Audio Technica 60th ANNIVERSARY AT-LP2022 User manual

AT-LP2022
Belt-Drive Turntable
User Manual
English

1
Introduction
This product can be used only in the countries where the product is sold. Make sure that the operating voltage and the
plug of AC adapter of the product are correct for the country you live in.

2
Safety precautions
Although this product was designed to be used safely, failing to use it correctly may result in an accident. To ensure
safety, observe all warnings and cautions while using the product.
Important information
Warning
To prevent fire or shock hazard, do not expose this apparatus to rain or moisture.
Caution
Do not expose this apparatus to drips or splashes.
To avoid electric shock, do not open the cabinet.
Refer servicing to qualified personnel only.
Do not expose this apparatus to excessive heat such as sunshine, fire or the like.
Do not subject this apparatus to strong impact.
This apparatus should be located close enough to the AC outlet so that you can easily grasp the AC adapter at any
time.
In case of emergency, disconnect the AC adapter quickly.
Do not place any objects filled with liquids, such as vases, on this apparatus.
To prevent fire, do not place any naked flame sources (such as lighted candles) on this apparatus.
Do not install this apparatus in a confined space such as a bookcase or similar unit.
Install this apparatus only in the place where ventilation is good.
The rating label is put on the bottom of this apparatus.
For customers in the USA
FCC Notice
Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Caution
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to
operate this equipment.

Safety precautions
3
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Contact
Responsible Company: Audio-Technica U.S., Inc.
Address: 1221 Commerce Drive, Stow, Ohio 44224, USA
Tel: [phone]
For customers in Canada
ISED statement
CAN ICES-003(B)/NMB-003(B)

4
Notes on use
Turntable body
Do not set and use the product in locations that are considerably hot or humid, dirty, or subject to extreme vibrations.
The product should be positioned on a flat, level surface.
When closing the dust cover, close it completely.
Cartridge
Attach the provided protector to the cartridge when the product is not in use.
Do not touch the stylus of the cartridge with your finger.
Do not allow the cartridge's stylus to bump against the platter or the edge of the record.

5
Package contents
Make sure that you have all the included items before using this product.
If some items are missing or damaged, contact your local Audio-Technica dealer.
After purchase, we suggest that you save all packaging materials for possible future storage, moving, or shipping.
1
89 10 7
6
3
45
2
11
14 15 12 13
1
Turntable body
2
Platter (with drive belt)
Remove the protective sheet before use.
The side where you can see the hexagonal nut (see figure) is the back side of the platter. Be mindful of the front and
back when installing.
3
Drive belt
4
Dust cover

Package contents
6
5
Dust cover hinges
6
Headshell (AT-HS4 SV) with VM stereo cartridge (AT-VM95E BK)
7
Replacement stylus (AT-VMN95SH CL)
8
Counterweight
9
45 RPM adapter
10
AC adapter (Approx. 1.5 m (4.9'))
11
RCA audio cable (Approx. 1.0 m (3.3'))
12
Hexagonal wrench (For tonearm height adjustment)
13
Gloves
14
Quick Start Guide
15
Caution Guide

7
Part names and functions
Top view
1
5
2
3
6
4
1
Motor pulley
2
Drive belt
3
Platter
4
Spindle
5
Control knob
Use to select the platter speed (33-1/3 or 45 RPM) or start/stop the platter.
6
Tonearm

Part names and functions
8
Rear view
1 12 23 4 5 6
1
Dust cover hinge holders
Attachment points for dust cover hinges.
2
Feet
Adjust the level of the product.
3
Ground (earth) terminal
Connect the amplifier's ground (earth) terminal to this terminal using the RCA audio cable's ground line.
4
Stereo output terminals
Connect the RCA audio cable. Connect it to the amplifier's PHONO input jack. The red terminal is the right channel
and the white terminal is the left channel.
5
Power input jack
Connect the AC adapter.
6
Power switch
Turn on/off the power.

Part names and functions
9
Tonearm
1
7
6
8
2
3
5
4
9
10
1
Counterweight
Balances the tonearm and adjusts to provide the proper tracking force.
2
Tracking force gauge ring
Use to adjust the tracking force.
3
Tonearm lift
Moves the tonearm vertically to and from the face of the record.
4
Tonearm rest with clamp
Use the clamp to secure the tonearm so that it does not move.
5
Anti-skate control dial
While the record is playing, a force acts on the stylus tip to pull it inward. This force can be counteracted by setting
the same values for anti-skate and the tracking force.
6
Tonearm height adjustment socket
7
Tonearm lift control lever
Operates the tonearm lift.
8
Tonearm