audiophony BM-Check User manual

USER GUIDE
H11389 - Version 2 / 03-2023
BM-Check
Made in France
≥ +3 dB
≤ -3 dB
0 dB
Prosthesis simulator for loop amplifier with headphones

BM-Check - Prosthetic simulator for loop amplifier testingEnglish
Page 2
Made in France
≥ +3 dB
≤ -3 dB
0 dB
1 - Product presentation
2 - Componants
The magnetic loop earpiece is a compact device that allows people without hearing aids to listen
to a hearing loop system as if they were wearing a hearing aid in the"T" position.
It can be used for:
- Check the sound source of a magnetic loop
- Equipping a person who is hard of hearing and who does not have a hearing aid
- Equiping a person with hearing loss whose prosthesis does not have a"T" position.
Note: The BM-Check is a magnetic eld meter and approved by the EN60118-4 standard.
Signal level and power LEDs :
Red LED : Non-compliant installation
(reception too high > -3dB).
Green LED : Loop conforms to the
standard (between -3dB and 0dB).
Orange LED: Product on and
installation not in conformity (reception
too low < -3dB).
Headphone
Headphone jack
Volume control and power button
USB connector for charging the battery: The LED is red
during charging and turns green when the charge is
complete

AUDIOPHONY PUBLIC ADDRESS English
Page 3
3 - Operation
The hearing loop tester works with an internal battery.
1.Place the headset on your ears and adjust it for comfortable listening.
2.Hold the hearing loop tester vertically and at head height to mimic the position of a hearing
aid.
3.Turn the unit on by turning the volume control slightly clockwise until a comfortable listening
sound is obtained. Turn the knob in the opposite direction to decrease the volume if
necessary..
4. If the orange LED does not light, check that the internal battery is correctly charged.
5.When you are nished using the headset, turn the volume knob counterclockwise until the
LED turns o󰀨.
Important
Always turn o󰀨 the unit when it is not in use to extend its life.
Always hold the hearing loop tester at ear height and upright when listening to a loop system to
ensure the best possible performance.

BM-Check - Prosthetic simulator for loop amplifier testingEnglish
Page 4
4 - Maintenance
5 - Troubleshooting
To extend the life of the product, perform the following operations regularly:
Clean the unit with a soft, dry cloth or suitable cleaning wipes. Do not use solvent-based cleaners
and avoid getting all kinds of liquids into the hearing loop listener.
Turn o󰀨 the headset when not in use.
Keep the battery charged.
Symptom Possible fault Action
Ignition orange LED
does not light up.
1. The battery is empty
2. There is an internal fault
1. Connect the tester to a USB charger
2. Contact your dealer
No loop sound is heard
in the hearing loop
listener.
1. Sound is not loud enough.
2. The tester is not at an
appropriate distance to listen
to the loop.
3. The magnetic loop does not
work.
4. The headphone has a
problem.
5. Internal fault.
1. Turn up the volume.
2. Bring the hearing loop listener
closer to the loop.
3. Use another hearing loop tester
or listening system (if possible) to
make sure the loop works. If no
sound is coming out of the loop,
contact your dealer.
4. Replace the headphone.
5. Follow step 3. If the sound is heard
with another device, contact your
dealer to change the hearing loop
tester.

Because AUDIOPHONY®takes the utmost care in its products to make sure you only get the best possible quality, our products are
subjects to modifications without prior notice. That is why technical specifications and the products physical configuration might differ
from the illustrations.
Make sure you get the latest news and updates about the AUDIOPHONY®products on www.audiophony-pa.com
AUDIOPHONY®is a trademark of HITMUSIC S.A.S - Parc d'activités Cahors sud - 46230 FONTANES - FRANCE