attika RAIS VISIO 1 User manual

BRUGERMANUAL
BEDIENUNGSANLEITUNG
USER MANUAL
MANUEL D’UTILISATEUR
BRUKERVEILEDNING
BRUKSANVISNING
KÄYTTÖOHJE
GEBRUIKERSHANDLEIDING
VISIO 1
VISIO 2
VISIO 3

We cannot be held responsible for any misprints.
RECYCLING:
The oven is wrapped in packaging that is recyclable. This
must be disposed of according to national rules regard-
ing the disposal of waste.
The glass can not be reused.
The glass should be discarded along with the residual
waste from ceramics and porcelain.
Pyrex glass has a higher melting temperature and there-
fore can not be reused.
If discarded you make an important positive contribution
to the environment.
FIRE ENVIRONMENTALLY FRIENDLY!
5 Eco-friendly advices for sensible heating
- common sense both environmentally and economically.
1. Effective lighting. Use small pieces of wood (fir tree) and a
suitable fire lighter, for example paraffined wood wool/saw-
dust. Open the air damper, so plenty of air is fed to the stove
and the gases from the heated wood can burn rapidly.
2. Light the fire with only little wood at a time - this gives the
best combustion. Remember plenty of air for every time new
wood is added.
3. When the flames are diminished, adjust the air damper so that
the air supply is reduced.
4. When only glowing embers remain, air flow can be reduced
further, so heating demand is just covered. With a lower air
supply the charcoal will burn slower and the heat loss through
the chimney is reduced.
5. Use only dry wood - ie. wood with a humidity of 15 to 20%.

8
VISIO
10
28-03-2017
8
English RAIS/ attika - U ser manual for VISIO
Revision :
Date :
INTRODUCTION......................................................................................................................9
WARRANTY..........................................................................................................................10
SPECIFICATIONS ...................................................................................................................11
DISTANCES...........................................................................................................................12
CONVECTION.......................................................................................................................17
MATERIAL SELECTION...........................................................................................................17
CHIMNEY .............................................................................................................................18
INSTALLATION INSTRUCTIONS ..............................................................................................20
INSTALLATION ......................................................................................................................21
INSTALLATION DISTANCES....................................................................................................21
MOUNTING THE REFLEKTOR PLATE.......................................................................................22
REMOVING THE TRANSPORT SAFETY ...................................................................................23
VISIO 1 - BUILT-IN DIMENSIONS.............................................................................................24
VISIO 1 - INSTALLATION DISTANCES......................................................................................29
VISIO 2 - BUILT-IN DIMENSIONS.............................................................................................35
VISIO 2 - INSTALLATION DISTANCES......................................................................................40
VISIO 3 - BUILT-IN DIMENSIONS.............................................................................................46
VISIO 3 - INSTALLATION DISTANCES......................................................................................48
AIR-SYSTEM .........................................................................................................................54
FOR THE INSTALLER ..............................................................................................................54
FUEL.....................................................................................................................................55
DRYING AND STORAGE........................................................................................................56
REGULATING THE COMBUSTION AIR....................................................................................56
ROOM VENTILATION.............................................................................................................56
USING THE WOOD BURNING STOVE.....................................................................................57
FIRST USAGE ........................................................................................................................57
LIGHTING AND FUELLING .....................................................................................................58
CONTROL.............................................................................................................................59
WARNING ............................................................................................................................60
CLEANING AND CARE ..........................................................................................................61
CLEANING THE DOOR GLASS - VISIO 1.................................................................................62
CLEANING THE DOOR GLASS - VISIO 2.................................................................................63
CLEANING THE DOOR GLASS - VISIO 3.................................................................................64
CLEANING THE COMBUSTION CHAMBER.............................................................................65
CLEANING OF FLUE WAYS....................................................................................................65
INTERRUPTION OF OPERATION..............................................................................................66
CONVERSION TO SELV CLOSING DOOR................................................................................68
ACCESSORIES.......................................................................................................................70
SPARE PARTS VISIO 1............................................................................................................72
SPARE PARTS VISIO 2 & 3......................................................................................................73
DECLARATION OF PERFORMANCE........................................................................................74

