Audio Technica PRO 49Q User manual

PRO 49 Q and PRO 49 QL
REMOTE-POWERED
CARDIOID CONDENSER
QUICK-MOUNT GOOSENECK
MICROPHONES
Frequency in Hertz
Response in dB
10 dB
20k
10k
5k
2k
1k
500
200100
50
LEGEND 12" or more on axis
Frequency Response
Audio-Technica design engineers have utilized
the newest low-mass technology in the quest
for superior performance.The charge is now on
the fixed back plate, rather than the moving
element.With the A-T fixed-charge “back plate”
construction, a gold-vaporized diaphragm just
2 microns thick (about 0.000079") can be
used. This reduces moving mass substantially,
improving frequency response and transient
response while reducing distortion.
The microphone element is enclosed in a
rugged housing with a low-reflectance black
finish.
Operation and Maintenance
Output is low impedance balanced.The output
connector mates with XLRF-type connectors.
The balanced signal appears across Pins 2
and 3, while the ground (shield) connection
is Pin 1. Output is phased so that positive
acoustic pressure produces positive voltage
at Pin 2 in accordance with industry conven-
tion.
DC phantom power (9-52 volts) must be
applied equally to Pins 2 and 3, with the ground
for the power supply connected to Pin 1. This
can be provided by a console or mixer with
built-in phantom voltage or with the addition
of an in-line phantom power supply, such as
the recommended Audio-Technica CP8506
and AT8801 power supplies.
For balanced low-impedance inputs (required
for phantom power), AT8314 cable (or equal)
should be used. Regardless of cables used, it
is important that both ends of each cable are
wired consistently, with the shield always con-
nected to Pin 1 at both ends, Pin 2 connected
to Pin 2, and Pin 3 to Pin 3. This will ensure
that all microphones are electrically in phase
and reduce problems of uneven response
and sound cancellation when two microphones
are used close to each other.
The high sensitivity of the PRO49Q ensures
useful output and an excellent match to most
mixer, tape recorder and amplifier inputs.
It will provide undistorted output even in
sound fields as loud as 134 dB SPL. However,
due to the high sensitivity, in some instances
it may be possible to overload sensitive input
stages. If distortion occurs,
first check for
input overload. In such cases, an attenuator
such as the Audio-Technica AT8202 may be
required between the mic and the electronics
input. (Also, many mixers provide “input pad”
switches to reduce mic-input signal levels.)
The provided AT8146 windscreen simply slips
over the head of the microphone, effectively
reducing wind noise or “popping” when used
extra close.
The small-diameter gooseneck is very easy
to manipulate for proper positioning. It is
heavily lubricated to offer very smooth and
quiet operation. Should it become noisy with
prolonged use, apply a light machine oil
directly on the gooseneck area affected.
While a modern condenser microphone is
not unduly sensitive to the environment, tem-
perature extremes can be harmful. Exposure
to high temperatures can result in gradual
and permanent reduction of the output level.
Avoid leaving the microphone in the open sun
or in areas where temperatures exceed 110° F
(43° C) for long periods of time. Extremely
high humidity should also be avoided.
Description
The PRO49Q is a wide-range condenser
microphone with a cardioid (unidirectional)
polar pattern. It was designed for high-quality
sound reinforcement and other demanding
sound pickup situations. With an overall length
of 13.07", its small-diameter alternating goose-
neck design permits highly flexible positioning
while maintaining a smooth, well-contoured
appearance.The PRO49QL is a 16.46" version
of this microphone.
The PRO49Q features an XLRM-type con-
nector insert at its base, allowing it to be
plugged directly into an XLRF-type jack or
cable connector. The unit’s integral electronics
can be powered from any external 9V to 52V
DC phantom power source.

One-Year Limited Warranty
Audio-Technica microphones and accessories purchased in
the U.S.A. are warranted for one year from date of purchase
by Audio-Technica U.S., Inc. (A.T.U.S.) to be free of defects in
materials and workmanship. In event of such defect, product
will be repaired promptly without charge or, at our option,
replaced with a new product of equal or superior value if
delivered to A.T.U.S. or an Authorized Service Center,
prepaid, together with the sales slip or other proof of purchase
date.
