Audiovox Prestige Platinum 128-8549 User manual

128-8549
1 of 24
Page1
Model APS-997N
Owner’sManual
IMPORTANT ! In order to provide you with the highest level of security to your
vehicle, this system is equipped with selectable manual override circuitry. It is
possible that you will need to override you security system if the transmitter
becomes lost, or inoperative due to battery failure. Reading the sections on
"Manually Overriding Your System" is necessary to fully understand the procedure
required to enable your vehicle in such situations. In addition, the chart on the last
page of this manual has a section for the particular features and options installed
in your vehicle as well as the override method selected. Although the default
mode is "Valet Switch" operation, the system can be configured for "Custom
Code" operation for enhanced security. Confirm the override mode selected on
the last page of this manual, and familiarize yourself with the section on it's opera-
tion.
FEATURES :
1 Two Way 5 Button Remote Control And 1 One Way 5 Button Remote Control
Six Channel Code Learning Programmable Receiver
External Superheterodyne Transceiver Antenna
Single Or Two User Programmable W/Separate Control Outputs
Single Button Lock/Unlock or Separate Button Lock/Unlock or Both
Remote Keyless Entry With Optional Access Guard (must have power door
locks)
Selectable Manual Override Mode
New Enhanced Panic Feature (Any button other than unlock stops siren, no
change to the units state)
Smart Disarm (If triggered, elect to shut off siren, or disarm entire unit )
Adjustable Shock Sensor Via The Transmitter (Pre-Detect Off, Pre & Full Detect
Off,CityMode)
Safe Start Output Controlled From Channel 3 (Option Channel 3 ForTrunk, Or
For R/S)
24 Hour Time Start Mode
Cold Temperature Start Mode
2 or 4 Hour Automatic Start Mode
Parking Meter Count Down Timer On LCD Remote
Additional Count Down Timer Mode
Remote Panic InAll Modes (Press & Hold Lock /Unlock Button For 3 Seconds
To Engage)
Improved Custom Code Override, User Selectable and Programmable
5 Button Remote Start Security System With
Plug-In Shock Sensor & Starter Disable

128-8549
2 of 24
Page2
Protected Push Button Valet/Override Switch
7-Function LED-Arm / Disarm / Zone 1 / Zone 2 / Zone 3 / Valet / Arming
Intrusion Alert With Memory
Instant Siren Activation
Starter Disable Output
Additional Engine Immobilizer Output, (Optional Relay Required)
True Last Door Arming (Hardwire Only)
Defective Zone By-Pass
Defective Zone Chirp Confirmation (Unit Chirps To Report Zone Cleared)
6 Tone Mini Siren
Car Horn Output ForAdditionalAlarm Response (Improved Timing To Minimize
RF Interference.)
Additional Negative Trigger Input (Hood and Trunk)
RF Inhibit With Ignition On
Parking Light Flasher (Relay On Board)
Plug In Dual Stage Shock Sensor (Pre-detect, Full Trigger and “City Mode”)
Audible Arm, Disarm, Defect, and Tamper Chirp Indications
Headlight Control Output
Illuminated Entry Control Output
Active or Passive Arming Selectable
Programmable Auto Lock On / Off
Programmable Auto Unlock On / Off/Drivers Door/All Doors
Programmable Door Lock Pulse Duration 1 Second / 3.5 Seconds/1 Sec
L/ Dbl. U/L
Programmable Active or Passive Door Locks
User Programmable Permanent Chirp Delete
On Command RF Chirp Delete from Transmitter Or Selectable Through
Software
Dome Delay Learn Circuitry (Patent Pending)
OPTIONS :
Remote Trunk Release (must have electric trunk release)
Remote Keyless Entry (must have power door locks)
Multiple Vehicle Capable
Remote Power Window Roll Up
Remote Garage Door Interface
CAUTION! Be certain that the vehicle is outdoors before using this or any remote
vehicle starting device. A running engine produces dangerous car-
bon monoxide fumes which can be harmful or fatal if prolonged expo-
sure occurs. DO NOT remote start the vehicle if it is garaged.
YOUR“CODEHOPPING“TRANSMITTERS
The transmitters included with your new security system use the most advanced
and secure form of radio frequency transmission available on any current auto-
motive security system. Some of today’s sophisticated auto thieves use a device

128-8549
3 of 24
Page3
known as a code grabber, which will receive and store the signal from your
keychain transmitter and re-transmit at a later time to disarm your system.
Your Keeloq Code Hopping transmitters will change their signal every time the
button is pressed, so when a thief grabs then re-transmits your signal, the alarm
system will not respond.
If your transmitter button is pressed more than fifty times while it is out of range of
the vehicle (children playing with your keys), the transmitter will not operate when
you return to the vehicle, and will need to be re-aligned to the receiver. To do this,
simply press button 1, (lock), two times within a one second
time period. The system will now respond to that transmitter
each time a button is pressed.
NOTE: This system is custom configurable and can be set
up to operate with a number of options controlled from any
transmitter button or button combination. For reference, we
will describe operation assuming that your system is pro-
grammed for separate lock and unlock buttons. Also reference
will be made to the icons as shown on the buttons left.
NOTE: The LCD based remote will be explained in detail fur-
ther in this manual See "System Status" described later in this
manual. Consult your installation center if your system has
been configured differently.
NOTE: Your system has the option of using a siren, the vehicle horn, or both for
the sounding device. Where the siren is referenced below, the horn or
both may in fact chirp, or beep.
ARMINGTHE SYSTEM-ACTIVE
1. Turn off the engine, exit the vehicle, and close all doors, hood lid and trunk lid.
2. Press and release Lock/Arm button on the keychain transmitter.
The dash mounted LED begins to flash slowly.
Parking Lights flash one time.
Siren sounds one chirp.
If the siren/horn sounds 3 chirps, then you have left a door, trunk, or
hood lid ajar. Simply close the opened entry point to provide full protec-
tion. If the siren "chirped" three times, sometime after arming, the
exclusive delayed dome light learn circuit has been programmed and
the system detected a open entry point after the learned delay expired.
Again, closing the hood, trunk, or doors will correct the problem and you
do not need to disarm the system to make the correction. If the siren/
horn did not sound when arming, then the chirps have been turned off
and you should refer to the section titled "ELIMINATING THE ARM/DIS-
ARM CHIRPS" in this manual.
Doors Lock - Optional
NOTE: If the optional Headlamp illumination feature has been added, and has
been selected for operation when arming, as an added convenience, the
system will turn on the headlights when the system is armed.
SILENT ARMING - ACTIVE (Must be activated during programming)
1. Turn off the engine, exit the vehicle and close all doors, hood lid and trunk lid.
2. Press and hold the Lock/Arm button on the keychain transmitter for 2
seconds.