99
English RAIS/ attika - U ser manual for VISIO
Introduction
Thank you for purchasing a RAIS/ attika wood burning stove.
A RAIS/ attika wood burning stove is more than just a heat source. It also shows that
you care about design and quality in your home.
To make the most of your wood burning stove it is important that you read the manual
thoroughly, before installing and using it.
In the case of warranty coverage, and for general queries regarding your wood burn-
ing stove, it is important that you know the stove’s production number. We therefore
recommend that you write down the number in the table below.
The production number is located on the side of the stove at the bottom.
Date: Distributor:

1010
English RAIS/ attika - U ser manual for VISIO
WARRANTY
RAIS/ attika – wood-burning stoves are tested repeatedly in terms of safety, as well as
material and manufacturing quality. We grant warranty on all models, starting with the
date of installation.
The warranty refers to:
• documented malfunctions due to faulty manufacture
• documented material defects
The warranty does not cover:
• door and glass seals
• ceramic glass
• chamber lining
• appearance of the surface structure or natural stone texture
• appearance or changes of colour of the stainless steel or patina surfaces
• expansion noise
The warranty is invalidated in case of:
• damages, caused by overfiring
• damages, caused by external influence and the use of unsuitable fuels
• non-observance of statutory or recommended installation guidelines, and modifi-
catons to the wood-burning stove
• non-observance of service and care provisions
Please contact your retailer in the event of damage. We determine the way to repair
the damage, in case of warranty claims. In the event of repair, we ensure proper and
professional execution.
Warranty claims submitted for additionally delivered or repaired parts are subject to
national/EU laws and regulations in terms of renewed warranty periods.
Please contact RAIS A/S for the applicable warranty provisions.

11
DTI
Danish Technological Institute
Teknologiparken Kongsvang Allé 29, DK-8000 Aarhus C
Danmark
www.dti.dk
Telefon: [phone]
Fax: [phone]
English RAIS/ attika - U ser manual for VISIO
DTI ref.: 300-ELAB-2080-EN / 300-ELAB-
2080-AEA
VISIO 1 VISIO 2 VISIO 3
Nominal output (kW): 7
Min./Max. output (kW): 5 - 9
Heating area (m2): 75 - 120
Stove’s width/depth/height (mm): 867/550/1226 833/593/1617 759/564/1616
Combustion chamber’s width/depth/
height (mm): 697/333/450 533/333/466 533/333/466
Recommended amount of wood
when fuelling (kg).
Distributed on 2-4 logs of wood of
approx. 30 cm
1.5 - 2.5
Min. uptake / Min. draught (Pascal): -12
Weight (kg): approx 233
Efficiency (%): 80
CO-emission at 13% O2(%): 0.092
NOx-emission at 13% O2(mg/Nm³): 81
Particles emission acc. to
NS3058/3059 (g/kg): 6.507
Dust measured acc. to Din+ (mg/
Nm³): 5
Smoke gas mass flow (g/s): 7.5
Smoke gas temperature (°C): 243°
Smoke gas temperature (°C) at flue
collar: 292°
Intermittent operation: Refuelling should be
undertaken within 49 minutes.
Specifications
RAIS/ attika VISIO are inset stoves with a vertically operated door.
VISIO 1 has a front glass
VISIO 2 has a front glass and a side glass either to the right or left.
VISIO 3 has a front glass and 2 side glasses.

