ATZ HDMI-V2-44HE70 User manual

Model : ATZ HDMI-V2-44HE70
Description : 4×4 Matrix Switch Over HDBaseT™ w 4x HDBaseT Receiver Box 70m,
4K60 4:2:0 HDMI2.0 HDCP2.2
pg. 1
Notes : - All brand names and trademarks are properties of their respective holders and are referred to here for descriptive purpose only. Photo attached is for reference only, it may be slightly varied in items of colour,
shape from the actual item delivered from time to time.
All specifications are subject to change without prior notice.
© Copyright A Z
This HDBaseT 4x4 HDMI Matrix with simultaneous CAT5e 6 7 and HDMI outputs
connects four HDMI sources to eight displays. This matrix features four HDMI outputs
and each HDMI output is mirrored to provide a CAT-Cable output which runs
simultaneously. It supports the transmission of video (resolutions up to 1080p Full HD
and 4Kx2K@30Hz) and supports high resolution digital audio formats such as LPCM
7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio. Connect a HD BaseT
Receiver to each of the CAT-Cable outputs to extend the HDMI signal up to 230ft 70m
(70m Version) or 131ft 40m(40m version)for multi-room connectivity. It works with
Blue-Ray players, Set-Top boxes, Home Theater PCs, and game consoles that connect to
an HDMI display. Any source is accessible at all times by any display by selecting it via
the supplied IR Remote Control, RS-232, TCP IP or by using the selection buttons on the
front panel. This device supports High Definition Audio, and 3D signal compatibility

Model : ATZ HDMI-V2-44HE70
Description : 4×4 Matrix Switch Over HDBaseT™ w 4x HDBaseT Receiver Box 70m,
4K60 4:2:0 HDMI2.0 HDCP2.2
pg. 2
Notes : - All brand names and trademarks are properties of their respective holders and are referred to here for descriptive purpose only. Photo attached is for reference only, it may be slightly varied in items of colour,
shape from the actual item delivered from time to time.
All specifications are subject to change without prior notice.
© Copyright A Z
Features:
•HDMI2.0, HDCP2.2 compliant.
•Support color space conversions among RGB, YCbCr 4:4:4, YCbCr 4:2:2 and xvYCC
video formats without deep color.
•Support video format up to 4k2k@30Hz with 24bit RGB YcbCR 4:4:4 YCBCR 4:2:2,and
up to 4k2k@60Hz with 12bit YCBCR 4:2:0.
•Support 3D frame sequential video format up to 1080p@60.
•Support high resolution VESA mode video format up to QSXGA@60Hz.
•Support reception of any audio data conforming to the HDMI specification such PCM up
to 192kHz, compressed audio(IEC 61937),DSD,DST,DTS and HBR.
•Support Transmission distance: Over CAT5e 6 7
- 70 meters: 1080P @60Hz@36bit; 3D1080P@30Hz36bit;
- 40 meters: 1080P @60Hz@48bit; 1080P @120Hz@24bit; 3D1080P@60Hz@36bit;
4K x 2K@30Hz@24bit.
•Support POE function. ※ See the description 1
•Support wideband IR(30-60Khz) matrix system, IR transport channel can be forward
or backward and supports GLOBAL IR. ※ See the description 2.
•Support RS-232 4 channel bypass. ※ See the description 3.
•Support simultaneous HDMI and CAT outputs
•Support RS-232, remote control, on-panel control and TCP IP Control
•Support smart EDID management
Specifications:
Technical
Video Bandwidth
297MHz[10.2Gbps]
Support Video Resolution
480i,576i,480p,576p,720p,1080i,1080p24 30 50 60.4Kx2
K@30;
Input Ports
4×HDMI, 5×IR Receiver, 1×RS
-
232, 1xRJ
-
45(Control),
4x
RS232
Output Ports
4×CAT5e 6 7, 4×IR Blaster, 4×HDMI
HDMI connector
Type A 19 pin female
RJ-45 connector WE SS 8P8C
3.5mm connector (TX and RX) IR Receiver IR Blaster