128-8549
4 of 24
Page4
The dash mounted LED begins to flash slowly.
Parking Lights flash one time.
Siren will not sound.
If the siren "chirped" three times, sometime after arming, the exclusive delayed
dome light learn circuit has been programmed and the system detected a open
entry point after the learned delay expired. Closing the hood, trunk, or doors will
correct the problem and you do not need to disarm the system to make the
correction.
Doors Lock - Optional
NOTE: If the optional Headlamp illumination feature has been added, and has
been selected for operation when arming, as an added convenience, the sys-
tem will turn on the headlights when the system is armed.
The LCD Remote has the following response:
ARMINGTHE SYSTEM-PASSIVE (AUTOMATIC)
(Must be activated during programming)
1. Turn off the engine, exit the vehicle and close and lock all doors, hood lid and
trunk lid.
The dash mounted LED begins to flash rapidly, indicating 30 second passive
arming has begun.
2. Opening any protected entry point during the 30 second passive arming cycle
will immediately suspend automatic arming and the 30 second passive arm-
ing cycle will restart when all doors are closed. At the end of the passive
arming cycle;
The dash mounted LED begins to flash slowly.
Parking Lights flash one time.
Siren sounds one chirp
If the siren did not sound when arming, then the chirps have been turned off and
youshouldrefer to the section titled “ELIMINATINGTHEARM/ DISARM CHIRPS“
in this manual.
Doors Lock - Optional
Door locking during passive arming is a selectable feature. The alarm can be
programmed to allow the doors to lock only when arming using the keychain
transmitter and they will not automatically lock during passive arming.
PROTECTIONWHILE THESYSTEMISARMED
Opening any protected door, hood or trunk lid will cause the alarm to imme-
diately sound. The alarm will continue to sound for 30 seconds, then stop and
continue to monitor all protected entry points. If the thief left a door opened, the
alarm will sound for six 30 second cycles, remain armed and ignore that trig-
gered zone.\
Whenever the system is armed, the dash mounted LED indicator will slowly
flash. This serves as a visual deterrent to the potential thief. The LED is a very
low current bulb and will not cause the vehicle’s battery to drain, even when left
unattended for extended periods.
Whenever the system is triggered, the vehicle’s parking lights will flash for the
full 30 second alarm cycle, attracting visual attention to the vehicle.
Optional - Whenever the system is armed, the vehicle’s starting circuit will be
bypassed. If the thief should choose to ignore the siren, the vehicle can not be
started.

128-8549
5 of 24
Page5
Any mild impact to the vehicle’s glass will cause the alarm to sound a short
series of warning tones.
Any strong impact to the vehicle’s glass will cause the alarm to trigger for the full
30 second alarm cycle.
NOTE: If the optional interior illumination circuit was installed, the interior light
will flash as well for the full 30 second alarm cycle.
DISARMINGTHESYSTEM
NOTE: If the optional 2 step door unlock circuit is installed, when the unlock
transmitter button is activated, the drivers door only will unlock, pressing the
unlock button a second time will cause all doors to unlock.
NOTE: If your transmitter has been configured with single button Lock/Unlock, to
activate the all door unlock feature operate the Lock/Unlock button a second
time within 3 seconds of the first unlock command.
1. As you approach the vehicle, press and release the Unlock/Disarm button on
the keychain transmitter.
The dash mounted LED turns off.
The LED will start flashing rapidly, indicating that the system is re-arming
automatically. Open any door to suspend the automatic arming.
Parking Lights flash two times.
If the parking lights flashed three times, then the alarm was triggered in your
absence. Before turning the key on, examine the LED to identify which zone was
triggered.
Siren sounds two chirps.
If the siren sounds 4 chirps, then the alarm was triggered in your absence. Before
turning the key on, examine the LED and refer to the INTRUSION WARNING
SIGNALS section of this manual to identify which zone was triggered.
If the siren did not sound when disarming, then the chirps have been turned off
and you should refer to the section titled “ELIMINATING THEARM / DISARM
CHIRPS“ in this manual.
Doors Unlock - Optional
2 Step Doors Unlock - Optional
NOTE: If the optional Headlamp illumination feature has been added and has
been selected for operation when disarming, as an added convenience, the
system will turn on the headlights when the system is disarmed.
SILENT DISARMING (Must be activated during programming)
Note: If the optional 2 step door unlock circuit is installed, when the unlock
transmitter button is activated, the drivers door only will unlock, pressing the
unlock button a second time will cause all doors to unlock.
NOTE: If your transmitter has been configured with single button Lock/Unlock as
shown, to activate the all door unlock feature operate the Lock/Unlock button a
second time within 3 seconds of the first unlock command.
1. Press and hold button the Unlock/Disarm button on the keychain transmitter for
2 seconds.
The dash mounted LED turns off.
The LED will start flashing rapidly, indicating that the system is re-arming
automatically. Open any door to suspend the automatic arming.

