attica ATTFB01C102-BX User manual

ATTFB01C102-BX
[e-mail] [phone]
Before installation - Read and understand all instructions,
warnings, cautions, and notes contained in this installation
instruction guide. Consult your vehicle owner’s manual for proper
disconnection of electrical and liting of vehicle if required for
installation of this product.
This install may require some technical skills and knowledge of basic
mechanical work. If you do not feel that you are capable of performing
this install please take this product to a trained professional.
Ater reading this guide please contact us with any questions or
concerns before installing product.
Customer Service: [phone]
ATTICA4X4 is not responsible for any bodily injury or harm to you or
your vehicle as a result of an improper install.
Proper installation of this kit requires knowledge of the factory
recommended procedures for removal and installation of original
equipment components. We recommend that the factory shop manual
and any special tools needed to service your vehicle be on hand
during the installation. Installation of this kit without proper
knowledge of the factory recommended procedures may aect the
performance of these components and the safety of the vehicle.
Always wear eye protection when operating power tools.
Inspect all contents of this package to make sure product is not damaged and all
installation hardware has been included. If parts are missing from kit, please be
prepared to provide the following information:
• Name of purchase location
• Bar Code on side of box • Date above Bar Code • Date insde box cover
Ford Bronco
18-23
Terra Series Side Steps

13942 VALLEY BLVD, CITY OF INDUSTRY, CA 91746
[e-mail]
626-369-2121
WWW.ATTICA4X4.COM
tools required
hardware kit
•16mm socket
•18mm socket
x 1
SPARE PARTS HARDWARE KIT
W27 | Washer
x 17
N15 | Hex Flange Nut
x 4
W23 | Washer
x 12
N19 | Hex Flange Nut
x 7
x 2
threaded plate
W22 | washer
x 8
W25 | washer
x 12
x 5
b37 | bolt
B58
x 8
x 8
b35 | bolt

13942 VALLEY BLVD, CITY OF INDUSTRY, CA 91746
[email protected]
626-369-2121
WWW.ATTICA4X4.COM
Begin by unpacking all items and inspecting them
for damage or missing items. Any concerns, please
contact the company you purchased the side
steps from.
To prevent damaging your gas tank, use the
supplied W25 lock washer with the thicker washer
for the passenger’s side middle mounting point.

13942 VALLEY BLVD, CITY OF INDUSTRY, CA 91746
[email protected]
626-369-2121
WWW.ATTICA4X4.COM
For the driver’s side front mounting point, use B58 bolt and W27 washer as
shown to the top let. Use the oversized washer with W25 lock washer and
N19 nut as shown to the top right.
For the bottom bolt, use B37 bolt, W25 lock washer and W27 washer with
the threaded plate (Feed the threaded plate into the frame).
Attach the supporting bracket to the driver’s
side front mounting point, using B35 bolt,
W22 lock washer and W23 washer, with the
N15 nut.

13942 VALLEY BLVD, CITY OF INDUSTRY, CA 91746
[email protected]
626-369-2121
WWW.ATTICA4X4.COM
For the driver’s side middle mounting point, use B58 bolt and W27 washer as shown to
the top let. Use the W27 washer with W25 lock washer and N19 nut as shown to the
top right. (Do not use the oversized washer for this mounting point.)

13942 VALLEY BLVD, CITY OF INDUSTRY, CA 91746
[email protected]
626-369-2121
WWW.ATTICA4X4.COM
For the driver’s side rear mounting point, use B58 bolt and W27 washer
as shown to the top let. Use the oversized washer with W25 lock
washer and N19 nut as shown to the top right.
Attach the supporting bracket to the driver’s
side rear mounting point, using B35 bolt,
W22 lock washer and W23 washer, with the
N15 nut.

13942 VALLEY BLVD, CITY OF INDUSTRY, CA 91746
[email protected]
626-369-2121
WWW.ATTICA4X4.COM
For the passengers side front mounting point, use B58 bolt and W27
washer as shown to the top let. Use the oversized washer with W25 lock
washer and N19 nut as shown to the top right.
For the bottom bolt, use B37 bolt, W25 lock washer and W27 washer with
the threaded plate (Feed the threaded plate into the frame).
Attach the supporting bracket to the
passenger’s side front mounting point, using
B35 bolt, W22 lock washer and W23 washer,
with the N15 nut.

13942 VALLEY BLVD, CITY OF INDUSTRY, CA 91746
[email protected]
626-369-2121
WWW.ATTICA4X4.COM
For the passenger’s side middle mounting point, use B58 bolt and the thick washer
with W25 lock washer as shown to the top right. Use the oversized washer with W25
lock washer and N19 nut to mount to the frame.
Take note of the distance between the bolt and gas tank, if more clearance is needed,
W27 washer can be added.

13942 VALLEY BLVD, CITY OF INDUSTRY, CA 91746
[email protected]
626-369-2121
WWW.ATTICA4X4.COM
For the passengers side rear mounting point, use B58 bolt and W27
washer as shown to the top let. Use the oversized washer with W25
lock washer and N19 nut as shown to the top right.
Attach the supporting bracket to the
passenger’s side rear mounting point, using
B35 bolt, W22 lock washer and W23 washer,
with the N15 nut.
Once finished your Attica Terra Series Side
Steps will be completely installed and ready
to take to the outdoors!

[e-mail] [phone]
if you have any questions, please email us at [e-mail] or call us at
626-369-2121