Audiovox Pursuit PRO 9445FT User manual

Model PRO 9445FT
Owner's Manual
Remote Keyless Entry
Congratulations on your purchase of this state-of-the-art automotive
convenience system. To fully appreciate the many functions incorporated in
this system, please take a few moments to read this manual.
FEATURES AND AVAILABLE OPTIONS:
User Programmable Transmitters Offer Over 16 Million Different
Codes
Instant Locking and Unlocking of the doors via a Remote Keychain
Transmitter
Vehicle's Starter is disabled whenever the doors are locked using the
Transmitter
Programmable Active or Passive Starter Interrupt Operation
Programmable Auto Lock / Unlock via ignition key
Optional interior illumination when the doors are unlocked using the
Transmitter
TheOption Button on the KeychainTransmittercan beused toactivate
any of the following optional devices;
* Trunk Release relay
* Remote Car Starter
* Window up or down module
* Garage Door Interface
AMARK WILL APPEAR IN THE BOX TO THE LEFT OF THE
OPTIONAL FEATURE IF IT HAS BEEN ACTIVATED IN YOUR SYSTEM.
Passive Operation
Auto Lock & Unlock from ignition key
Optional Interior Illumination Relay
Starter interrupt
Channel 2 Optional Accessory

REMOTE DOOR LOCKING:
1. Turn off the engine, exit the vehicle, and close all doors.
2. Press and release the Lock/Unlock button on the keychain transmitter.
The vehicle's doors will lock.
3. The vehicle'sstarter is now interrupted,and the car cannotbe started, even
when using the ignition key.
BACK UP PASSIVE OPERATION:
The system can be programmed to operate automatically when you leave the
car. This programming must be done by the installer during the installation.
The Passive feature works as follows;
1. Turn off the engine, exit the vehicle, and close all doors.
2. In 30 seconds, the vehicle's starter will automatically be interrupted. If the
passive lock feature was selected on at time of installation, then the doors
will lock automatically in 30 seconds.
OPTION NOTE: The system can be programmed to either...
Automatically lock the doors, or only lock the doors when the transmitter is
operated. Check with your installation center for programming of this feature.
REMOTE DOOR UNLOCKING:
1. As you approach the vehicle, press and release Lock/Unlock button on the
keychain transmitter.
2. The vehicle's doors will unlock, and the starter interrupt system is
disengaged allowing you to start the vehicle.
3. Never attempt to unlock the doors from a distance that will prevent you
from starting the vehicle within 30 seconds if the system has been
programmed for passive operation. If you do this, and the vehicle will not
start, simply press and release the lock/unlock button again.
OPTION NOTE: If the optional interior illumination relay has been
installed in your vehicle, then the dome light will turn on for 30 seconds
during step 1 above. If you turn the ignition switch on during the 30
second timer, then the dome light will turn off.
2

CHANNEL 2 OUTPUT:
The system has an additional output that can be wired to a number of different
optional accessories. Some examples of these optional accessories are;
– Remote Trunk Release
– Remote Car Starter
– Remote Window Roll Up
To activate the optional accessory;
1. Press and hold the "Option" button on the keychain transmitter for
approximately 3 seconds.
2. The optional accessory that has been connected to channel 2 will now
engage.
AUTO LOCK & UNLOCK:
The system can be programmed for automatic lock when the ignition switch
is turned on and for automatic unlock when the ignition switch is turned off.
When this feature is activated, approximately 3 seconds after turning the
ignition key to the on position, all doors will lock only if all doors are closed.
When the key is turned to the off position, all doors will immediately unlock.
VALET SYSTEM OVERRIDE SWITCH:
The "valet" switch allows you to temporarily by-pass the starter interrupt
feature, eliminating the need to hand your keychain transmitter to parking
attendants or garage mechanics. When the systemis in valetmode, all features
except the starter interrupt will remain operational. To use the valet mode;
1. Enter the vehicle, and turn the ignition key to the on position.
2. Move the valet toggle switch to the on position.
3. To return to normal operation, move the valet switch to the off position any
time the ignition key is on.
In the event that you lose your transmitter, or if the transmitter fails to operate
when you return to the vehicle, the valet switch can be used as a system
override switch. Turn the ignition key on, and move the valet switch to the on
position. The vehicle can now be started.
NOTE: Always remember to move the valet switch back to the off
position. This will ensure that the vehicle remains protected at all
times.
3