128-8549
6 of 24
Page6
Parking Lights flash two times.
If the parking lights flashed three times, then the alarm was triggered in your
absence. Before turning the key on, examine the LED to identify which zone was
triggered.
Siren will not sound.
If the siren sounds 4 chirps, then the alarm was triggered in your absence.
Before turning the key on, examine the LED and refer to the INTRUSION
WARNING SIGNALS section of this manual to identify which zone was triggered.
Doors Unlock - Optional
2 Step Doors Unlock - Optional
NOTE: If the optional Headlamp illumination feature has been added and has
been selected for operation when disarming, as an added convenience, the
system will turn on the headlights when the system is disarmed.
WHILETHE SYSTEMIS SOUNDING
If during a triggered state, you wish to shut off the siren without disarming your
security system, simply press and release any transmitter button other than the
Unlock/Disarm button. This action will turn off the siren yet leave the vehicle fully
armed and protected. This feature is particularly useful if you are aware of children
playing near your vehicle that may accidently trigger your security system. In this
case you can cancel the siren sounding without disarming your alarm.
INTRUSIONWARNINGSIGNALS
This system will inform you if an intrusion attempt has occurred while you were
away from the vehicle. If an intrusion attempt has occurred, the siren will
chirp 4 times and the parking lights will flash 3 times when disarming the
system. Enter the vehicle and observe the red dash mounted LED to identify
which zone was triggered.
If the LED is flashing one time...pause...one time...pause...etc., then an
intrusion attempt was made to the shock sensor, or an accessory trigger-
ing device that may have been added to the system.
If the LED is flashing two times...pause...two times...pause...etc., then
an intrusion attempt was made to a hood or trunk pin switch that was
added to the system or to a light activated entry point if the alarm was
installed using the voltage sensing feature.
If the LED is flashing three times...pause...three times...pause...etc.,
then an intrusion attempt was made through one of the vehicle’s doors.
These intrusion warning indicators are stored in the system’s memory and will
only be erased when the ignition key is turned on.
PUSHBUTTONLED/VALET/OVERRIDE/PROGRAMMINGSWITCH:(PBLED)
The PBLED switch allows you to temporarily bypass all alarm functions, eliminating the
needtohandyourtransmittertoparking attendantsorgaragemechanics.Whenthesystem
isinvalet mode, allalarmfunctionsare bypassed, howevertheremote panic featureand
remotedoorlocks willremainoperational. Tousethe valet mode,thesystem mustfirstbe
disarmed either by using your keychain transmitter, or by activating your personalized
manualoverride code.
1. Enter thevehicle,and turntheignition keytothe onposition.
2. PressandholdthePBLEDswitchuntiltheLEDturnsonsolid. Thesystemwillremainin
thevalet mode.
3. Toreturntonormaloperation,press andrelease thePBLEDswitchanytimetheignition
ison.

128-8549
7 of 24
Page7
NOTE: Alwaysrememberto returnthevehicle tothevaletoff position.Thiswill ensurethat
thevehicleremainsprotectedat alltimes.
MANUALLYOVERRIDINGYOURSYSTEM:
USINGTHEPBLEDOVERRIDESWITCH
Your Security Systemcanbedisarmed without theuseofthe keychain transmitter.Thisis
necessary, sinceyouwillneed the abilitytooperate your vehicleifthetransmitter is lostor
its battery fails. If your system has been selected for Valet Switch manual override as
indicatedonthe lastpageofthis manual,tobypass the alarmsystem;
1. Open the vehicledoor. Thealarm will sound.
2. Turntheignition keytothe onposition.
3. Within5seconds, press andreleasethePBLED override switch.
The alarm system will stop sounding and enter the (bypassed) mode. You can now start
andoperate thevehiclenormally.
Typicallythisoverride modeisused onlyifthetransmitter hasbecomeinoperative.
Programming Your Custom Override Code:
Unlikeoverrideswitcheseasilyfound, and defeated, this security systemallowsthecon-
sumer to program a personal override code, offering a higher level of security. To take
advantageof thisoption,programmablefeature#10must beselected forthe CustomCode
Option. Consultyourinstallation centerforprogrammingdetails. Thesystem comesfrom
the factory with a pre-programmed override code of 11. To change this default override
code,dothefollowing:
1. Disarm the system by use of the transmitter, or by use of the emergency override
sequence.Turn theignitionswitchto theonposition.
2. Within 10seconds,press and releasethePBLED switch,3times.
3. Within 10 seconds turn the ignition switch off, on, off, on, off, on.
(Thesirenorhorn will beep andthelightswill flash one time.)
4. Within 10seconds,begintoenter yourchosen10thsdigitby pressingandreleasing the
PBLEDswitchfrom 1upto 9times.
5. Within 10secondsofthelast entered 10ths digit,turntheignitionswitch off then on.
6. Within 10seconds,begin toenteryour chosenunitsdigit by pressingandreleasing the
PBLEDswitchfrom 1upto 9times.
7. Finish byturningtheignition switch to theoffposition.
Ifthenew code wasaccepted,the unit willreportback the newlyenteredcode, by flashing
theLED, firstindicatingthe10thsdigit, pauseandthentheunits digit.The unitwillreportthe
new code three times with a one second pause between each code, then the system will
beginarming. IftheLED flashpatternreportsthepreviously storedcode,thenewcode was
notenteredcorrectly. Please repeatsteps 1 through7aboveconsidering the following.
NOTE: Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0
(Zero),ornodigit entered in anyplace,unitsor tenths.
NOTE: If15secondsofinactivityexpire, or if the ignition switch is turnedoffformorethen
5 seconds during any of the above steps, the unit will revert back to the last
successfully stored code.
Custom Code Programming Example:
To Change the code from the factory pre-assigned code of 11 to “52” you would do the
following:
1. Disarm the system by use of the transmitter, or by use of the emergency override
sequence.
2. Turn theignitionswitch to theonposition.