12
Established:
Designer: Project manager:
Format:
Approved:
Drawing no.:Revision:Project:
Drawing name:
INDUSTRIVEJ 20, 9900 FREDERIKSHAVN, DENMARK
Phone [phone] - Fax [phone]
E-mail: [e-mail] - Homepage: www.rais.dk
Corrections:
D M Y
nra
Visio 1 måltegning
20-05-2015 A3
Visio
354 - 454
151
430
77
373
-10
15
+
452,5(N)
741
77
1375,5
-10
15
+
1643
-10
15
+
198Ø
307 - 507
132(K)
369
1526
-10
15
+
(I)
908
540
1395
(J) 198
Ø
684
548
12
English RAIS/ attika - U ser manual for VISIO
DIstances
I: Distance from floor to center smoke top outlet
J: Distance from floor to center smoke back outlet
K: Distance from back side to air intake bottom (air system)
N: Distance from side to air intake bottom (air system)
Note that the stoves are fitted with a stepless flue collar.
VISIO 1

13
Måltegning
VISIO 2 (LEFT)
1249006 - Topafgang
4 positioner af røgafgang.
Studs kan dreje trinløst.
Røgrør er drejet
til bagerste position
Røgrør er drejet
til forreste position
Røgrør er drejet
til højre position
1367,5 -10
15
+
330 - 529
330,85
529,15
428,9 230,7
228 - 428
430
167,5
161
1535 -10
15
+
(I)
369
564
384,5 -10
15
+
Røgrør er drejet
til venstre position
833
549
29
29
398(N) 133(K)
1617 -10
15
+
198
13
English RAIS/ attika - U ser manual for VISIO
VISIO 2 with smoke top outlet

14
Måltegning
VISIO 2 (LEFT)
1249006 - Bagafgang
2 positioner vist af røgafgang.
Studs kan dreje trinløst.
Røgrør er drejet
til bagerste position
660
Røgrør er drejet
til højre position
198

1404 -10
15
+
(J)
560
548
14
English RAIS/ attika - U ser manual for VISIO
VISIO 2 with smoke back outlet

15
280 - 480
1616 -10
15
+
185
29,5
564
430
29,5
384,5 -10
15
+
1537 -10
15
+
564
759
39,5
418218 -
369
158(K)
Måltegning
VISIO 3
1249008 - Topafgang
1351,5 -10
15
+
380(N)
198
15
English RAIS/ attika - U ser manual for VISIO
VISIO 3 with smoke top outlet

16
Måltegning
VISIO 3
1249008 - Bagafgang
1406 -10
15
+
(J)
549
564
198

16
English RAIS/ attika - U ser manual for VISIO
VISIO 3 with smoke back outlet

17
Måltegning
VISIO 3
1249008 - Bagafgang
1406 -10
15
+
(J)
549
564
198

17
English RAIS/ attika - U ser manual for VISIO
Convection
RAIS/ attika stoves are convection stoves. Convection means that there is a circula-
tion of air, which ensures that the heat is distributed more evenly throughout the entire
room. The cold air is sucked in at the base of the stove up through the convection
channel, which runs along the stove’s combustion chamber.
The heated air pours out at the top of the stove, which ensures a circulation of warm
air throughout the room.
Note, however, that all exterior surfaces become hot during use - so take extreme care.
Use the insert optimally.
By installing hot air nozzles and flexible hoses (or similar) on top of the stove, it is pos-
sible to ”move” the heat to other rooms.
Consider the placement of convection and outlet holes. Ensure that the area require-
ments are respected and that the holes are not blocked from the outside. There may
be discoloration of the wall above the stove doors, and above the convection outlet
holes. This is due to the ascending hot air.
RAIS/ attika accepts no liability for installation or consequential damages.
Material selection
Choose non-combustible materials for panels/bricks with a thermal resistance greater
than 0.03 m2xK/W. Thermal resistance is defined as the thickness (in m) divided by the
wall’s lambda value. Consult with your installer/chimney sweep.