PROGRAMMING NEW OR ADDITIONAL TRANSMITTERS:
The system can be programmed to accept the codes from 4 different
transmitters. To program transmitters, it is always best to have all transmitters
that will operate the system with you during the programming. To program the
transmitters, be sure to follow all steps in exact order, and do not wait more
that 10 seconds between any 2 steps.
1. Turn the ignition key to the on position.
2. Move the valet switch on, off, on, off, on, then off.
If the optional illuminated entry feature has been installed, the dome
light will flash one time.
3. Press and hold the "Lock/Unlock" button on the first transmitter for
4 seconds.
If the optional illuminated entry feature has been installed, the dome
light will turn on for approximately 1.5 seconds when the transmitter
is accepted.
4. Repeat step 3 for all transmitters up to a total of four.
5. Move the valet switch on then off.
If the optional illuminated entry feature has been installed, the dome
light will flash two times.
6. Press and hold the "Option" button on the first transmitter for 4 seconds.
If the optional illuminated entry feature has been installed, the dome
light will turn on for approximately 1.5 seconds when the transmitter
is accepted.
7. Repeat step 6 for all transmitters up to a total of four.
8. Turn the ignition key off, and test all transmitters.
9. If any transmitter is not working, repeat the entire procedure.
TRANSMITTERBATTERY REPLACEMENT
You will notice a decrease in transmitter range as the battery condition
deteriorates. Transmitter battery replacement is recommended at least every
10 to 12 months, depending upon how frequently the transmitter is used.
The transmitter has a small red L.E.D. built into the case. This L.E.D. can be
used to indicate battery condition. If the L.E.D. does not illuminate, then the
4

battery is discharged, and must be replaced.
To replace the transmitter battery,
1. Remove the small phillips head screws from the bottom cover of the
transmitter.
2. Carefully unsnap the top cover of the transmitter from the bottom cover.
3. Remove the discharged battery, making note of the location of the + and
– contacts, and replace with a new type GP 27A 12 volt battery.
4. Replace the transmitter cover, taking care not to damage the L.E.D. or
switches on the circuit board, and secure with the small phillips head screw.
5
© 1998 Audiovox Corporation, Hauppauge, N.Y. 11788 1-800-645-4994
128-5392

ORDER FORM FOR 2 BUTTON TRANSMITTER
MODEL NO. PRO OE2 w/ PD-21
IMPORTANT : To help us expedite your order, please print all of the information legibly,
and mail this form and your payment according to the instructions below.
1. Name : ___________________________________________________________
Address : ___________________________________________________________
City : _____________________ State : _______ Zip Code : __________________
2. Telephone Number : ( _______ ) ______________________________________
3. Enter the total number of transmitters required here : ______________________
4. The cost per transmitter is $ 65.00.
5. Enter the total amount enclosed here : __________________________________
( New York state residents must include the appropriate sales tax.)
6. Method of payment; check one of the boxes below.
Mastercard Visa Check or money order*(donotsend cash )
* Make checks payable to Audiovox Corporation
7. Credit Card Number : ________________________________________________
8. Credit Card Expiration Date : _____________________
Credit card purchasers can order additional or replacement transmitters by
phone. Simply dial 1 - 800 - 645 - 4994, and follow the instructions from the
operator interface.
9. Mail this form, and your check, to ;
Audiovox Corporation
150 Marcus Blvd.
Hauppauge, N.Y., 11788
Attn. : TRANSMITTER DEPARTMENT