Audio Control ACX-BT1 User manual
BLUETOOTH RECEIVER WITH APTX™ HD SUPPORT
Quick Start Guide
Features
• Compact, elegant design with no buttons or switches
• aptX™ HD Support
• BT v4.1 chip set
• All-weather IPX5 rated
• Universal design works with any amplifier or device with line
level (RCA) inputs
• Unique remote turn-on output circuit
• Pacific Northwest freshness built-in!
2
Quick Start Guide
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not submerge this apparatus in water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as mufflers, silencers, exhaust
pipes, or other apparatus (including amplifiers) that produce heat.
9. WARNING: Improper installation may lead to permanent injury or death.
Installation of the apparatus must be done with great care by qualified
personnel, to prevent damage to fuel lines, power and other electrical
wiring, hydraulic brake lines, and other systems, that might compromise
vehicle safety.
10. Provide +12v and ground wiring of sufficient size to ensure adequate
current to the receiver. For the ACX-BT1, this means 16-22 gauge wire.
11. Use rubber grommets to protect wiring whenever passing wires through
metal openings or bulkheads.
12. Only use attachments/accessories specified by the manufacturer.
13. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as the power in-
put terminals are damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
14. Fuses shall be replaced only with the correct type and fuse value, and
only when the apparatus is powered off.
15. Exposure to high sound pressure levels may lead to permanent hearing
loss. Take every precaution to protect your hearing.
The lightning flash with arrowhead symbol within an equilateral
triangle is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure, that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to
alert the user of the presence of important operating and mainte-
nance (servicing) instructions in the literature accompanying the
appliance.
Caution: to reduce the risk of electric shock, do not disassemble the appara-
tus, other than to remove the top panel to access the controls. There are no
user-serviceable parts inside. Refer servicing to
qualified personnel.
Recycling notice: If the time comes and this
apparatus has fulfilled its destiny, do not
throw it out into the trash. It has to be
carefully recycled for the good of mankind, by a facility specially
equipped for the safe recycling of electronic apparatii. Please con-
tact your local or state recycling leaders for assistance in locating
a suitable nearby recycling facility. Or, contact us and we might be
able to repair it for you.
3
1. Remote Turn-On Output (Blue) – This 12v DC/20mA remote
output is designed to turn on a connected amplifier. This output
is only active after audio has begun playing and will remain active
for approximately 7 seconds after audio playback has ceased.
2. 12 Volt Power Input (Fused @ 2A) (Red) – Connect this lead
to an accessory (switched) power source from your vehicle. If
no switched power source is available, a rocker or toggle switch
could also be used to turn the unit on/off.
Note: Depending on the vehicle type and application, you may wish
to connect this lead to a constant 12V power source instead. Be aware
that if the unit is connected in this manner that there will be a small
amount of constant current drawn from the connected power source.
3. Ground Input (Black) – Connect this lead to a solid ground con-
nection from your vehicle.
4. Left RCA line level output (Gray) – This RCA lead connects to the
LEFT low-level input of your amplifier or source unit.
5. Right RCA line level output (Blue) – This RCA lead connects to
the RIGHT low-level input of your amplifier or source unit.
Remote, Power, and Output Connections
q
w
e
r
t
4
Quick Start
Here are a few general steps to get your ACX-BT1 Bluetooth
Receiver up and running:
1. Undo the +12V and Ground connections to the vehicle battery
before making any connections to the Bluetooth receiver.
2. Pick a mounting location that will provide access to the controls
and connections, provide plenty of good ventilation, and also
protect the Bluetooth receiver from heat, moisture, and dirt.
3. The ACX-BT1 can be securely mounted using the two mounting
holes located in each side.
4. Before drilling any holes, take every precaution to prevent any
damage to fuel lines, power and other electrical wiring, hydraulic
brake lines, and other systems, that might compromise vehicle
safety.
5. When making connections, designate red RCA plugs as right
(the ACX-BT1 uses a blue connector for the right channel), and
designate white, black, or gray plugs as left. This is a good idea
for all signal connections made in your audio system. The key is
consistency. Stick with the same color coding and you’ll reduce
possible problems.
6. Use quality interconnect cables.
7. Connect the +12V input terminal of the unit to an accessory
(switched) power source from your vehicle. Use 16-22 gauge
wire. Connect the Ground terminal of the unit to a solid ground
connection from your vehicle using the same wire gauge as the
+12V power wire.
8. Connect the audio outputs of the unit to a signal processor or
amplifier.
Bluetooth Pairing and Streaming:
1. After the ACX-BT1 is powered up, you will see a small blue LED
flashing quickly from within the unit.
2. Open the Bluetooth settings or connections on your mobile
device.
3. Find the device called “AudioControl BT1”and tap or click on it to
pair your device.
4. Once paired, the blue LED will illuminate continuously.
5. Open your favorite music application and hit play on your favorite
jam.
6. Once music (or any sound) is playing, the red LED will shine forth
from within the ACX-BT1.
7. Enjoy your new Bluetooth streaming device and the sonic bliss
you’re about to experience.
8. Enjoy the drive!
5
System #1: Head-unit-less All-Weather System
L
Line-level L/R outputs
R
+
+
+
+
Quick Start Guide PN 915-027-0 Rev A
Specifications
All specifications are measured at 14.4 VDC (standard automotive voltage). As technology advances, AudioControl reserves the right to continuously
change our specifications, like our Pacific Northwest weather, although we are working on changing that as well.
ACX-BT1 Bluetooth Receiver
Nominal Output Level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.5 Vrms
S/N Ratio ....................................................95 dBa
Maximum Data Rate ....... 10+ meters (depending on environment)
Current Draw .................................................35 mA
Recommended Power / Ground Wire Gauge ............16-22 Gauge
Fuse Rating ......................................................2 A
Weight ......................................................0.2 lbs.
Dimensions.................................... 2.0"L X 2.5"W X 0.7"H
©2021 AudioControl. All rights reserved.
Warranty
For details of the limited warranty for your ACX-BT1, please visit the following
page on our website: http://www.audiocontrol.com/warranty
Please keep your receipt in a safe place.
AudioControl, Inc.
22410 70th Avenue West
Mountlake Terrace, WA 98043 USA
Phone 425-775-8461
email: sound.great@audiocontrol.com
Table of contents
Other Audio Control Receiver manuals