128-8549
8 of 24
Page8
3. Within 10seconds,press and releasethePBLED switch,3times.
4. Within 10 seconds turn the ignition switch off, on, off, on, off, on.
(Thesirenorhorn will beep andthelightswill flash one time.)
5. Within 10seconds,begin topress andreleasethe PBLEDswitchto setthe tenthsdigit.
(Aspertheexample, press and release5timesto set the tenthsdigitto5)
6. Within10seconds ofthe lastpress ofthe pushbutton,turn theignition switchoff thenon.
7. Within10seconds, beginto pressandreleasethePBLEDswitchtosettheunitsdigit.
(Aspertheexample, press and release2timesto set the unitsdigitto2).
8. Turntheignition switch totheoff position. Immediatelyobservethe LED flashpattern.
YouwillnotetheLEDflashingfivetimes,pause,andthenflashtwotimes,pause.Thispatternwill
berepeatedthreetimesindicatingthenewcode(52)hasbeenacceptedandstoredinmemory.
NOTE: If after step 7, the LED flashes a code other than what was just entered, this
indicates that the code has not been changed. You will have to repeat steps 1
through7above being certaintonotethe following:
Acceptabledigits 10thsorunits are1through9.The unitwillnot recognizea0(Zero),or no
digitenteredin any place,unitsor tenths.
NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for more then 5
seconds during any of the above steps, the unit will revert back to the last successfully
storedcode.
MANUALLYOVERRIDINGYOURSYSTEM:
USINGTHECUSTOMCODEOVERRIDE
Assumingtheoverride codeprogrammedhas not beenchanged,and thedefaultoverride
codeof11isin the system's memory.
1) Enterthe vehicle andturntheignition switchtotheon position.
NOTE:The sirenwillsound.
2) Within5 seconds, pressandrelease thePBLEDswitch 1 time.
3) Within5 seconds, turn the ignitionswitchoffthenon.
4) Within5 seconds, pressandrelease thePBLEDswitch 1 time.
5) Turnthe ignition switch off then onandstartthevehicle.
NOTE: Ifyouhave changed theprogrammedoverride codethensubstituteyour newcode
tenths for step 2 above, and units for step 5 above.
ELIMINATING THENORMAL ARM/DISARMCHIRPS
You can selectively eliminate the normal arm & disarm chirps by holding the transmitter
buttonslightlylongerwhen arming or disarming. This willpreventthesiren chirps for one
arm or disarm cycle. If you find this inconvenient and wish to eliminate these chirps
permanently,
1.Turntheignitionswitch 'on" then 'off".
2.Within 10seconds ofturning offthe ignition,pressandreleasethePBLEDswitch3times.
3.Ifthechirps were on beforeyoustarted,thesiren will emit 2shortchirpsindicating that
thechirpsarenowoff. Ifthe chirps were off before you started,thesirenwillemitone
shortchirpindicatingthatthe chirps are now on.
NOTE: If the vehicle battery is disconnected then reconnected, the unit will return to the
defaultsetting ofchirps on. Repeatthe aboveprocedure toeliminatethearm/disarm
chirps.
NOTE: Your system must be programmed by the installation center to en-
able this feature.
NOTE: Whenever the chirps are bypassed, the 4-chirp intrusion indicator
and 3 chirp defective zone indicator will always operate. Since these are

128-8549
9 of 24
Page9
important warnings to you that something has happened, they cannot be
eliminated.
NOTE: Your system must be programmed by the installation center to en-
able this feature.
REMOTEPANICOPERATION
The Lock or Unlock button on your keychain transmitter also functions as a panic
switch for use in emergency situations. To use remote panic,
1. Press and hold the Lock or Unlock button on the keychain transmitter for 3 or
more seconds. The alarm will immediately sound.
2. To stop the alarm, press and hold the Lock or Unlock button on the transmitter
again for 3 seconds. If the button is not pressed, the alarm will automatically
stop after 30 seconds. Also if any transmitter button other than the Lock or
Unlock button is pressed and released, the Panic mode will be turned off
immediately. The normal function of this transmitter button will be suspended
during the Panic sounding period.
3. During the panic mode, the Lock and Unlock buttons can be used to lock and
unlock the doors, (if the option is installed), however once the unlock/disarm
button is pressed, the vehicle's starter inhibit device, (where installed) will be
disabled allowing the vehicle to start.
NOTE: While in the Panic mode, pressing and releasing the Lock or Un-
lock buttons will, if the option is installed, lock and unlock the doors respectively.
While in the panic mode, anytime the Unlock button is pressed, the panic feature
will continue for the allotted 30 seconds, however, the security system will be
disarmed allowing the vehicle to start.
RFSHOCKSENSORMODESELECTION
The way in which your alarm system reacts to threatening vibrations, created by
attempts to enter the vehicle by breaking a window, is adjustable by the transmitter
immediately after arming. There are 4 modes of operation that can be selected
by the operator:
1. Normal Operation (default mode)
In this mode, any strong vibrations will cause the siren to sound (full
detect) for 30 seconds. Any lesser vibration will cause the siren to emit
about 6 short warn away chirps, (pre-detect).
2. Stage 1 (Omit pre-detect)
In this mode, the warn away chirps created by the lesser vibration will be
deleted. If strong vibration occurs, the siren will sound.
3. Stage 2 (Omit pre & full detect)
In this mode, both the pre-detect stage and the full trigger stage of the sensor
are defeated. The unit will not react to vibration of any magnitude.
NOTE: Shock Sensor Icon Is Displayed On The LCD Panel.
4. Stage 3 (City Mode)
In this mode, the pre-detect chirps will change from six pre-warning tones to
a full 10 seconds of warning chirps.
The full detect trigger duration will be reduced from 30 seconds to 15 seconds.
NOTE: Setting the stage of the shock sensor will be effective for one arming
cycle only. Once the system has been disarmed, the very next arming
cycle will cause the sensor to default to the normal operation stage.
To change or adjust the shock sensor, press and release the ARM button of you
keychain transmitter.