Model : ATZ HDMI-V2-44HE70
Description : 4×4 Matrix Switch Over HDBaseT™ w 4x HDBaseT Receiver Box 70m,
4K60 4:2:0 HDMI2.0 HDCP2.2
pg. 3
Notes : - All brand names and trademarks are properties of their respective holders and are referred to here for descriptive purpose only. Photo attached is for reference only, it may be slightly varied in items of colour,
shape from the actual item delivered from time to time.
All specifications are subject to change without prior notice.
© Copyright A Z
ESD Protection
Human
-
body Model: ± 8kV (Air
-
gap discharge)± 4kV
(Contact discharge)
Power Supply
AC
Power Supply
(US EU standards, CE FCC UL certified)
Dimensions
440 mm (W)×200 mm (D)×45 mm (H)
Weight
1820 g
Chassis Material Metal
Silkscreen Color Black
Operating Temperature 0 ºC~40 ºC 32 ºF~104 ºF
Storage Temperature −20 ºC~60 ºC
−4
ºF~140 ºF
Relative Humidity 20~90 % RH (non-condensing)
Power Consumption 50 W(max) 0.5w(Standby)
Pa nel Functions
Front Panel:
umber
ame
Function description
1 LCM Display the information of each input and output setting and
EDID management.
2
IR IR Receiver window (accepts the remote control signal of this
device only).
POWER
Press this button to power the device on off. The LED will
illuminate green when the power is on, red when it is in
'Standby' mode.

Model : ATZ HDMI-V2-44HE70
Description : 4×4 Matrix Switch Over HDBaseT™ w 4x HDBaseT Receiver Box 70m,
4K60 4:2:0 HDMI2.0 HDCP2.2
pg. 4
Notes : - All brand names and trademarks are properties of their respective holders and are referred to here for descriptive purpose only. Photo attached is for reference only, it may be slightly varied in items of colour,
shape from the actual item delivered from time to time.
All specifications are subject to change without prior notice.
© Copyright A Z
LOCK Press this button to lock all the buttons on the panel, press
again to unlock
3 OUTPUT INPUT
Press the OUTPUT and INPUT button to select the output
corresponding input.
For example: Press OUPUT ALL>INPUT 1, The OUTPUT
A,B,C,D will be set to INPUT 1.
Press PTP button, The OUTPUT A,B,C,D will corresponding
INPUT 1,2,3,4.
4 EDID
Smart EDID management, the LCM will display the EDID
operation.
Press the MENU button will enter the EDID management
window,
Press UP or DOWN button to select the needed EDID
setting,
Press ENTER button to select the download input source.
It can easy download any EDID mode to any input source.
ote: The EDID mode table
EDID
Mode
EDID Description
1
1080
p
, 2CH AUDIO
2
1080
p
, DOLBY DTS 5.1
3
1080
p
, HD AUDIO
4
1080
i
, 2CH AUDIO
5
1080
i
, DOLBY DTS 5.1
6
1080
i
, HD AUDIO
7
3D,1080p, 2CH AUDIO
8
3D, 1080p,DOLBY DTS 5.1