1818
English RAIS/ attika - U ser manual for VISIO
Chimney
The chimney is the driving force which makes the stove function. In order for the stove
to perform satisfactorily the chimney height must be sufficient to ensure the correct
draught of 14 to 18 Pa so as to clear the products of combustion and prevent problems
of smoke emanating into the room when firing.
NOTE: A chimney height of not less than 4.5 metres measured vertically from the outlet
of the stove to the top of the chimney should be satisfactory. Alternatively the calcula-
tion procedure given in BS 5854:1980 may be used as the basis for deciding whether a
particular chimney design will provide sufficient draught.
The outlet from the chimney should be above the roof of the building in accordance
with the provisions of Building Regulations Approved Document J.
If installation is into an existing chimney then it must be sound and have no cracks or
other faults which might allow fumes into the house. Older properties, especially, may
have chimney faults or the cross section may be too large i.e. more than 230 mm x 230
mm. Remedial action should be taken, if required, seeking expert advice, if necessary. If
it is found necessary to line the chimney then a flue liner suitable for solid fuel must be
used in accordance with Building Regulations Approved Document J.
Any existing chimney must be clear of obstruction and have been swept clean immedi-
ately before installation of the stove. If the stove is fitted in place of an open fire then
the chimney should be swept one month after installation to clear any soot falls which
may have occurred due to the difference in combustion between the stove and the
open fire.
If there is no existing chimney then either a prefabricated block chimney in accordance
with Building Regulations Approved Document J or a twin walled insulated stainless
steel flue to BS 1856-1 can be used. These chimneys must be fitted in accordance with
the manufacturer’s instructions and Building Regulations.
A single wall metal fluepipe is suitable for connecting the stove to the chimney but is
not suitable for using for the complete chimney. The chimney and connecting fluepipe
must have a minimum diameter of 180 mm. Any bend in the chimney or connecting
fluepipe should not exceed 45°. 90°bends should not be used.
Combustible material should not be located where the heat dissipating through the
walls of fireplaces or flues could ignite it. Therefore when installing the stove in the
presence of combustible materials due account must be taken of the guidance on the
separation of combustible material given in Building Regulations Approved Document J
and also in these stove instructions.
If it is found that there is excessive draught in the chimney then either an adjustable
flue damper or alternatively a draught stabiliser should be fitted. The adjustable flue
damper should not close off the flue entirely but should in its closed position leave a
minimum continuous opening free area of at least 20 % of the total cross sectional
area of the flue or fluepipe.
During the test, the stove was installed into a test enclosure arrangement made of 12,5
mm Fermacell H2O Powerboard non-combustible building slabs. The inner side of the
test enclosure was insulated with 25 mm mineral wool, type ProRox SL970 SC from
Rockwool.
The stove was also tested against a back wall of Super Isol (calcium silicate insulating
boards).

1919
English RAIS/ attika - U ser manual for VISIO
Adequate provision e.g. easily accessible soot door or doors must be provided for
sweeping the chimney and connecting fluepipe.
You should also familiarise yourself with the draught conditions for chimneys with 2
flues.
The stove is supplied with a ø200 mm flue outlet spigot.
The stove is approved with a ø180 mm flue outlet spigot, which can be retrofitted.
The flue spigot can be changed from top outlet to back
outlet. The clamp on the outlet is loosened and
adjusted as desired.
NOTE!
if the stove is installed with a back outlet, the back wall
must be non combustible ( e.g.a brick wall).
For strong draughts, the chimney or flue should be fitted
with a draught stabiliser. In which case, it is important to
ensure that there is a free flow-through area of minimum
20 cm² when the regulating gate is shut. Otherwise, the
fuel energy may not be used optimally. If, at any time, you
are unsure about the condition of the chimney, you should contact a chimney sweep.
Remember that access to the access door should be kept clear.
Make sure to establish access to cleaning the stove, flue collar and pipe.