128-8549
10 of 24
Page10
1.Within 2 seconds of arming, press and release the ARM button 1 time, to
defeat the pre-detect stage of the shock sensor. (The lights will flash and the
siren will chirp once.)
2.Within 2 seconds of step 1, press and release the ARM button 2 times, to
defeat the pre and full detect stages of the shock sensor. (The lights will
flash and the siren will chirp twice.)
3.Within 2 seconds of step 1, press and release the ARM button 3 times to
enter the "City Mode" of operation. (The lights will flash and the siren will chirp
three times.)
While under control of the remote start the system can be programmed to allow
you to shunt the shock sensor from the transmitter. If the system has been such
programmed, simply press the lock button of your keychain transmitter anytime
during the remote start cycle. The shock sensor will be shunted for the entire run
cycle and will resume normal operation after the remote start unit shuts off.
Check with your installation center to determine if this feature has been pro-
grammed into your system.
PBLEDSAFETYCONTROLSWITCH
The Push-Button LED control switch allows you to temporarily disable the remote
starting function of the system. This recommended whenever the vehicle is being
serviced. To place the system in the service mode:
1) With the system disarmed/unlocked, and the ignition switch off Press and
Hold the PBLED on.
2) Turn the ignition switch on, off, on, off, on, off.
3) The LED begins to flash two short flashes followed by one long flashes and
continues this pattern until returned to normal mode of operation.
This puts the unit into the R/S Override mode indicating that the remote start is
in the service mode and will not start from RF or any other input Posse or
otherwise.
To Exit R/S Override Mode
1) With the system disarmed, Press and Hold the PBLED on.
2) Turn the ignition switch on, off, on, off, on, off.
3) The LED turns off indicating that the R/S unit is fully functional one again.
REMOTESTARTINGTHEVEHICLE
The system WILL NOT start the vehicle if any one of the following conditions
exists:
1. The Vehicle Hood Is Opened.
2. The Gear Selector Is InAny Gear Other Then Park.
3. The Brake Is Depressed.
4. The Safety Control Switch Is In The Off Position.
WARNING! Be certain that the vehicle is outdoors before using this or any remote
vehicle starting device. A running engine produces dangerous carbon
monoxide fumes which can be harmful or fatal if prolonged exposure
occurs. DO NOT remote start the vehicle if it is garaged.
To Remote Start The Vehicle:
Press and release the programmed channel of your keychain transmitter two
times within 2 seconds. The vehicle will start and remain running for the pre-
programmed 5, 10, 15, or 20 minutes. As a visual indication, the parking lights
will flash or turn on depending on the programming set up by your installation
center.

128-8549
11 of 24
Page11
When you arrive at your vehicle, disarm the alarm system by pressing and re-
leasing the arm/disarm button of your keychain transmitter. Enter the vehicle and
turn the ignition key to the on position.
CAUTION! Do not turn the key to the start position. This will cause the starter
motor to engage with the already running engine which could result in
damage. Step on the brake pedal to disengage the remote start unit.
The vehicle will continue to run but now on it's own power.
NOTE: The engine will stop running before the expiration of the pre-programmed
run timer if you complete any of the following:
1. Press and release the programmed channel of your keychain transmitter two
times within 2 seconds.
2. Depress the brake pedal.
3. Open the hood.
4. Move the red handled control switch to the off position.
5. Race the engine to above 4000 RPM.
OPERATING ONAUTOMATICSTARTUPTIMERMODE
Your system has the ability to automatically start the vehicle every 2 or 4 hours
over a 48 hour period. This feature is especially useful in cold climates where
the only means to keep the engine and engine fluids warm is to periodically start
the engine.
WARNING! Be certain that the vehicle is outdoors before using this or any re-
mote vehicle starting device. A running engine produces dangerous
carbon monoxide fumes which can be harmful or fatal if prolonged
exposure occurs. DO NOT remote start the vehicle if it is garaged.
TOBEGINTHEAUTOMATICSTARTUPTIMER
1. Turn the ignition key on then off.
2. Within 10 seconds, activate the RF start command two times. (Push the
programmed channel button of your keychain transmitter 4 times).
The parking lights will flash and the siren will chirp 4 times indicating the timed
start mode is activated.
The vehicle, on a 2 or 4 hour interval basis, will automatically start, run for
the pre-programmed time (5,10,15 or 20 minutes), and then shut off. This
will continue for 48 hours.
NOTE: The automatic start up timer can also be initiated from the keychain
transmitter. To do this:
1. Start the vehicle using the keychain transmitter by pressing and releasing the
second channel transmitter button 2 times.
2. Shut off the vehicle using the keychain transmitter by pressing and releasing
the second channel transmitter button 2 times.
3. Within 10 seconds of step 2, activate the RF start command two times. (Push
the second channel button of your keychain transmitter 4 times).
The parking lights will flash and the siren will chirp 4 times indicating the timed
start mode is activated.
CANCELINGTHEAUTOMATICSTARTUPTIMER
To cancel the automatic start up timer do one of the following;
1. Start the vehicle manually with the use of the ignition key and depress the
brake pedal.
2. Remote start the vehicle using your keychain RF transmitter.