Model : ATZ HDMI-V2-44HE70
Description : 4×4 Matrix Switch Over HDBaseT™ w 4x HDBaseT Receiver Box 70m,
4K60 4:2:0 HDMI2.0 HDCP2.2
pg. 5
Notes : - All brand names and trademarks are properties of their respective holders and are referred to here for descriptive purpose only. Photo attached is for reference only, it may be slightly varied in items of colour,
shape from the actual item delivered from time to time.
All specifications are subject to change without prior notice.
© Copyright A Z
9
3D,1080p, HD AUDIO
10
4
K x
2
K@30Hz
, 2CH AUDIO
11
4
K x
2
K@30Hz
, DOLBY DTS 5.1
12
4
K x
2
K@30Hz
, HD AUDIO
13
4
K x
2
K@60Hz
, 2CH AUDIO
14
4
K x
2
K@60Hz
, DOLBY DTS 5.1
15
4
K x
2
K@60Hz
, HD AUDIO
16
Copy from HDMI OUTPUT A
17
Copy from HDMI OUTPUT B
18
Copy from HDMI OUTPUT C
19
Copy from HDMI OUTPUT D
20
Copy from HDB OU PU A
21 Copy from HDB OU PU B
22
Copy from HDB OU PU C
23 Copy from HDB OU PU D
EDID. What is it and what is it used for?
Under normal circumstances, a source device (digital and analog) will require information about
a connected device display to assess what resolutions and features are available. The source can
then cater its output to send only resolutions and features that are compatible with the attached
device display. This information is called EDID (Extended Display Information Data) and a
source device can only accept and read one EDID from a connected device display. Likewise, the
source an only output one resolution for use by a connected device display.
Why is EDID so important with the HDMI Matrix?
The Matrix is complex piece of technology that replicates and switches between multiple inputs
and outputs. Each connected source device will require one EDID to read. EDID management is
carefully handled by HDMI Matrix to provide a single EDID for each source to read.

Model : ATZ HDMI-V2-44HE70
Description : 4×4 Matrix Switch Over HDBaseT™ w 4x HDBaseT Receiver Box 70m,
4K60 4:2:0 HDMI2.0 HDCP2.2
pg. 6
Notes : - All brand names and trademarks are properties of their respective holders and are referred to here for descriptive purpose only. Photo attached is for reference only, it may be slightly varied in items of colour,
shape from the actual item delivered from time to time.
All specifications are subject to change without prior notice.
© Copyright A Z
What options do I have to manage the EDID in the HDMI Matrix?
First, it is important to note that each source device can only output one video audio signal type.
This includes resolutions and timings. When multiple devices displays are used, such as with the
HDMI Matrix, it is important to use devices displays that have similar or compatible
resolutions features. This will ensure that the single video audio signal produced by the source
device is accepted by all of the connected output devices displays. The user has the option,
through the EDID management window, to choose how the unit will manage the EDID from
multiple HDMI devices displays. Therefore the user has some control over the
resolutions features that the source devices will output. The HDMI Matrix has a multiple EDID
management modes that will control how the EDID information from multiple devices displays
are combined, ignored, and routed.
Rear panel:
umber ame Function description
1 GND Connect the Housing to ground.
2 IR Matrix
IR EXT
: if the panel sensor is obstructed or the unit is
installed in a closed area out of infrared line of sight, the IR
RX receiver included can be inserted into the HUB IR port at
the rear to extend the IR sensor range and enable local
control of the matrix.
IR I /OUT: Super IR control system interface. For further
details, please refer to the Super IR system control
introduction.
3 PC CONTROL
TCP IP: This port is the link for TCP IP control, connect to an
active Ethernet link with an RJ45 terminated cable.
RS-232: Connect to a PC or control system with D-Sub 9-pin
cable for the transmission of RS-232 commands.
4 HDMI INPUT Connect to the HDMI input source devices such as a DVD
player or a Set-top Box with HDMI cable.
5
HDMI
The HDMI OUTPUT connect to HDMI equipped TVs or monitors

Model : ATZ HDMI-V2-44HE70
Description : 4×4 Matrix Switch Over HDBaseT™ w 4x HDBaseT Receiver Box 70m,
4K60 4:2:0 HDMI2.0 HDCP2.2
pg. 7
Notes : - All brand names and trademarks are properties of their respective holders and are referred to here for descriptive purpose only. Photo attached is for reference only, it may be slightly varied in items of colour,
shape from the actual item delivered from time to time.
All specifications are subject to change without prior notice.
© Copyright A Z
OUTPUT
and the HDBT OUTPUT connect to the HDBT Receiver. The
coaxial and analog audio output connect to the audio
amplifier. The TX and RX for RS-232 communication with the
HDBT Receiver TX and RX.
6
AC
POWER
INPUT
Connect to AC power with AC power cable.
Remote Control
1. Press the button to power on the matrix or set it to standby mode.
2. Press the button to select output A for input 1,2,3 or 4 port.
Press this button to select the previous input port and to
select the next input port.

