decoflame TOKYO User manual

NICE ROUND TABLE TOP™
www.decoflame.com
TOKYO™
WITH DENVER E-RIBBON BASIC BURNER
Decoame Technical Information
Standard finiSh
Tokyo is a gorgeous round bio replace with a horizontal
half-circle across the lowest part of the replace.
The depth of Tokyo increases at the bottom, creating an
inclined edge, which is especially present when seen from
the side.
This bio replace can be built-in as a recess in a wall and
can therefore be utilized in more than one way and do not
require that much space.
technical information
Capacity: 4L
Burning time: 7-20 hours (Depending on ameintensity)
Heat e󰀩ency: 3,2 kW/h
Net weight: 27 kg
Room size: 643
Burner: Denver e-Ribbon Basic 670
Flametray: 450mm
Materials: Aluminium and 6mm hardened glass
Finish: Standard: Black
Front: Black / White / Polished steel / Brushed steel
Brushed copper / Brushed brass
Power supply: 220V - 240V / 50 Hz
Fuel: Use bioethanol at 96,5 - 97,5%
featureS
• e-Ribbon™ technology
• Safety Sensors / Safety Chamber
• Fuel Level Indicator / Flame Level Indicator
• Remote control
• Bluetooth / App
• 6 ame levels (1-5 + ECO-Wave)
• No chimney required - no smoke, ash or soot
acceSSorieS
• Fuel Funnel / Sponge
Bioethanol
For use and information about bioethanol, please visit our webiste decoame.com.
(Please be aware that bioethanol is essential to a proper use and gurantee of your product).
Black
Polished
front finiSh
Black White BSS Brushed
brass
Brushed
copper
830,00
97,91
256,95
8,00

1. Download and install the Decoame App by
scanning the QR code above corresponding to
your smart device’s operating system.
4. Once you have selected your replace, you
can turn it on by pressing ‘START’. If the re-
place has already been turned on using the
control panel, you can now monitor the fuel
level and the consumption.
5. For the ‘Turn O󰀨 Timer’ press the clock icon
in the lower right corner. To adjust the remain-
ing time, slide the dot to the left and right and
select ‘SET TIMER’. The remainig burning
time can be changed by repeating the above
mentioned steps. To cancel the timer select
‘CLEAR TIMER’.
6. For adjusting the ame intesity, select the
desired level on the left side of the screen.
(1-lowest, 6-highest)
Should there not be enough fuel for the select-
ed burning time - the replace will shut down
automatically.
Select ‘STOP’ to turn o󰀨 the replace.
2. In order to pair your replace with your
smart device, start the replace by pressing
the ‘ON’ button.
Start the App and choose your replace.
Insert the code from YOUR rating plate, like
the one highlighted above.
3. Once your device is paired, the replace
should be visible on the app. You are now
able to change the name of the replace.
Note: You are able to pair more than one re-
place like described in the step nr. 2 and give
them di󰀨erent names.
Installation of Decoame App to the Denver e-Ribbon Basic burner
Control Panel Flame level indicator
1-5 + ECO-Wave
Fuel level indicator
START/STOP the replace
Adjust the ame level up
Service USB
Step 1 Turn on the electronics of your Denver e-Ribbon Basic™ by pressing the button.
Step 2 Fill in the right amount of bioethanol in the fuel tank by verifying the level on the fuel level indicator.
Step 3 To ignition the replace. Press the button on the control panel.
After about 3 minutes, the rst ames will appear around the centre of the ame tray.
Step 4 When the lament is no longer red (approx. 10 min) it is possible to adjust the ames.
Step 5 To switch o󰀨 the re at any time – also during the warming-up phase – press the button on the
control panel. The ames will disappear within a few minutes.
On / Off
Adjust the ame level down
Fuel tank
Use the supplied remote
control or download the
Decoame App to your
mobile device for con-
trolling the bioreplace.
DENVER E-RIBBON BASIC BURNER
Filament
Operating: