ATS J2200 User manual

ATA J2200-VoIP GATWAY User’s Manual
User’s Manual
for the
ATS J2200
For use with Internet Phone service by SunRocket
To enjoy all the benefits of this product, please review the
information contained in this manual

ATA J2200-VoIP GATWAY User’s Manual
Introduction....................................................................................................................................................4
Hardware Overview...................................................................................................................................4
Software Overview ....................................................................................................................................4
IVR Interface for The ATS J2200X ..............................................................................................................5
Quick Guide of ATA Network setup automatically......................................................................................7
ATA Network Setup Automatically Step By Step ........................................................................................8
Ethernet Adapter Detection .......................................................................................................................9
The Detection of the Network Environment ...........................................................................................10
DHCP User Network Environment: ........................................................................................................11
PPPoE User Network Environment:........................................................................................................12
Fix IP User Network Environment:.........................................................................................................13
To Test J2200X Network Settings:..........................................................................................................14
The Network Settings of J2200X was unsuccessful:...............................................................................15
J2200X Reboot ........................................................................................................................................16
The Installation Finished .........................................................................................................................17
Setup the ATS-J2200X by Web Browser....................................................................................................18
System Information .................................................................................................................................18
Single computer environment quick setup ..............................................................................................20
Setting Up the TCP/IP Protocol...............................................................................................................21
General Configuration .............................................................................................................................24
DHCP/Cable Users: .................................................................................................................................24
Fixed IP Users: ........................................................................................................................................24
ADSL Users (PPPoE dial-up connection): ..............................................................................................25
Multiple computers environment quick setup: ........................................................................................27
Phone Book..............................................................................................................................................29
Phone Settings .........................................................................................................................................29
Call Forwarding:......................................................................................................................................29
Volume Settings: .....................................................................................................................................30
Network ...................................................................................................................................................31
SIP Settings..............................................................................................................................................33
System Auth.............................................................................................................................................34
Save Change & Reboot............................................................................................................................35
Update......................................................................................................................................................35
Engineering webpage...................................................................................................................................36
Engineer usage webpage list....................................................................................................................36
Update.htm...............................................................................................................................................36
Natset.htm................................................................................................................................................37
Dmzset.htm..............................................................................................................................................37
Vsset.htm .................................................................................................................................................38

ATA J2200-VoIP GATWAY User’s Manual
Toneset.htm .............................................................................................................................................38
Speakerset.htm.........................................................................................................................................38
Vlanset.htm..............................................................................................................................................39
Setup the ATS-J2200X by using Console (Hyper Terminal)......................................................................40
How to make a phone call ...........................................................................................................................49
Get a FWD account .....................................................................................................................................49

ATA J2200-VoIP GATWAY User’s Manual
Introduction
This user’s manual is for ATS J2200X. It will explain the IVR instruction, web configuration
and command line configuration for the ATS J2200X. Before using the ATS J2200X, some
setup processes are required to make the ATS J2200X work properly. Please refer to the
Setup Menu for further information.
Hardware Overview
The ATS J2200X has the following interfaces for Networking, telephone interface, LED
indication, and power connector.
1.1.1 Two RJ-45 Networking interface, these two interfaces support 10/100Mps Fast
Ethernet. You can connect one RJ-45 Fast Ethernet port to the ADSL or Switch,
and connect the other one to your computer.
1.1.2 One RJ-11 Type analog telephone jack interfaces. You can connect one analog
telephone to the terminal adapter.
1.1.3 LED Indication: There are three LED indicators in the ATA-1000 to show the
Power, Register, and Off-Hook indication.
Software Overview
 Network Protocol
 SIP v1 (RFC2543), v2(RFC3261)
 IP/TCP/UDP/RTP/RTCP
 IP/ICMP/ARP/RARP/SNTP
 TFTP Client/DHCP Client/ PPPoE Client
 Telnet/HTTP Server
 DNS Client
 NAT/DHCP Server
 Codec
 G.711: 64k bit/s (PCM)
 G.723.1: 6.3k / 5.3k bit/s
 G.726: 16k / 24k / 32k / 40k bit/s (ADPCM)
 G.729A: 8k bit/s (CS-ACELP)
 G.729B: adds VAD & CNG to G.729
 Voice Quality
 VAD: Voice activity detection
 CNG: Comfortable noise generator
 LEC: Line echo canceller
 Packet Loss Compensation
 Adaptive Jitter Buffer
 Call Function
 Call Hold

