ATWORK AW-50168N User manual

Identify all the components
Hardware identification
1. Cam lock
- 16pcs
2. Cam bolt
- 16pcs
3. Wood dowel
- 29pcs
6. Shelf support
- 4pcs
7. Handle
- 2pcs
8. Bolt
- 4pcs
9. Screw
- 2pcs
4. Screw
- 24pcs
5. Hinge
- 4pcs
ATWORK Wall storage cabinet
with frosted glass doors Model# AW-50168N
10. Adhesive cover
- 16pcs
11. Adjustable glide
- 4pcs
12. Stopper
- 6pcs
B. Left side - 1pc C. Right side - 1pc D. Shelf - 1pc
A. Top - 1pc
G. Bottom trim
- 2pcs
H. Back Panel
- 1pc
J. Door
- 2pcs
K. Adjustable Shelf
- 1pc
F. Top trim
- 1pc
E. Bottom - 1pc
I. Base Rail
- 2pcs
ABCDE
F
G
G
H
IJK
Back
Front
4
Step
Steps
Slide Back Panel (H) top down. Please
make sure that the panel is slid within the
2
Step
Attach the cam bolts (2) and wood dowels (3) panel (B)
as illustrated. Insert cam locks (1) into panel (D) & (E) with arrows
on cam locks facing the holes to the side of the panels.
Make sure panels (D) & (E) have cam locks facing down. Attach
the panels and secure the cam locks by turning clockwise.
Cover the cam locks with adhesive covers (10). Attach top trim (F)
to panel (B), make sure side with cam lock faces inward.
cam bolts (2) and the wood dowels (3)
reas illustrated.Then insert the
3
Step
Attach the
on panels ( C ) in the a
cam locks (1) into panels ( D ) and ( E ) with the arrows
on the cam locks facing the holes to the side of the
panels (D & E). Attach the panels and secure the cam
locks, turning clockwise to lock. Cover the cam locks
with the adhesive covers (10).
top
2
3
2
3
B
E
D
F
top
B
DE
F
2
3
2
310
1
C
top
H
B
C
Finished edge
I
I
E
Finished edge
Attached bottom trim back (G) to Bottom
board (E)
screws (9) supplied. Insert the wood dowels (3)
into the holes on the Bottom trim (G).
1
Step
and Base Rail (I) with wood dowel (3) and

I noitcurtsn
ylbmessA
Model# AW-50168 N
to the
re the hinge
oor up
nto
s. Secure
s (4). Attach the
7
Step
To install the hinge, attach the hinge
inside of the cabinet on the side panels
using the screws (4). Make su
is in the right direction. Hold the d
to the hinges, the hinges should slot i
the indentation on the door panel
the door panels with screw
door handles (7) with the supplied bolts (8).
Insert the shelf support (6) at the desired
height. To level the door panel, loosen 2
screws located on the hinge. Once desired
position is set, tighten the screws to secure.
ATWORK Wall storage cabinet w/ frosted glass doors
6
Step
To secure Back Panel (H), insert Stoppers (12)
as illustrated. Insert screw supplied into the
stopper and slowly tighthen it. Attach adjustable
glides (11) to the bottom of the cabinet.
Steps
5
Step
Attach the cam bolts (2) and the wood dowels
(3) on panels ( A ) and ( G ) & ( I ) in the areas illustrated.
Then insert the cam locks (1) into panels ( B ) and ( C )
with the arrows on the cam lock facing the holes
to the side of the panels. Attach the panels and
secure the cam locks, turning clockwise to lock.
Cover the cam locks with the Adhesive covers (10).
I
3 2
1
10
C
3
2
2
3
3
3