Model : ATZ HDMI-V2-44HE70
Description : 4×4 Matrix Switch Over HDBaseT™ w 4x HDBaseT Receiver Box 70m,
4K60 4:2:0 HDMI2.0 HDCP2.2
pg. 8
Notes : - All brand names and trademarks are properties of their respective holders and are referred to here for descriptive purpose only. Photo attached is for reference only, it may be slightly varied in items of colour,
shape from the actual item delivered from time to time.
All specifications are subject to change without prior notice.
© Copyright A Z
IR Control system (IR Call-back of Matrix and Source Devices)
The matrix is not only a switcher and extender of multiple HDMI
signals to multiple HDMI receivers located remotely, it also
passes IR control signals through the IR call-back system to the
matrix and HDMI sources for full, independent control of all
connected inputs from output locations.
Two-way IR Call-back between matrix, Sources and Displays from
Multiple Locations
A key feature on the matrix is discrete IR control of the matrix,
sources and displays from any location – so inputs at the matrix
end can be controlled at a display location and displays can be
controlled at the matrix location. This is accomplished by placing
a series of IR Emitters on devices to control and IR Receivers at
all locations you wish to control from to enable the IR signal to
travel both ways via the single Cat5e 6 7 cable.
01. At Matrix end: Insert the 3.5mm jacks of the IR TX Emitters included with the unit into the
IR TX Emitter ports at the rear of the matrix according to input. The IR signal is added to the
HDMI of the input device, for example, if the user is watching Blue-ray on input 1, the IR signal
will be directed through the IR TX1 socket to control the device.
As each IR TX port is allocated to an individual HDMI input port, if the user is unable to establish
IR control of the device, care should be taken to check firstly, that the IR emitter and HDMI
input ports match (Input 1-TX1, Input2-TX2 etc.) with plugs secured in correct ports, and
secondly, that the IR TX emitter sensors are firmly attached directly to the front of inputs and
covering infrared sensor windows of the source devices. Some later adjustment may be needed
to the location of the sensor to achieve the best performance results - sometimes moving the
sensor to different areas on the source can improve IR performance.

Model : ATZ HDMI-V2-44HE70
Description : 4×4 Matrix Switch Over HDBaseT™ w 4x HDBaseT Receiver Box 70m,
4K60 4:2:0 HDMI2.0 HDCP2.2
pg. 9
Notes : - All brand names and trademarks are properties of their respective holders and are referred to here for descriptive purpose only. Photo attached is for reference only, it may be slightly varied in items of colour,
shape from the actual item delivered from time to time.
All specifications are subject to change without prior notice.
© Copyright A Z
NOTE: Infrared receiving areas of devices can be located by shining a flashlight onto the front of
the device – the sensor should be able to be seen through the plastic as a small, round object
inside. Insert 3.5mm jacks of IR RX receivers into RX ports, making sure the receivers
themselves are placed in clear view to receive an infrared signal from the remote handset used
to control the display outputs.
02. At display end: Insert the IR RX Receiver jack into the IR RX port of the display receiver
balun, with the receivers themselves placed in clear view on or near the displays to receive an
infrared signal from the remote handset used to control inputs. Insert the IR TX Emitter jack into
the IR TX port of the display receiver balun, ensuring that the emitter sensor is securely
attached to infrared sensor window of the display. Follow the same connection and positioning
for all baluns displays connected to the matrix. If all IR TX Emitters and IR RX Receivers are
positioned and connected correctly with sources, displays and display receivers fully powered
and the matrix set to IR call-back enabled and IR TX Switch mode activated, two-way IR will
now be possible.
Note: Misplaced or poorly secured IR Emitters and Receivers may result in intermittent IR
control signals passed to and from the matrix. Check your placement and adjust if necessary.
IR BLASTER (TX)
To control the source: Plug IR Blaster into IR OUT port of transmitter unit; place blaster in front
of the IR eye of the source.
To control the display: Plug IR Blaster into IR OUT port of receiver unit; place blaster in front of
the IR eye of the display.
IR RECEIVER (RX)
To control the source: Plug IR Receiver into IR IN port of receiver unit; place receiver at or near
display.
To control the display: Plug IR Receiver into IR IN port of transmitter unit; place receiver in
position where it is able to receive remote signals.

