervisor with absolute power over

the client/server architecture shown below. Administrators can configure GGS servers

as well as specific GDT or a group of GDTs with the help of ADM software.

3.1.3 API Utility

You will install API Utility before you start using APIs to develop your application system.

Note that API is a tool for you to manage a specific GDT or specified GDT group.

3.1.4 Console Utility

Console Utility allows you to set up the parameters of your GDT and read the current

settings of your GDT from your local site. To locally configure GDT, you need to run

Console Utility in your PC or notebook. After attaching DB9 cable to your GDT and

PC/Notebook, you may start setting your GDT.

3.2 GGS (GPRS Gateway Software) Installation

You need to prepare a stand-alone computer to install GGS. However, to avoid huge

traffic ensure optimal system performance, we suggest you use our GGS-9000 as the

main terminal.

To install GGS, please follow the procedure below.

1. Insert the CD-ROM into your CD drive. Wait for a few minutes for the auto play

program to run. When the main screen appears, just click on GGS. The installation

will begin.

16 / 71

User manual Version 1.0

ABLELink®GPRS Serial Server SG6001

2. Click on Next on the installation welcome screen to continue.

17 / 71

User manual Version 1.0

ABLELink®GPRS Serial Server SG6001

3. In the next screen, please read the information of installation folder on your computer.

The default destination folder of GGS is

C:\Program Files\M2M\GGS\

Click on Next to continue. If you want to install to a different folder, click on Change.

You may click on Back to go to the previous step, or Cancel to quit.

18 / 71

User manual Version 1.0

ABLELink®GPRS Serial Server SG6001

4. Please read the current settings on the next screen. If you want to change these

settings, click on Back. If you want to start installation, just click on Install. You may

also click on Cancel if you want to quit.

19 / 71

User manual Version 1.0

ABLELink®GPRS Serial Server SG6001

5. Wait for a few seconds while installation is copying files to your computer. When it is

done, click on Finish to complete the installation.

You can find a GGS icon from StartÆProgramsÆM2M, or from C:\Program

Files\M2M\GGS. Click on the icon to run GGS on your computer

20 / 71

Table of contents

Popular GSM/GPRS Module manuals by other brands

ALERT HOUSE

ALERT HOUSE MinkPolice user manual

Quectel

Quectel LC79D (A) EVB user guide

Quectel

Quectel BC65-TE-B user guide

Teknim

Teknim TXM-0502 Installation & user manual

Interlogix

Interlogix ATS7320 Installation sheet

Quectel

Quectel M10 user guide

Quectel

Quectel EG21-G Reference design

Quectel

Quectel EG12 Series Hardware design

Neoway

Neoway N11 Series user guide

Atop ABLELink SG6001 User manual

Popular GSM/GPRS Module manuals by other brands