AUDAC MBK1 V Series User manual

Installation manual
MBK1xxV
Step 1:
The pole ange adapter in
the bottom of the speaker
has to be replaced with a
screw ange adapter. This
is included with the optional
brackets. Attach with the
M6 screws.
Step 3:
Insert the large (M10) bolts
into the center threaded
holes (top and bottom).
These should stay up just
high enough so that the
intended slot in the bracket
can be hooked in.
Put the speaker in the
correct position and
tighten both M10 bolts.
Attach the drop safety wire
to one of the M10 ying
points. The other end of
the wire is attached to a
separate mounting point
on the wall.
Step 2:
Mount the U-bracket at a
designated location on the
wall or ceiling.
The screws are inserted
into the holes provided
on the bracket. Use the
correct fasteners for the
surface on which the
bracket is to be mounted.
Step 4:
Add the additional (small)
safety/ positioning bolts.
This is placed in the
rotation slot of the bracket.
Place the VEXO1xx in
your desired pitch angle
(-90° - 35°) and tighten the
bolts.
The MBK1xxV mounting bracket is specially designed for mounting the VEXO series speakers. These optional clever U-brackets
allow the easy installation of the VEXO series both horizontally and vertically, thanks to a provided slot the VEXO series speaker will
glide easily and safely into the bracket making installation a piece of cake.
MBK1xxV installation guide1
Caution: choose fasteners
that are consistent with
all local build codes and
requirement to support the
weight of the loudspeaker.
Included hardware:
Installation:
Drop safety wire
x2
M10 screws with
washers
x2
M6 screws with
washers
x2
Rubber washer
U-bracket M10 ange for bottom

MBK1xxV installation guide2
Dimensions:
REQUIREMENTS REGARDING INSTALLATION, SUSPENSION
AND CONNECTION OF THIS LOUDSPEAKER. EVEN WHEN
OTHERWISE SPECIFIED IN THIS DOCUMENT.
• IT’S THE INSTALLERS RESPONSIBILITY TO ENSURE
INSTALLATION OF THE LOUDSPEAKERS AND MOUNTING
SYSTEMS IS PERFORMED IN ACCORDANCE WITH ALL
APPLICABLE CODES
• UNSAFE MOUNTING OR OVERHEAD SUSPENSION ON ANY
HEAVY LOAD CAN RESULT IN SERIOUS INJURY OR DEATH, AND
PROPERT Y DAMAGE. IT’S THE INSTALLERS RESPONSIBILITY TO
EVALUATE THE RELIABILITY OF ANY MOUNTING METHOD USED
FOR THEIR APPLICATIONS
• THE INSTALLATION OF THIS LOUDSPEAKER SHALL BE DONE
BY QUALIFIED PERSONNEL ONLY.
• KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE. NEVER
THROW THEM AWAY
• ALWAYS HANDLE THIS UNIT WITH CARE
• CLEAN ONLY WITH DRY CLOTH
• HEED ALL WARNINGS AND FOLLOW ALL INSTRUCTIONS
• NEVER EXPOSE THIS EQUIPMENT TO RAIN, MOISTURE, ANY
DRIPPING OR SPLASHING LIQUID.
• DO NOT PLACE THIS UNIT IN ENVIRONMENTS WITH A HIGH
LEVEL OF DUST, HEAT, MOISTURE OR VIBRATION
• DO NOT USE HYDROCARBON BASED SOLVENTS, LUBRICANTS
OR CLEANING AGENTS OF ANY TYPE ON OR AROUND
THE DEVICE AND MOUNTING HARDWARE DURING THE
INSTALLATION. THE USE OF THESE PRODUCTS ON OR
AROUND THE MOUNTING ANCHORS AND SCREWS CAN
LEAD TO DEGRADATION OF THE PLASTIC MATERIAL, POSSIBLY
RESULTING IN CRACKING AND PREMATURE FAILURE OF THE
PR ODUCT.
• THIS UNIT IS DEVELOPED FOR INDOOR USE ONLY. DO NOT
USE IT OUTDOORS
• ONLY USE ATTACHMENTS & ACCESSORIES SPECIFIED BY THE
MANUFACTURER.
• ONLY INSTALL THE SPEAKER IN LOCATIONS THAT CAN
STRUCTURALLY SUPPORT THE WEIGHT OF THE SPEAKER.
IGNORING THIS CAN BRING THE SPEAKER DOWN.
• DO NOT USE ANY OTHER METHOD THAN SPECIFIED TO
MOUNT THE SPEAKER. IF EXTREME FORCE IS APPLIED TO THE
SPEAKER, IT COULD FALL DOWN
• ATTACH A SAFETY WIRE TO THE SPEAKER WHEN IT IS MOUNTED
HIGH UP. ONLY USE INDUSTRY-ACCEPTED RIGGING TOOLS AND
METHODS
• CAREFULLY CHECK THE UNIT’S CONDITION AFTER UNPACKING.
• IF THERE IS ANY DAMAGE TO THE CARTON BOX OR THE UNIT
ITSELF, INFORM YOUR VENDOR IMMEDIATELY.
• ALWAYS FOLLOW THE LOCAL REGULATIONS AND
PRECAUTIONS
This product contains no user serviceable parts. Refer all
servicing to qualied service personnel. Do not perform any
servicing (unless you are qualied to do so).
CAUTION - SERVICING
This product conforms to all the essential requirements and
further relevant specications described in following directives:
2011/65/EU (RoHS2) and 1907/2006 (REACH)
EC DECLARATION OF CONFORMITY
• DO NOT MAKE UNAUTHORIZED ALTERATIONS TO THE
PRODUCT.
• The MBK110V mounting bracket is for the use with VEXO110(A)
only.
• The MBK112V mounting bracket is for the use with VEXO112(A)
only.
• The MBK115V mounting bracket is for the use with VEXO115(A)
only .
BC
AA
A
D
E
FG
H
MBK110V MBK112V MBK115V
A566 mm 636 mm 716 mm
B83.5 mm 81mm 75 mm
C345 mm 390 mm 450 mm
D330 mm 370 mm 428 mm
E566 mm 636 mm 716 mm
F125 mm 140 mm 160 mm
G30 mm 35 mm 35 mm
H90 mm 90 mm 100 mm