ATA J2200-VoIP GATWAY User’s Manual
 Call Waiting
 Call Forward
 Caller ID
 3-way conference
 DTMF Function
 In-Band DTMF
 Out-of Band DTMF
 SIP Info
 SIP Server
 Registrar Server (three SIP account)
 Outbound Proxy
 Tone
 Ring Tone
 Ring Back Tone
 Dial Tone
 Busy Tone
 Programming Tone
 Phone Function
 Volume Adjustment
 Speed dial key
 Phone book
 Flash
 IP Assignment
 Static IP
 DHCP
 PPPoE
 Security
 HTTP 1.1 basic/digest authentication for Web setup
 MD5 for SIP authentication (RFC2069/ RFC 2617)
 QoS
 ToS field
 NAT Traversal
 STUN
 Configuration
 Web Browser
 Console/Telnet
 IVR/Keypad
 Firmware Upgrade
 TFTP
 Console
 HTTP
IVR Interface for The ATS J2200X
You can use the PSTN phone to configure the ATS J2200X. Please follow the instruction to
configure your terminal adapter.

ATA J2200-VoIP GATWAY User’s Manual
Group IVR Action IVR Menu Parameter (s) Notes
Function Reboot #195# None After you hear “Option Successful,”
hang-up. The system will reboot
automatically.
Function Factory Reset #198# None System will automatically Reboot.
WARNING: ALL
“User-Changeable” NONDEFAULT
SETTINGS WILL BE LOST! This
will include network and service
provider data.
Info Check IP Address #120# None IVR will announce the current IP
address of the ATA-1000
Info Check IP Type #121# None IVR will announce if DHCP in
enabled or disabled.
Info Check Phone Number #122# None IVR will announce current in use
VoIP number
Info Check Network Mask #123# None IVR will announce the current
network mask of the ATA-1000.
Info Check Gateway IP
Address
#124# None IVR will announce the current
gateway IP address of the
ATA-1000.
Info Check Primary DNS
Server Setting
#125# None IVR will announce the current
setting in the Primary DNS field.
Info Check Firmware Version #128# None IVR will announce the version of
the firmware running on the
ATA-1000.
Setting Set DHCP client #111# None The system will change to DHCP
Client type.
Setting Set Static IP Address #112xxx*xxx*xxx*xxx# Enter IP address using numbers on
the telephone key pad. Use the *
(star) key when entering a decimal
point.
DHCP will be disabled and system
will change to the Static IP type.
Setting Set Network Mask #113xxx*xxx*xxx*xxx# Enter value using numbers on the
telephone key pad. Use the * (star)
key when entering a decimal point.
Must set Static IP first.
Setting Set Gateway IP Address #114xxx*xxx*xxx*xxx# Enter IP address using numbers on
the telephone key pad. Use the *
(star) key when entering a decimal
point.
Must set Static IP first.
Setting Set Primary DNS Server #115xxx*xxx*xxx*xxx# Enter IP address using numbers on
the telephone key pad. Use the *
(star) key when entering a decimal
point.
Must set Static IP first.
Setting Set Codec #130+[1-8]# 1:G.711 u-Law, 2: G.711 a-Law, 3:
G.723.1, 4: G.729a, 5: G.726 16K,
6: G.726 24K, 7: G.726 32K, 8:
G.726 40K,
You can set the codec you want to
the first priority.
Setting Set Handset Gain #131+[00~15]# Handset Gain from 0~15 You can set the Handset gain to
proper value, default is 6.
Setting Set Handset Volume #132+[00~12]# Handset Volume from 0~12 You can set the Handset volume to
proper value, default is 10.