128-8549
12 of 24
Page12
NOTE: Option button used in combination is only available on the alternate re-
mote transmitter and not available on the LCD Transmitter.
OPTIONALDEVICE OUTPUT(CHANNEL 3)
Controlled By: Trunk/Key Button
Other Transmitter button configurations are also available. Consult your installa-
tion center for other configurations not listed above that may have been pro-
grammed to operate a specific feature of your system.
This security system is equipped with an output which will activate when the
appropriate transmitter button is depressed for 4 seconds. Although this output
is intended to activate the trunk release option, any other optional devices may be
connected to this channel. Consult your installation center for more information
about this output.
ADDITIONALREMOTEFUNCTION(CHANNEL4)
Controlled By: Trunk/Key Button Option Button Lock +
Unlock Buttons Lock + Trunk/Key Buttons Unlock + Trunk/
Key Buttons
Other Transmitter button configurations are also available. Consult your installa-
tion center for other configurations not listed above that may have been pro-
grammed to operate a specific feature of your system.
This security system has an additional feature that can be connected to a num-
ber of different optional accessories. Some of the more common uses for this
channel are;
Remote Car Starter
Remote Window Closure
Remote Garage Door Interface
To remotely operate the device indicated, momentarily press, or press and hold
the appropriate transmitter button(s) as indicated above.
ADDITIONALREMOTEFUNCTION(CHANNEL5)
Controlled By: Trunk/Key Button Option Button Lock + Unlock Buttons 
Lock + Trunk/Key Buttons Unlock + Trunk/Key Buttons
Other Transmitter button configurations are also available. Consult your installa-
tion center for other configurations not listed above that may have been pro-
grammed to operate a specific feature of your system.
This security system has an additional feature that can be connected to a num-
ber of different optional accessories. Some of the more common uses for this
channel are:
Remote Car Starter
Remote Window Closure
Remote Garage Door Interface
To remotely operate the device indicated, momentarily press, or press and hold
the appropriate transmitter button(s) as indicated above.
ADDITIONALREMOTEFUNCTION(CHANNEL6)
Channel 6 is an alternate output that can be controlled by the unlock button of the
transmitter, or by and independent button or combination of buttons. For your
vehicle this output is:

128-8549
13 of 24
Page13
Controlled By: Trunk/Key Button Option Button Lock + Unlock Buttons 
Lock + Trunk/Key Buttons Unlock + Trunk/Key Buttons
Other Transmitter button configurations are also available. Consult your installa-
tioncenterfor other configurations not listedabovethat may have been programmed
to operate a specific feature of your system.
This security system has an additional feature that can be connected to a number
of different optional accessories. Some of the more common uses for this channel
are: Remote Car Starter
Remote Window Closure
Remote Garage Door Interface
To remotely operate the device indicated, momentarily press, or press and hold
the appropriate transmitter button(s) as indicated above.
ADDITIONALREMOTEFUNCTION(CHANNEL7)
Channel 7 is an alternate output that can be controlled by the unlock button of the
transmitter or by and independent button or combination of buttons. For your
vehicle this output is:
Controlled By: Trunk/Key Button Option Button Lock + Unlock Buttons 
Lock + Trunk/Key Buttons Unlock + Trunk/Key Buttons
Other Transmitter button configurations are also available. Consult your installa-
tioncenterfor other configurations not listedabovethat may have been programmed
to operate a specific feature of your system.
This security system has an additional feature that can be connected to a number
of different optional accessories. Some of the more common uses for this channel
are: Remote Car Starter
Remote Window Closure
Remote Garage Door Interface
To remotely operate the device indicated, momentarily press, or press and hold
the appropriate transmitter button(s) as indicated above.
TURBOTIMERMODE
This system provides a means to cool down the vehicles turbo charger, if so
equipped, by allowing the vehicle to continue to run for a prescribed period of time
every time the vehicle's engine is turned off. This feature requires the system to be
set up for turbo timer during installation. Consult with your installation center to be
certain this feature was activated and how long the vehicle will continue to run, 3, 5,
or 10 minutes after the ignition switch is turned off.
To activate the turbo timer:
Anytime the engine is running for more than 15 seconds:
1) Place the gear selector in park.
2) Set the parking, (hand), brake.
3) Be certain your foot is off the brake pedal.
4) Press the program/Push-Button switch 2 times within 5 seconds.
The parking lights will flash two times indicating the mode was successfully en-
tered.
If your parking lights flashed four times, this indicates the turbo mode was on and
is now turned off.

