Oceaneering C-Nav5000 User manual

C-Nav5000 Quick Start Guide
Follow this Quick Start Guide to enable the robust functionality of
the C-Nav5000.
Your C-Nav5000 has already been tested by qualified
C-Nav Technicians. Refer to the following steps to
connect equipment and operate the receiver.
This Quick Start Guide is intended to familiarize the user with
the basic setup of the C-Nav5000 only. The supplied USB
Flash Drive (P/N CNV7CNG002-0) includes the C-Nav5000
User Guide, (Adobe Reader required), which contains in-depth
product information and technical specifications. Refer to the
table below for items included in the C-Nav5000 GNSS
Sensor Kit.
Table 1: Supplied Equipment
C-Nav5000 GNSS Sensor
(P/N CNV5K-PH90229916)
COM1 –LAN Ethernet Data Cable (P/N CNV5K-
PH96235870)
HDD –26 to USB1 device/COM2/4 Serial Cable (P/N
CNV5K-96229301)
Unterminated Ext Power/1PPS/Event with Filter (P/N
CNV5K-PH96235771)
USB Flash Drive (P/N CNV7CNG002-0)
Dual Data Adapter (P/N CNVCNV335G001-0)
110/220 VAC Power Adapter (P/N CNV5K-
PH96235770)
Harns Power Cord 2-Prong North America (P/N CNV73-
200002-00LF)
Cord, Power, IEC320-C7 (EURO) (P/N CNV4250012-
220)
Cord, Power, IEC320-C7 (UK) (P/N CNV4250013-240)
1PPS Adapter/DB9-BNC (P/N CNVCNV335G002-0)
Mounting Bracket, Top & Bottom (P/N CNV5K-
PH60229636)
Phenolic Washer Kit (P/N CNV5K-PH95232908)
Very Important
Before connecting your C-Nav5000 ensure that the
unit has been isolated using the Phenolic Washer Kit.
This hardware enables the receiver chassis to be
electrically isolated from the mounting surface.
Refer to Section 4 –Installation of the C-Nav5000
User Guide for detailed information.
Connect Equipment
Figure 1: C-Nav5000 Rear View
Refer to Figure 1 above for the steps below:
1. Use one of the two supplied data cables for
communications:
Ethernet RJ45 / DB9S female Y-cable (P/N
CNV5K-PH96235870): Connect the Positronic 9-
Pin connector of the cable to COM1 - LAN at the
rear of C-Nav5000. Connect the DB9S end to the
computer or C-NaviGator CDU.
Or…
HDD –26 to USB1 Device/COM2/4 Serial Cable
(P/N CNV5K-96229301): Connect the 26 pin
connector of the cable to COM2/4 –USB1/2 at the
rear of C-Nav5000. Connect the DB9-1/2S end to
the computer or C-NaviGator CDU.
2. Mount the GNSS antenna. Locate the antenna in an area
with a 360clear view of the sky. Refer to Section 4 -
Installation of the C-Nav5000 User Guide for detailed
installation instructions.
3. Connect the TNC connector on one end of a C-Nav
approved GNSS antenna cable to the GNSS antenna.
Connect the other end of the cable to the TNC connector,
labeled GNSS1,at the rear of the C-Nav5000.
Optional C-Nav approved Antenna Cables are available
through your authorized C-Nav Dealer, or by contacting
C-Nav Support.
4. Perform one of these steps to setup power:
a. If you are connecting using the optional Positronic
9-Pin Female Unterminated Power Cable (P/N
CNV5K-PH96235771), connect the power cable to
the connector labeled PWR-1PPS, at the rear of
the C-Nav5000. Connect the unterminated end of
the power cable to a DC power source (9 to
32VDC, 6W typical, see Section 3 –Interfacing of
the C-Nav5000 User Guide for power cable pin
assignments).
b. If you are connecting using the optional AC Power
Supply Kit (P/N CNV5K-PH96235770), connect
the Positronic 9-Pin Female connector of the
Power Supply Unit to the connector labeled PWR-
1PPS, at the rear of the C-Nav5000. Insert an AC
Power Cord into the 2-prong receptacle on the
PSU, based on regional AC power availability
(110, 220 or 240 VAC power cords provided) and
plug into an appropriately rated wall receptacle.