ATA J2200-VoIP GATWAY User’s Manual
Quick Guide of ATA Network setup automatically
You can enjoy the ATA free and relaxed with connect network. You just connect it by following
step, you do talk to anybody with the ATA.
Refer to the Connection Graph above; connect ATS-J2200X with your personal computers and
telephone:
 Connect your modem and WAN port of ATS-J2200X with network cable.
 Connect your computer and LAN/PC port of ATS-J2200X with network cable
 Connect your telephone cable to the phone port of ATS-J2200X.
 Connect the power cord to ATS-J2200X power port.
According to the connection with ATS-J2200X will be installed network setting automatically

ATA J2200-VoIP GATWAY User’s Manual
until put on the CD-ROM. The installation will lead you set up the Ethernet by step
automatically.
Step1: To make sure the connection between your computer with the ATA Box.
Step2: Put the installed CD-ROM into the computer CD-ROM drive.
Step3: The installation will be implemented automatically.
Step4: Just wait about 3~5 minutes until the ATS-J2200X set up ready. It has to take so much
time while you set up the ATS-J2200X at first time, Please hold on a minute.
Step5: After the ATA finished setting network condition, the ATA will reboot and download the
web configure file by itself automatically. You will see the REG LED ON then you can
pick the phone up and enjoy your calling with the ATA. And the computer will be working
well by installing automatically.
ATA Network Setup Automatically Step By Step
While user put on the CD-ROM and auto run by drive, the information page will show on your
screen step by step.

ATA J2200-VoIP GATWAY User’s Manual
Ethernet Adapter Detection
The installation will check out your computer Ethernet adapter first if you have more than one
piece of Ethernet adapters. If you have two Ethernet adapters at least, you have to select the
Ethernet adapter you would like to work with internet. Otherwise you will skip this step of
installation.

ATA J2200-VoIP GATWAY User’s Manual
The Detection of the Network Environment
The installation is detecting the network environment with J2200X what network type is.
Please wait…

ATA J2200-VoIP GATWAY User’s Manual
DHCP User Network Environment:
The installation will auto detect your network environment after put on the CD-ROM with
connection of ATA. Just wait 5 minutes the ATA will detect the DHCP network or Cable Modem
network by itself and set your computer to DHCP mode automatically. While the ATA reboot
and REG LED ON with the installation had finished. Then you can get to call with ATA and the
computer will get DHCP IP from the ATA LAN/PC port.

ATA J2200-VoIP GATWAY User’s Manual
PPPoE User Network Environment:
The installation will auto detect your network environment after put on the CD-ROM with
connection of ATA. Just wait 5 minutes the ATA will detect the PPPoE network by itself and
setup your computer to DHCP mode automatically.
1. By detecting PPPoE settings with connection of the ATA, while the page lead you to dial
the PPPoE from your computer, you have to click the PPPoE dialer on your computer to
connect internet and make sure you do connect the internet successful.
2. The ATA PPPoE detection will auto set according to your PPPoE dialer through your
computer.
3. Just wait for 3~5 minutes the ATA will set itself well. If it failed, please redial PPPoE
function from the computer.
4. Then the ATA had been installed successfully and the computer had been set for DHCP
client to get new IP from the ATA LAN/PC port.

ATA J2200-VoIP GATWAY User’s Manual
Fix IP User Network Environment:
The installation will auto detect your network environment after put on the CD-ROM with
connection of ATA. Just wait 5 minutes the ATA will detect the Fix IP network by itself and setup
your computer to DHCP mode automatically.
While the ATA reboot and REG LED ON with the installation had finished. Then you can get to
call with ATA and the computer will get DHCP IP from the ATA LAN/PC port.

ATA J2200-VoIP GATWAY User’s Manual
To Test J2200X Network Settings:
After network environment settings, the J2200X is testing the network settings by itself. Just
hold on…

ATA J2200-VoIP GATWAY User’s Manual
The Network Settings of J2200X was unsuccessful:
Maybe the system didn’t detect the network environment successful. Please proceed the
detection of network environment (Step Ⅱ) again.

