Noble House Home Furnishings Push Back Chair User manual

Assembly Instructions
Caution : You must read this before you proceed
Push Back Chair
Parts List
Label Picture Description QTY (pc)
A Chair Backrest 1
BChair Base With
Footrest 1
C Left Wing(C) 1
Noble house Home Furnishings LLC Page 1 of 10

D Right Wing(D) 1
EFront Leg with 1
Plastic Gasket 2
F
Hind Leg with 1
Silicone Gasket and
1 Plastic Gasket
2
Hardwares List
Label Picture Description QTY (pc)
Plastic Gasket 3
Noble house Home Furnishings LLC Page 2 of 10

Assembly Preparation
Before Beginning
Assembly:
Read instructions,cover to cover-
Have 2 adults on hand for assembly-
Do not assemble on flooring or carpet-
Assemble on a clean non-marring surface (packing foam)-
Save all packaging until finished-
Assembly Steps
Parts Introduction
This product has multiple parts and may require up to some 30 minutes to
assemble. To give you an overview of the product parts, the above picture is to
help you put the various parts into perspective. Please read through the
instructions below to familiarise yourself with the parts and steps before
assembly.
Front Facing
Chair Backrest(A)
Front Legs(E)
Chair Base WithFootrest(B)
Hind Leg(F)
Right Wing (c)
Left Wing(B)
Noble house Home Furnishings LLC Page 3 of 10

Step 1
Take out the Chairrest(A) from the Chair Base with Footrest(B).
Step 2
Place the Chair Base with Footrest(B) facedown on a clean,non-marring surface.
Open the non-woven bag and take out the Front Leg with 1 Plastic Gasket(E)，Hind Leg
with 1 Silicone Gasket and 1 Plastic Gasket(F) and Plastic Gaskets(①).
Step 3
Turn the Chair Base with Footrest(B) upside down on a clean, non-marring
surface.
Take out 2 non-woven bags with Wing inside from the bottom of the
mechanism. Then take out the Left Wing(C) and Right Wing(D) from non-woven
bags.
A
B
A
c
D
velcro
E
F
①
B
Noble house Home Furnishings LLC Page 4 of 10

Step 4
Install the Front Leg(E) and Hind Leg (F) at the bottom of the Chair by placing
one Plastic Gasket(①) on the threaded stem.
Then insert threaded stem into the mounting postion at the corner of the Chair.
Tighten by turning the Leg clockwise.Do not over tighten.
Repeat the same process to install the remaining two Legs.
Take care of the shape of the Legs and ensure they in the correct postions.
Note: The use of Gaskets are OPTIONALand are especially useful to help
alleviate slight wobbleness. Some Legs may need more than one gasket whilst
some Legs may not need any.
Step 5
With assistance from your adult partner, hold up the Chair Backrest(A).
while standing behind the Chair Base (B)
Insert the small metal arms on the sides of the Chair Backrest(A)into the
prefabricated slide lock gadget on the Chair Base with Footrest(B)as shown
above.
Firmly but gently, push the Chair Backrest(A)downwards until the Backrest is
fully slotted and locked into position.
F
A
Velcro
B
A
Legs: Bevelled plane inside facing
Velcro
B
F
E
A
A
B
E
Noble house Home Furnishings LLC Page 5 of 10

Step 6
Position the Chair Backrest(A) on it's left side.
Align the mounting brackets of the Left Wing(C) with those on the left side of
Chair Backrest(A)
Then slide Left Wing(C) forward by hand to make sure it locks into the position
as shown in the picture.
Step 7
Position the Chair Backrest(A) on it's right side.
Align the mounting brackets of the Left Wing(D) with those on the left side of
Chair Backrest(A)
Then slide Left Wing(D) forward by hand to make sure it locks into the position
as shown in the picture.
Step 8
Velcro
C
A
B
E
F
Noble house Home Furnishings LLC Page 6 of 10

Smooth down the fabric flap on the Chair Backrest(A).
Run your hands down both sides of the flap,from top to bottom,allowing the
velcro tape to adhere to the flap under the seat of the Chair.
Step 9
Make sure all parts are connected and securely locked into position.
your Chair is ready for use.
This Sofa can only be used on a flat, level surface.
Step 10
Push up the Right wing(D) and the Left wing(C) one by one until taken off from
the Chair Backrest(A).
Step 11
A
B
F
Velcro
E
C
D
Velcro
Test for stability
Noble house Home Furnishings LLC Page 7 of 10

Disassembly Note:open the flap on the Chair Backrest(A),use a
screwdriver(Don´t use fingers) pressing outward on the metal ear on the
preattached Metal Bracket on one side of the Chair Base(B),with assistance of
you adult partner to keep the Chair Base(B) in place,pull out the Chair
Backrest(A) upward at the same time,repeat the same step for another
side.Then the Chair Backrest(A) can be taken out.
User Instructions.
Push Back Chair
Please read the Instruction Manual below carefully before use.
Supervise children,when in use of this Push Back Chair.
Warning
Noble house Home Furnishings LLC Page 8 of 10

Do not allow children to play on the chair.
Always leave the chair in an upright and closed position after use!
Keep hands and feet clear of the footrest mechanism and ANY gaps.
Only the occupant should operate the chair.
To get into a open position-To push the Chair Backrest
Sit into the seat.
The Chair Backrest will fall down and footrest will open when push the Chair
Backrest by your back.So do must put your feet on footrest well when you push
down the Chair Backrest.Open the trigger on the outside of right armrest.
Use your body weight and push backwards into the seat into a fully reclined
position.
to get out of chair-move Seatback into Upright Position
Tilt your body weight slightly forward and upwards.
The seat back will come up to an upright position.
Use your feet to push the footrest down.
The Chair will automatically lock when it is in the fully upright position.
Where necessary,use your arms help lift/push yourself out of the seat
Noble house Home Furnishings LLC Page 9 of 10

Noble house Home Furnishings LLC Page 10 of 10