5. To power the unit ON / OFF, depress the I/O switch
for more than 2 seconds. All front panel LEDs illuminate
for 3- 5 seconds during power-up as the receiver performs
its built-in-test. The Power / GNSS Status LED changes
to Red. Refer to Section 3 - Interfacing of the C-Nav5000
User Guide for LED status.
Figure 2: C-Nav5000 LED Indicator Panel
6. Your C-Nav5000 hardware is now properly connected.
7. At this point you may connect to C-Nav’s C-Setup,
C-Monitor®, C-Scape or C-NaviGator controller solutions
to view real-time positioning data and to control the C-
Nav5000.
The C-Nav Corrections Service license is not a
standard feature of any Software Bundle. It is
purchased separately. Refer to reverse side of this
pamphlet for more information on obtaining a C-Nav
license.

C-Nav5000 Quick Start Guide
How to Obtain a C-Nav License
The C-Nav Corrections Service is a subscription service. The
user pays a subscription fee, which licenses the use of the
service for a predetermined period of time. Subscriptions are
requested by completing the online request format: C-Nav
Authorization Portal,via a C-Nav authorized representative, or
by contacting C-Nav at: [e-mail]
C-Nav recommends that customers process new C-Nav license
requests 15 to 30 days before the expiration of the current
license.
The requirements to obtain a C-Nav license are:
Valid Purchase Order
Signed License Agreement
Appropriate Credit Terms with Oceaneering, Inc.,
or an Authorized Dealer; including a valid P.O
When contacting C-Nav regarding subscription or deactivation
of service, please provide the following information:
Vessel Info and brief project description (Name /
Number, Location)
Customer Info (Company Name, PO/Ref. Num.
Point of Contact)
C-Nav Equipment Details (Receiver Type,
Firmware version, Serial Number, P/N’s, etc)
Required Start / Stop Date or Period
Service Type (Land or Offshore, Activation or
Deactivation)
Operational Region (Asia, Australia, China, South
and Central America, Caribbean, Africa, Middle
East, or Other)
Detailed Contact Information (Phone, Fax, E-Mail,
Billing / Shipping Addresses)
An authorized subscription will provide an encrypted code,
which is specific to the Serial Number of the C-Nav receiver to
be authorized. This is entered into the receiver Over-the-Air, or
via a C-Nav controller solution (i.e. C-Setup, C-Monitor, C-
Scape or C-NaviGator CDU).
Over-the-Air C-Nav Licensing
Over-the-Air (OTA) C-Nav Licensing is the easiest way to
install a C-Nav Corrections Service license. The installation of a
purchased license is accomplished via radio broadcast. Over-
the-Air C-Nav Licensing is especially convenient for receivers
in remote locations in the field.
The customer should do the following in order to properly receive
the CCS Over-the-Air broadcast of the C-Nav license:
1. Turn on the C-Nav5000 Receiver.
2. Ensure that the C-Nav5000 Antenna has clear
access to the CCS tracking satellite.
3. Request the C-Nav license.
Once a C-Nav license is activated, the C-Nav Status LED on
the C-Nav5000 Front Panel will be solid green.
Mailing List
Join the C-Nav mailing list at C-Nav Alert Signup to receive
important announcements from C-Nav Support.
Oceaneering International, Inc.
C-Nav Positioning Solutions
730 East Kaliste Saloom Rd
Lafayette, Louisiana, USA, 70508
E-mail: cnavsuppo[email protected]m
Tel: [phone]
Fax: [phone]
Website: www.oceaneering.com/cnav
C
C- -N Na av v5 50 00 00 0
Q
Qu ui ic ck k S St ta ar rt t G Gu ui id de e