Model : ATZ HDMI-V2-44HE70
Description : 4×4 Matrix Switch Over HDBaseT™ w 4x HDBaseT Receiver Box 70m,
4K60 4:2:0 HDMI2.0 HDCP2.2
pg. 10
Notes : - All brand names and trademarks are properties of their respective holders and are referred to here for descriptive purpose only. Photo attached is for reference only, it may be slightly varied in items of colour,
shape from the actual item delivered from time to time.
All specifications are subject to change without prior notice.
© Copyright A Z

Model : ATZ HDMI-V2-44HE70
Description : 4×4 Matrix Switch Over HDBaseT™ w 4x HDBaseT Receiver Box 70m,
4K60 4:2:0 HDMI2.0 HDCP2.2
pg. 11
Notes : - All brand names and trademarks are properties of their respective holders and are referred to here for descriptive purpose only. Photo attached is for reference only, it may be slightly varied in items of colour,
shape from the actual item delivered from time to time.
All specifications are subject to change without prior notice.
© Copyright A Z
HDBT Receiver
Number Name Function description
1 POWER This LED illuminates when the device is connected with
power supply
2 DC 24V Plug the 24V DC power supply into the unit.
3 HDBaseT In Standard HD BaseT signal input port. Connect HD BaseT
transmitter with a UTP cable.
4
HDMI Out
HDMI output port.
This slot is where you connect the HDTV
or monitor with HDMI cable.
5
IR In
Channel 1 IR
Receiver
.
Connect with Wideband IR Rx.
6
IR Out
Channel 2 IR
Transmitter
.
Connect with Wideband IR Tx.
7
RS-232
Phoenix jack provide Serial port control
signal from receiver
or to receiver.
8
Connection
Signal Indicator
Lamp
※ Illuminate: The Transmitter and Receiver are in good
connection status.
※ Flashing: The Transmitter and Receiver are in
poor connection status.
※ Dark: The Transmitter and Receiver are not connected.
9 Data Signal
Indicator Lamp
※ Illuminate: The HDMI signal with HDCP.
※ Flashing: The HDMI signal without HDCP.

Model : ATZ HDMI-V2-44HE70
Description : 4×4 Matrix Switch Over HDBaseT™ w 4x HDBaseT Receiver Box 70m,
4K60 4:2:0 HDMI2.0 HDCP2.2
pg. 12
Notes : - All brand names and trademarks are properties of their respective holders and are referred to here for descriptive purpose only. Photo attached is for reference only, it may be slightly varied in items of colour,
shape from the actual item delivered from time to time.
All specifications are subject to change without prior notice.
© Copyright A Z
※ Dark: No HDMI signal.
※ Description 1
POE(Power Over Ethernet) Application Example:
This system can run by only the matrix(TX) is powered, RXs do not need powered.

Model : ATZ HDMI-V2-44HE70
Description : 4×4 Matrix Switch Over HDBaseT™ w 4x HDBaseT Receiver Box 70m,
4K60 4:2:0 HDMI2.0 HDCP2.2
pg. 13
Notes : - All brand names and trademarks are properties of their respective holders and are referred to here for descriptive purpose only. Photo attached is for reference only, it may be slightly varied in items of colour,
shape from the actual item delivered from time to time.
All specifications are subject to change without prior notice.
© Copyright A Z
※ Description 2
GLOBAL IR control Application Example:
TV remote can control all TV at the same time.
All DVD remotes can control DVD, but not at the same time.

