Noble House Home Furnishings SOFA User manual

Assembly Instructions
Caution: You should read this carefully before you proceed
SOFA
Noble House Home Furnishings LLC Page 1 OF 11

Label Picture Description QTY
A Backrest 1
B Seat Cushion 2
C Left Armrest 1
D Right Armrest 1
ESeat 1
Parts List
Noble House Home Furnishings LLC Page 2 OF 11

F Left Back Cushion 1
G Right Back Cushion 1
H Left Arm Cushion 1
I Right Arm Cushion 1
J Sofa Leg 4
K Middle Support Leg 1
Noble House Home Furnishings LLC Page 3 OF 11

Label Picture Description QTY
①Bolt (M8*70MM) 11
②Washer 11
③Gasket 6
④Allen Key 1
⑤Spring Washer 11
⑥Silicone Gasket 4
Before Beginning
Assembly:
Hardware
Assembly Preparation
X 6
X 11
X 11
X 11
X 4
Noble House Home Furnishings LLC Page 4 OF 11

Overview
Assembly Steps
This Sofa has multiple parts and may require up to 60 minutes to assemble. To give you an overview of
the Sofa parts, the above picture is provided to help you put the various parts into perspective. Please
read through the instructions below to familiarise yourself with the parts and steps before assembly.
Note: It is recommended that you have an adult partner to assist you during the entire assembly
process.
FRONT FACING
Left Armrest (C)
Right Armrest (D
)
Backrest (A)
Sofa Leg (J))
Sofa Leg (J)
Seat (E
)
Middle Support
Leg (K)
Left Back Cushion (F)
Right Back Cushion(G)
Right Arm Cushion (I)
Left Arm Cushion(H
)
Seat Cushion (B)
Noble House Home Furnishings LLC Page 5 OF 11

Step 1
Open the carton and place all the parts on a clean, non-marring surface.
With the assistance of your partner, attach the Seat(E) to the Armrest(C&D) with Bolts(①), Spring
Washers(⑤), and Washers(②) using the Allen Key(④) as pictured above.
Assistance from an adult partner is needed for this assembly process.
Tighten the Bolts fully in a sequential manner.
DO NOT fully tighten a Bolt in one go and then move on to the next.
Rather, In a sequential manner, gradually tighten each Bolt until all Bolts are evenly secured.
This methodology will ensure maximum evenness once all Bolts are fully tightened.
Caution: Ensure that your fingers do not get caught or pinched in the assembly process.
Seat (E)
Seat (E)
Right Armrest (D)
Left Armrest (C)
Noble House Home Furnishings LLC Page 6 OF 11

Step 2
With the assistance from your adult partner:
2.1)Lift the Backrest(A) up, make sure the Backrest(A) is vertical and aligned to the Seat and Armrests.
Align the Tapered Connectors on the Backrest(A) with those on the Armrest(C&D).
Your adult partner may need to push the Armrests inwards to the Backrest(A) to allow for better
alignment.
Slip and Slide the Backrest, in a gradual and balanced manner into the Tapered Connectors.
2.2) Push the Backrest(A) downwards until it is fully slotted and locked into position.
Note: Make sure the Tapered Connectors on the Backrest(A) lock into the Tapered Connectors on
the Armrest(C&D) .
Fully locked postion: Check and assess that the base of the Backrest(A) and Seat(E) are aligned
and level.
Assistance from an adult partner is needed for this assembly process.
Right Armrest (D)
Left Armrest (C)
Seat (E)
Backrest (A)
Tapered
Connectors
on Backrest
Tapered
Connectors
on Armrest
2.1
2.2
Noble House Home Furnishings LLC Page 7 OF 11

Tilt and lay the Sofa on its Backrest(A) onto a flat surface.
Attach the Seat(E) to the Backrest(A) with Bolts(①), Spring Washers(⑤), and Washers(②) using the
Allen Key(④) as pictured above.
Tighten the Bolts fully in a sequential manner.
DO NOT fully tighten a Bolt in one go and then move on to the next.
Rather, In a sequential manner, gradually tighten each Bolt until all Bolts are evenly secured.
This methodology will ensure maximum evenness once all Bolts are fully tightened.
Note: If you can not insert the Bolts into position, please back up to Step 2 to "push Backrest
downwards".
Step 3
Seat (E)
Noble House Home Furnishings LLC Page 8 OF 11

Install one of the Sofa Legs(J) into the Seat(E) by placing one Silicone Gasket (⑥) and one Gasket(③)
onto the threaded stem.
Insert the threaded stem of the Sofa Leg(J) into one of the mounting positions of the Seat(E), then
tighten by turning the Leg clockwise until it is completely secure.
Repeat the same step to install the remaining three Sofa Legs(J).
Install the Middle Support Leg (K) by placing one Gasket(③) on the threaded stem.
Note: The use of Silicone Gaskets (⑥) is to ensure you can turn the Sofa Leg (J) into the correct
position.
The use of Gaskets are OPTIONAL and are especially useful to help alleviate slight wobbles.
Some Legs may need more than one whilst some legs may not need any.
Please keep the Allen key in a safe place for future use. You may need to tighten the Bolts again
with the Allen key if the product loosens during use.
Step 4
Sofa Leg(J)
Gasket(③)
Silicon Gasket(⑥)
U
se Silicon Gasket(⑥and Gaskets (③
)
to achieve stability
Noble House Home Furnishings LLC Page 9 OF 11

Step 5
Place the sofa in an upright position, then place the Seat Cushions(B), the Back Cushions (F&G), and
the Arm Cushion (H&I) onto the Sofa as shown in the above picture.
Your Sofa is now ready for use.
This Sofa can only be used on a flat, level surface.
Left Back Cushion (F)
Right Back Cushion (G)
Left Arm Cushion(H)
Right Arm Cushion(I
)
Seat Cushion(B)
Noble House Home Furnishings LLC Page 10 OF 11

Noble House Home Furnishings LLC Page 11 OF 11