2020
Installation instructions
The following pages give instructions for the safe and proper installation of this heat-
ing appliance in the UK. These instructions cover the basic principles of installation,
although detail may need slight modification to suit particular local site conditions. In
all cases the installation must comply with current UK Building Regulations, Local Au-
thority Byelaws and other specifications or regulations as they affect the installation of
the stove. Please note that it is a legal requirement under England and Wales Building
Regulations that the installation of the stove is either carried out under Local Author-
ity Building Control approval or is installed by a Competent Person registered with a
Government approved Competent Persons Scheme. HETAS Ltd operate such a Scheme
and a listing of their Registered Competent Persons can be found on their website at
www.hetas.co.uk.
It should be noted that the current Building Regulations requirements are given in
Approved Document J. These requirements may also be met by adopting the relevant
recommendations given in British Standards BS 8303 and BS EN 15287-1.
WARNING: Health and Safety Advice Notice
The installation of this heating appliance is governed by the Health and Safety at Work
Act 1974. It is the responsibility of the installer to ensure that all requirements of this
Act are met during the installation works. Attention is drawn in particular to the follow-
ing:
Handling
The appliance is a heavy item and adequate facilities must be available for loading,
unloading and site handling.
Fire Cement
Some types of fire cement are caustic and should not be allowed to come into contact
with the skin. Protective gloves should be worn when handling fire cement. In case of
contact with the skin wash immediately with plenty of water.
Asbestos
This stove contains no asbestos. If there is a possibility of disturbing any asbestos in the
course of installation then please seek specialist guidance and use appropriate protec-
tive equipment.
Metal Parts
When installing or servicing this stove care should be taken to avoid the possibility of
personal injury.
Important Warning –Preparatory Work and Safety Checks:
• This stove must not be installed into a chimney that serves any other heating appli-
ance.
• It’s recommended not have an extractor fan fitted in the same room as the stove as
this can cause the stove to emit fumes into the room.
• If this appliance is installed into an existing chimney, the chimney must first be
swept and examined for soundness and suitability before the appliance is installed
(see also section headed “Chimney”).
NOTE!!
This appliance may only be installed by a qualified RAIS dealer/installer.
See www.rais.com for dealer list.
English RAIS/ attika - U ser manual for VISIO

2121
Installation distances
To determine whether the wall next to where the stove is going to be installed is flam-
mable, you should contact your building contractor or the local building authorities.
The hearth should be able to accommodate the weight of the stove. The chimney must
be independently supported by wall brackets or a ceiling support plate. The weight of
the stove is indicated in the brochure.
The stove should always be installed on a non-combustible hearth of a size and con-
struction that is in accordance with the provisions of the current UK Building Regula-
tions Approved Document J.
If the stove is to be installed on a wooden floor, it must be covered with a non-com-
bustible material at least 12 mm thick, in accordance with UK Building Regulations
Approved Document J, to at distance of 225 mm in front of the stove and 150 mm to
each side measuring from the door of the combustion chamber.
The clearance distances to combustible material beneath, surrounding or upon the
hearth and walls adjacent to the hearth should comply with the guidance on the sepa-
ration of combustible material given in UK Building Regulations Approved Document J
and also in these stove instructions.
It must be ensured that no combustible objects (eg. furniture) are placed closer than
the distances given in the following tables (risk of fire).
Installation
This appliance may only be installed by a qualified Rais dealer/installer, otherwise the
warranty is voided.
When installing the appliance, all local rules and regulations, including those referring
to national and European standards need to be complied with. Local authorities and a
chimney specialist should be contacted prior to set up.
It is prohibited to carry out unauthorised alterations to the stove.
There must be plenty of fresh air in the room where the stove is being installed, in
order to ensure proper combustion. Note that any mechanical exhaust ventilation - e.g.
an extraction hood - may reduce the air supply. Any air grates must be placed in such
a manner, that the air supply is not blocked. Alternatively, the stove is supplied with
fresh air directly from the outside through a flex tube fitted to the damper (see section
‘Airsystem’).
The floor structure must be able to carry the weight of the wood burning stove, as
well as the weight of a chimney, if necessary. If the existing floor construction doesn’t
meet this requirement, suitable measures (e.g. load distributing plate) shall be taken to
achieve it. RAIS recommends to consult a building expert.
The stove is placed on fireproof material.
The stove should be set up at a safe distance from inflammable materials.
When you choose where to set up your RAIS wood burning stove, you should consider
the heat distribution to the other rooms. This will enable you to get the best use out of
your stove.
See the manufacturer’s plate on the wood burning stove.
Upon receiving the stove must be inspected for defects.
English RAIS/ attika - U ser manual for VISIO