Model : ATZ HDMI-V2-44HE70
Description : 4×4 Matrix Switch Over HDBaseT™ w 4x HDBaseT Receiver Box 70m,
4K60 4:2:0 HDMI2.0 HDCP2.2
pg. 14
Notes : - All brand names and trademarks are properties of their respective holders and are referred to here for descriptive purpose only. Photo attached is for reference only, it may be slightly varied in items of colour,
shape from the actual item delivered from time to time.
All specifications are subject to change without prior notice.
© Copyright A Z
※ Description 3
Bidirectional RS-232 control Application Example:
This system provides 4 channel RS-232.

Model : ATZ HDMI-V2-44HE70
Description : 4×4 Matrix Switch Over HDBaseT™ w 4x HDBaseT Receiver Box 70m,
4K60 4:2:0 HDMI2.0 HDCP2.2
pg. 15
Notes : - All brand names and trademarks are properties of their respective holders and are referred to here for descriptive purpose only. Photo attached is for reference only, it may be slightly varied in items of colour,
shape from the actual item delivered from time to time.
All specifications are subject to change without prior notice.
© Copyright A Z
Operate and Connect
1 . Connect up to 4 sources such as a Blue-Ray Player, game console, A V Receiver, Cable or
Satellite Receiver, etc. to the HDMI inputs on the unit. Do not hot plug! Insert and extract
cables carefully with the power switch off. Connecting and disconnecting while the unit is
powered can result in damage to circuitry.
2. Connect the output HDBT ports and or HDMI output ports, starting with output 1, to the

Model : ATZ HDMI-V2-44HE70
Description : 4×4 Matrix Switch Over HDBaseT™ w 4x HDBaseT Receiver Box 70m,
4K60 4:2:0 HDMI2.0 HDCP2.2
pg. 16
Notes : - All brand names and trademarks are properties of their respective holders and are referred to here for descriptive purpose only. Photo attached is for reference only, it may be slightly varied in items of colour,
shape from the actual item delivered from time to time.
All specifications are subject to change without prior notice.
© Copyright A Z
HDBT Receiver display receivers (sold separately) (using well terminated or pre-terminated
Cat5e 6 7 cables no longer than 230 ft 70M)
3. If utilizing UTP, connect the output HDMI ports of the HDBT Receiver display receivers (sold
separately) to high-definition displays such as an HDTV or HD projector that use HDMI
inputs. Note that high-speed HDMI cables are recommended for the distances that are
required for each connection.
4. Plug in IR transmitters to the back of the Matrix Selector Switcher unit (IR TX), the
transmitters are labeled IR TX, place in front of the IR receiver of the source, ensure that
each emitter is placed in front of the IR receiver eye. Double-sided adhesive tape provided.
5. Plug in IR receivers to the port of the HDBT Receiver display receivers (sold separately) ,the
receivers are labeled IR RX, use provided double-sided adhesive tape to stick emitters at
each display at a desired place that will receive a remote signal.
6. For power, plug in the source first, followed by the Matrix (power supply included), followed
by the display receivers, followed by each output connected.
7. Power on each device in the same sequence.
Package contents:
1x HD BaseT 4x4 HDMI Matrix
4x HD BaseT Receiver
1x AC power cable
1x Operation Manual
5x Wideband IR Tx cable
6x Wideband IR Rx cable
1x HDMI Matrix IR Remote
1x Mounting ears(Matrix)
2x Mounting ears(Receiver)
1x RS-232 cable
Warranty: 2 Years
Warranty is effective from the date of original delivery.
This warranty shall be void if a serial number has been removed from the product.