Kenwood MC-60A User manual

purchasingthisThankyou
INSTRUCTIONMANUAL
DESKTOPMICROPHONE
for MC-6OAdesktop microphone.
This rrricrophone
performancewhen used
amateurcommunicationssystem. Itprovidesexcellent
has been designed expressly for usewith
your with any
KENWOOD
completewith and isThezinc die-cast base offers
thereby upgradingyour transceiver, existingsystem.
improvedstability
a feather-touch
PTT
anda built-inselector switch, switch, an impedance preamplifier.
serious damage.microphoneas parts. Do notThe microphone is constructedof precision open the it may result in
The andvibration.microphoneissensitive to shock Treat
itwith care.
50W500 IMP.Switch rON/OFF Switch
WIIC AMP INIOUT
(Underside)
UP/DOWN
LOCK Switch
Switch
Connectto
Radio Mic
Terminal
- PTT Switch
KENWOOD
KENWOOD CORPORAl'ION
0 B62-1643-00 (M)
090807060504030201 00
Installing the Batteries
1 Removethe 4 screwsfrom the baseof the
rrricrophoneand gently basefrom theseparate the
rr~icrophone
installthenot need toconnector,you through its microphonetransceiversupplies
Replacethe
marked inpolaritieswith
batteries into the battery compartment,Inserttwo unit. 2 AA
beingsureto matchthe those
the compartment.
3 4 screws.
Note: If your power
do two
AA batteries.
111 Batteries
"AA"hlkaline
(Not Ni-Cd)
Il
the non-coiledcable
ontheSlidethe microphone
Connecting to the Transceiver
1 intothe bracket base
stand.
2 Connect ,from
retractablecable
the microphone.to the ofthe basethe rear stand rear of
3 Connectthe from the baseto the
transceiver'smicrophonejack.

Firstreniove microphone,then slidethe baseof the .the
switch to tlie turn the IN positionto preamplifier ON.
Transmitting
transmit, pressand holdthe
bypassedand
With the switch inthe OUT position,the preamplifier is
the batteriesare disconnected. To conserve
To PlT
intothe microphone.
turn the preamplifier
switch,then speak
batterypower, OFF when it is not in
use.
The MC-6OA switchwhich allowsequippedwith ais LOCK
lockthe Withthe switch in the
IN position,the preamplifier is ON and
youto PlT
pressingit. While pressing operated equipment.
be usedwith
switchdownwithout continuously the microphonecan
VOX
the PlTswitch, pressthe
LOCK
switchtokeepthePlTswitclilocked.ToreleasetheL0CK . Oneral:ionWi3thouttheBaseStand
switch,sim~lvDress it aaain.
I
. .r. -
the basemicrophonewithoutcan usetheYou stand by
When you have finished release
the PIT switch
connectingthe microphonetothe retractablecable,then
the microphoneimpedance
Impedance Selection
you canthe transceiver. Doingso means
to receive. directlyto no
You can set to 500 i2 or
50 ki2. Slidethe 50W500 switch on IMP. thetop of the
microphone
this microphonewith anycan use
your desired position.to
Microphone Preamplifier
You KENWOOD
SSB mobiletransceivers.
transceiver. It has been designed especiallyfor FMand
You cancontrolthe preamplifier
usingthe
MICAMP INIOUT
longer use
the transceiver. switch on the insideof the baseof
the preamplifier,which is built info
transceiver,youto theWith a direct connection
the base
stand. mustuse
the
ONIOFF
to the OFFtransmit, and positiontoto the ONwhen you transmit. Slidethe switch the microphoneswitch located on the top of positionto receive.
UPIDOWN Switcli
Usethe UPIDOWN
further details on how to select
your transceiver instruction
switchto select the transceiver's
operatingfrequency. Referto
manualfor an operating
frequency.
Type:
Cornmunical:ion dynamic microphonetype with PlT
Frequency response:
circuit.
Element:
Impedance:
Sensitivity:
Microphone
Preamp out
Preamp in
Microphoneor preamp off
Preamp on
Recorr~mended
type, unidirectional
from microphone:
operatingdistance
Movingcoil
Dualimpedance
(1000 Hz)
50 ki2 f30%, 500 i2 f
switch selectable
30%
slide
(0 dB = 1 V/ pBAR, 1000 Hz)
150 HZ - 10 kHz
inches) minimum
(-6 dB)
200 Hz - 7 kHz (-6 dB)
10 cm (4
MIC unit connection
Impedance
50k-500
p (White) 1
(Green)
P. T.T
MIC stand connection MIC AMP
IN-OUT
cableconnectionMIC
PG-4C
(Black)
(Shield)
A (Yellow)