128-8549
14 of 24
Page14
With the turbo timer mode selected on, after you've arrived at your destination,
while the engine is still running, set the parking brake, pause 2 seconds, then turn
the ignition switch to the off position. The engine will continue to run the allotted
time according to the selection during installation.
If you do not want the vehicle to continue to run for one cycle, simply step on the
vehicle's brake, or release the parking brake, or activate the transmitter's start
button two times in succession. Any of these will cause the engine to turn off.
TELEMATICUPGRADE:
This system has the ability to have a telematic upgrade module connected to it.
This is a upgrade that can give you control of certain functions of your vehicle from
a Telephone, or in some cases a computer interface. Please check with your
installation center for most recent Telematic Upgrades. If you had a Telematic
Upgrade installed, the manual supplied with the upgrade unit will provide a op-
erators manual advising of the features of the system and means available to
control these features of your vehicle.
TRANSCEIVERICONSANDTHEIRINDICATIONS
When Disarmed, Press the Arm/Lock button to Lock and Arm
the System. The Lock Icon is displayed on the LCD panel & the
parking lights flash once.
When Armed, Press the Disarm/Unlock button to
Unlock and Disarm the System. The Unlock Icon is displayed
on the LCD panel & the parking lights flash twice.
When the Key Icon Button Has Been Operated for 3 seconds
the trunk open icon will flash on the LED Screen. If text mode
was selected, the words Trunk Open will appear and remain
on the screen until the trunk is shut.
When the Key Icon Button is pressed 2 times in succession
The three puffs of smoke are displayed on the LCD screen
while the vehicle is running. The exhaust indication will flash
and the hour glass will indicate count down timer based on the
5, 10, 15, or 20 minute run time set up by your installation
center. When the unit shuts off the exhaust indication will turn off and the transmit-
ter will play a melody.
Note: Engine can be started in many modes armed, disarmed, valet, etc... The
screen shown is Locked/Armed and running.

128-8549
15 of 24
Page15
When the Panic Mode has been activated and the
system is armed the vehicle's lights will flash, the
siren and lock icon will be displayed on the LCD
screen and the siren will beep. If the system is
disarmed and the Panic Mode is activated, the lights will flash unlock icon will
be displayed and the siren will beep on the LCD screen.
When ever the vehicle is operated from the two way transmitter,
the unit will beep responsive to the function executed at the
vehicle. 1 beep when armed, 2 beeps when disarmed, etc... at
times It may be inconvenient or too noisy to hear the beep tones,
so the system allows you to set the unit for vibrate mode. To
toggle on or off beep tones/vibrate, Simultaneously press the "F"
and unlock buttons. The icons shown left will appear in the upper
left hand corner of the screen to indicate vibrate..
If the alarm system has been triggered, the icon displayed on the transmitter
LCD will indicate which zone has been activated, as well sound the beep
tones, or vibrate dependent upon the setting as shown above. The following
trigger patterns will be displayed.
Triggered and the entry attempt was made to one of the
vehicle Doors.
Triggered and entry attempt was made to the vehicles Hood
or
Trunk.
Triggered and entry attempt was made to the vehicles glass, or
the vehicle has been hit or bumped hard enough to cause a
response from the vibration detector.
ADDITIONALICONSTHATMAYBEDISPLAYEDARE:
If the arm/disarm chirp tones have been turned off at the vehicle,
when you arm, or disarm, the display will indicate this as shown
and there will be no arm/disarm chirps at the transmitter. This is
true if the transmitter is set for vibrate mode.

128-8549
16 of 24
Page16
When the vehicle is armed, and a door is opened, or ajar, the transmitter will
chirp 3 times, the lights will flash, and the display will indicate a door trigger as
shown on the previous page. When the door is closed or the zone clears, the
transmitter will chirp 1 time, and the display will clear.
When the vehicle is armed, and the hood or trunk, is opened or ajar, the trans-
mitter will chirp 3 times, the lights will flash, and the display will indicate a hood
or trunk trigger as shown on the previous page. When the hood or trunk is
closed, or the zone clears, the transmitter will chirp 1 time, and the display will
clear.

128-8549
17 of 24
Page17
ADDITIONALREMOTEFEATURES:
The two way remote control unit allows you to access status
information from the vehicle, check temperature, light the
display, toggle the transmitter from beep tones to vibrate mode,
initiate daily start timer, and temperature start. Selection of
these and other features are shown below:
NOTE: Transmitter must be within operating range of the
vehicle, approximately 1000 ft.
Check Vehicle Status:
Press the lock+key+option buttons simultaneously for 1
second. The vehicle's alarm will display the systems current
status.
Check Temperature: (Only available on certain remote start units)
Press the option+key buttons simultaneously for 1 second.
The vehicle's alarm will display the temperature. Temperature
is read from the alarm's module located below the dashboard. This reading
may be higher than actual ambient temperature due to the greenhouse and is
relative only to the inside vehicle temperature.
Temperature Start Mode: (Available on certain models)
To toggle this feature on or off, from the armed mode, press the Option &
Unlock Buttons simultaneously, the temperature icon appear on, or
disappear from the display, and the transmitter will emit a tone.
NOTE: This feature must be active in the feature selection menu of your system.
Check with your installing dealer to insure this feature is set to the on position.
Light The Display:
Press and release the "F" (Function) button one time. The display will illumi-
nate for 10 seconds.
Vibrate Or Tones:
Press the "F" and unlock buttons simultaneously to toggle this feature on and
off.
Daily Start Timer: (Only available on certain remote start units)
24 Hour Start Timer. Standing at the vehicle at the time you want it to
start, press the option + lock buttons simultaneously for 1 seconds. The
transmitter will beep and display the 24 hr timer. This is the time the vehicle will
start when you follow the exit procedure. In other words, if you want the vehicle
to start 6AM, at 6AM of any morning, standing at the vehicle, press and hold the
option + lock buttons until you hear a beep and the 24 hr timer is displayed.
This establishes a starting time. The unit will start at the prescribed time once
only. This function must be selected each time you want the vehicle to start. To
activate this function, (a) Turn the ignition switch off. (b) Within 10 seconds of
step (a), depress and hold the brake pedal, while pressing the key icon
transmitter button 2 times. (c) the unit will emit 2 chirps, the transmitter will beep
and the start timer icon on the display will remain on. The vehicle will start at the