ATA J2200-VoIP GATWAY User’s Manual
J2200X Reboot
Please wait for J2200X rebooting…

ATA J2200-VoIP GATWAY User’s Manual
The Installation Finished
The system executes the network settings successful. On another hand, the J2200X has
downloaded the web configure file from provider automatically. Please check out the J2200X
REG LED ON and the computer is working well. Then you can enjoy having a call with J200X.

ATA J2200-VoIP GATWAY User’s Manual
By foregoing step you still couldn’t set the J2200X network settings, you have to setup
the J2200X network settings by login into J2200X web browser.
Setup the ATS-J2200X by Web Browser
The ATS-J2200X provides a built-in web server. You could use Web browser (Internet Explorer,
Mozilla Firefox etc.) to configure ATS-J2200X.
1. Launch your web browser and enter http://192.168.251.1 (the default IP address of the
ATS-J2200X) in the Location or Address field. Press Enter.
2. The password screen now appears. Input username: user and password: test into the
blank field.
3. Click the [Login] button
4. After a successful login, you will see the ATS-J2200X web based management information
page.
Note: If you make any change of settings in the Web Management interface, please do
remember to click the [Submit] button in that page. A message showed you have to
save and reboot the VoIP to take effect notice you to click [Save change & Reboot] on
the navigation panel and click [Save] in the Save changes page. After the system reboot,
all the settings will work properly.
System Information
 This is the web based management information page, you can see the ATS-J2200X
current system information like firmware version, company… etc in this page.
 Click a link on the navigation panel to go to the corresponding function.

ATA J2200-VoIP GATWAY User’s Manual
Table of Navigation Sub-Manu Description
Phone Book Speed Dial Setting Setup the Speed Dial number Speed Dial
Phone information.
Call Forwarding You can set the forward number of your
phone on this page.
SNTP Settings You can set the SNTP servers on this page.
Volume Settings You can set the volume of your phone on this
page.
Block Settings You can set the block period of your phone
on this page.
Caller ID Settings You can enable/disable the caller ID setting
on this page.
Dial Plan Settings You can the set the dial plan on this page.
Flash Time Settings You can set the flash time on this page.
Call Waiting Settings You can enable/disable the call waiting
setting on this page.
Phone Settings
T.38 (FAX) Settings You can enable/disable the FAX function on
this page.
Network Status This page shows current status of network
interfaces of the system.
WAN Settings You can configure the WAN settings on this
page.
Network
LAN Settings You can configure the LAN settings on this
page.
Service Domain Settings You can set information of service domains
on this page.
Port Settings You can set the port number in this page.
Codec Settings You can set the codec settings on this page.
Codec ID Setting You can set the value of Codec ID on this
page.
DTMF Setting You can set the DTMF setting in this page.
RPort Setting You can enable/disable the RPort setting on
this page.
SIP Settings
Other Settings You can set other settings on this page.
System Authority You can change the login username /
password on this page.
Save Change &
Reboot
You have to save changes and reboot
ATS-J2200X to com into effect.
Update Firmware You can update the newest firmware.Update
Restore Default Settings You can click the restore button to restore the
factory settings.

ATA J2200-VoIP GATWAY User’s Manual
Single computer environment quick setup
Refer to the Connection Graph above; connect ATS-J2200X with your personal computers and
telephone:
 Connect your modem and WAN port of ATS-J2200X with network cable.
 Connect your computer and LAN port of ATS-J2200X with network cable
 Connect your telephone cable to the phone port of ATS-J2200X.
 Connect the power cord to ATS-J2200X power port.
Power LED will be ON. The start-up process will take approximately 20 seconds.
 REG LED ON: You may start to use VoIP services and make any phone calls.
 REG LED OFF: Internet status error. The ATS-J2200X is not successfully connected with
internet. Please follow the steps below to configure ATS-J2200X.