Prior approval from A.T.U.S. is required for return.
This warranty excludes defects due to normal wear, abuse,
shipping damage, or failure to use product in accordance with
instructions. This warranty is void in the event of unauthorized
repair or modification.
For return approval and shipping information, contact
the Service Department, Audio-Technica U.S., Inc.,
1221 Commerce Drive, Stow, Ohio 44224.
Except to the extent precluded by applicable state law,
A.T.U.S. will have no liability for any consequential,
incidental, or special damages; any warranty of mer-
chantability or fitness for particular purpose expires
when this warranty expires.
This warranty gives you specific legal rights, and you may
have other rights which vary from state to state.
Outside the U.S.A., please contact your local dealer for
warranty details.
PRO 49 Q and PRO 49 QL
200 Hz
1 kHz
5 kHz
8 kHz
LEGEND
SCALE IS 5 DECIBELS PER DIVISION
90
60
120
30
150
210
240
270
300
330
180
0
PRO49Q andPRO 49QL SPECIFICATIONS†
Element ..................................................... Fixed-charge back plate
permanently polarized condenser
Polar Pattern ............................................. Cardioid (Unidirectional)
Frequency Response .............................. 70-16,000 Hz
Open Circuit Sensitivity .......................... –37 dB (14.1 mV) re 1V at 1 Pa*
Impedance ................................................ 100 ohms
Maximum Input Sound Level .................. 134 dB SPL, 1 kHz at 1% T.H.D.
Signal-to-noise Ratio1.............................. 66 dB, 1 kHz at 1 Pa*
Dynamic Range (Typical) ......................... 106 dB, 1 kHz at Max SPL
Phantom Power Requirements ............... 9-52V DC, 2 mA typical
Weight
PRO49Q ................................................ 2.8 oz (80 grams)
PRO49QL ............................................. 3.0 oz (84 grams)
Dimensions
PRO49Q ................................................ 13.07" (332.0 mm) long
PRO49QL ............................................. 16.46" (418.0 mm) long
Both ....................................................... 0.47" (12.0 mm) head diameter
0.74" (18.9 mm) base diameter
Output Connector..................................... Integral 3-pin XLRM-type
Accessory Furnished .............................. AT8146 foam windscreen
† In the interest of standards development, A.T.U.S. offers full details
on its test methods to other industry professionals on request.
* 1 Pascal = 10 dynes/cm2= 10 microbars = 94 dB SPL
1Typical, A-weighted, using Audio Precision System One
Optional Accessories:
AT8104a large metal windscreen.
AT8117 large foam windscreen for
high-wind conditions.
CP8201 line matching transformer
(Lo-Z to 50,000 ohms).
AT8202 adjustable in-line attenuator for use
with balanced Lo-Z microphones.
AT8314 2-conductor, shielded, vinyl-jacketed,
broadcast-type cable with XLRF-type connector
at microphone end, XLRM-type connector at
equipment end. Available in 10', 20', 25', 30', 50'
& 100' lengths.
AT8416 shock mount.
CP8506 four-channel 48V phantom power
supply (AC powered).
AT8615 quick-mount plug-in microphone
desk stand.
AT8801 single-channel 48V phantom power
supply (AC powered).
Polar Pattern
PRO49Q
Dimensions PRO49QL Dimensions
56.9 mm
2.24"
12.0 mm
0.47"
44.8 mm
1.76"
18.9 mm
0.74"
13.07"
332.0 mm
418.0 mm
16.46"
44.8 mm
1.76"
0.74"
18.9 mm
56.9 mm
2.24"
0.47"
12.0 mm
Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224
Audio-Technica Limited, Old Lane, Leeds LS11 8AG England
Form No. 0320-0807-01-B/W © 1998 Audio-Technica U.S., Inc. Printed in U.S.A.