128-8549
18 of 24
Page18
set time. To toggle this feature off, press the option + lock buttons simulta-
neously until a beep is heard and the 24 hr timer turns off.
Note: the unit will start once and run for the prescribed time. If you require more
frequent starting please refer to auto start up timer mode shown earlier in this
guide.
NOTE: To insure accurate 24 Hour Start up, it is advisable to reset the start time
periodically as time may drift slightly each day.
TimingCountDown:
The unit offers an additional count down timer for situations where an
alert tone may be needed to remind you of something important. For
instance you may have a meeting 4 hours from now and you want a
reminder in 3 Hrs and 45 Mins. This additional count down timer allows
you to set the count down up 19 Hours and 59 Minutes from the current time
and when the timer reaches zero, the transmitter will emit a tone or vibrate
dependent on your preferred setting. See chart for setting the count down time
for this feature.
Valet:
When the System is in the valet mode, the icon shown will show
in the display when the status check buttons are activated.
Parking Meter Counter:
The transmitter has a built in clock that can count down from 10, 20, 30, 60, 90,
or 120 minutes. This feature is useful when parking the vehicle in a metered
parking lot. If the time on the parking meter is 30 minutes, you can set the
count down timer to 20 minutes. The transmitter will emit a beep tone when
the timer expires to remind you to get back to your vehicle. See following chart
for setting the parking meter count down timer feature.
Alarm Clock Mode:
The transmitter has a built in alarm clock that can be set to beep at a
certain time each day. The alarm clock mode must be set, and the
feature turned on. To use this feature please refer to the chart on the
following page.
NOTE: Your system is shipped with two transmitters, 1 two way,
shown on the left and the one way transmitter, shown right. The one and two
way transmitters are programmed from the factory with separate
lock & unlock buttons, the trunk/key icon button operates remote
start and remote trunk release where applicable. The
option button and any button combination may be
programmed to operate various options. Consult your
installation center for button programming and
options that may have been added to your vehicle.
Although this is the default programming from the
factory, this can be changed for you to any configura-
tion you prefer. Please refer to the transmitter pro-
gram guides included with your kit.
NOTE: A maximum of two of either style transmitter may be
programmed to your unit.
Battery Indicator: Your transmitter has a battery indicator that is
shown in the upper right

128-8549
19 of 24
Page19
corner of the screen as shown left. This icon indicates a new battery
shown with 3 bars. As the battery deteriorates, the bars will disappear. 1
bar indicates the battery should be replaced. Replace battery with a fresh
1.5VAAA battery and dispose of the used battery properly.
Other icons that will be displayed at times when certain functions and features
are active in the vehicle or on the remote:
Range Indicator. The range indicator will have bars to the side of the
icon if the unit is out of range.
Vibrate Mode On, this icon will be displayed if you select vibrate instead
of tones. To toggle vibrate on and off, press "F" + Unlock simultaneously.
Alarm Clock. This icon will be toggled on and off when the "F" + Trunk/
Key buttons are pressed simultaneously. The feature must be set in the
feature selection menu of the transmitter.
TimingCountDown:
The unit offers an additional count down timer for situations where an
alert tone may be needed to remind you of something important. Setting
information shown on previous page.
Power Save Feature. Press the "F" and Lock buttons simultaneously to
toggle this feature on and off. With this mode on, the battery in the
transmitter will go into a power down mode when the unit is disarmed.
24 Hour Start Timer. Standing at the vehicle at the time you want it to
start, press the option + lock buttons simultaneously for 1 seconds. The
transmitter will beep and display the 24 hr timer. This is the time the
vehicle will start when you follow the exit procedure. In other words, if you want
the vehicle to start 6AM, at 6AM of any morning, standing at the vehicle, press
and hold the option + lock buttons until you hear a beep and the 24 hr timer is
displayed. This establishes a starting time. The unit will start at the prescribed
time once only. This function must be selected each time you want the vehicle to
start. To activate this function, (a) Turn the ignition switch off. (b) Within 10
seconds of step (a), depress and hold the brake pedal, while pressing the key
icon transmitter button 2 times. (c) the unit will emit 2 chirps, the transmitter will
beep and the start timer icon on the display will remain on. The vehicle will start
at the set time. To toggle this feature off, press the option + lock buttons
simultaneously until a beep is heard and the 24 hr timer turns off.
Temperature Start Mode. This icon will appear when the temp start
mode is activated. The vehicle will start one time automatically when the
temperature reaches 0*. Caution, Be certain vehicle is outside before
activating this mode. To toggle this feature on of off, from the Locked/
Armed mode, press the Option and Lock buttons simultaneously. (Available on
certain remote start models only).
Throughout this manual you will find screen shots where they apply if using the
two way transmitter. If using the one way transmitter while the two way transmit-
ter is within range of the vehicle, the two way transmitter will update it's screen.

128-8549
20 of 24
Page20
THISPAGELEFTBLANK INTENTIONALLY