2222
English RAIS/ attika - U ser manual for VISIO
Mounting the reflektor plate - VISIO 1 & 2
The stove is fitted with a reflector
plate on the back side. Dismount the reflector plate and
turn it upside down. Mount the
plate reusing the screws (as shown).
Mounting the reflector plate - VISIO 3
The stove is fitted with a
reflector plate. Dismount the reflector plate and turn it upside down. Mount the plate by reus-
ing the screws at the bottom.

2323
English RAIS/ attika - U ser manual for VISIO
Bend the cut-outs and mount
the plate to the top of the
stove.
Transport safety
Before installing the stove remove the transport safety:
• on VISIO 1 remove 2 screws on the side.
• on VISIO 2 remove 1 screw on the side.
• on VISIO 3 remove 2 screws on the back side.
Mounting the reflector plate - VISIO 3

24
Established:
Designer: Project manager:
Format:
Approved:
Drawing no.:Revision:Project:
Drawing name:
INDUSTRIVEJ 20, 9900 FREDERIKSHAVN, DENMARK
Phone [phone] - Fax [phone]
E-mail: [e-mail] - Homepage: www.rais.dk
Corrections:
D M Y
user
VISIO 1 Indbygningsmål kun Panel
04-05-2015 A3
24
English RAIS/ attika - U ser manual for VISIO
Wall opening VISIO 1 - calcium silicate insulating boards
Wall opening (height x width x depth) min. 432 x 770 mm (inner dimensions).
Inner distance to the back wall is min. 620 mm and to the side wall it is min. 1047 mm.
In case the stove is placed against a combustible wall, the back and side walls must be
made of 50 mm calcium silicate insulating boards.
The inner dimensions (wall opening) applies for installing the stove without outer front
cover (accessory). If a front cover is used, the wall opening is to be increased/corrected
equalling the thickness of the front cover.
A fireplace insert must never be built in tightly as steel expands during heating.
12,5 mm Fermacell eller
50 mm calcium silicate
bords

25
Established:
Designer: Project manager:
Format:
Approved:
Drawing no.:Revision:Project:
Drawing name:
INDUSTRIVEJ 20, 9900 FREDERIKSHAVN, DENMARK
Phone [phone] - Fax [phone]
E-mail: [e-mail] - Homepage: www.rais.dk
Corrections:
D M Y
user
VISIO 1 Indbygningsmål kun Panel
04-05-2015 A3
A-A
B-B
A
A
B B
E E
VISIO 2 (uden afdækning)
Panel indbygning
Uden tekst
200
25
English RAIS/ attika - U ser manual for VISIO
VISIO 1 - Built-in dimensions
Wall opening VISIO 2 - 12.5 mm Fermacell with 25 mm mineral wool
Wall opening (height x width x depth) min. 432 x 770 mm (inner dimensions).
Inner distance to the back wall is min. 620 mm and to the side wall it is min. 1047 mm.
In case the stove is placed against a combustible wall, the back and side walls must be
made of 12.5 mm Fermacell + 25 mm mineral wool. The mineral wool is facing the
stove.
The inner dimensions (wall opening) applies for installing the stove without outer front
cover (accessory). If a front cover is used, the wall opening is to be increased/corrected
equalling the thickness of the front cover.
A fireplace insert must never be built in tightly as steel expands during heating.
25 mm mineral wool
12,5 mm Fermacell
Construction of back & side wall.
12,5 mm Fermacell