AUSTRAL CLOTHES HOISTS RetractAway 40 User manual

RetractAway 40 & RetractAway 50
Your Austral RetractAway clothesline is designed to last a long time. It is important to follow these
instructions so you will enjoy the benefits of a properly installed clothesline. Incorrect installation or
operation could damage your line and/or void your guarantee. If at any time your clothesline fails to
function correctly or if spare parts are required then call your state distributor listed on the Warranty page.
SITE SELECTION & MOUNTING OPTION
Select a suitable site and mounting option
for your RetractAway.
The maximum span between the two
mounting surfaces should not exceed 8
metres for a RetractAway 40 or 10m for a
RetractAway 50.
Minimum extension for RetractAway 40 or
50 is 2m.
Allow a minimum of 500mm clearance
(ideally 1 meter or more) on the sides for
ease of use and for clothes to blow about.
See Figures 1and 2.
*A Socket will be required if the Post is to be
removable.
tWall fixings are not supplied as
mounting surfaces vary.
For brick or block fixing use 8mm masonry
anchors.
For timber fixing use 8mm coach screws.
Please seek advice if fixing to alternative
surfaces.
Support battens may be required to mount
on some surfaces, timber fences,
weatherboard, fibro, blueboard etc.
1/4
Fig 1
Cabinet
1
1
1
1
Wall Fixings
t
4t
2t
2t
-
Posts
-
1
1
2
Mount Bar
-
-
1
1
Socket *
- *
1 *
- *
1 *
AUSTRAL CLOTHES HOISTS PTY. LTD.
INCORPORATED IN VICTORIA A.B.N.: 68 006 790 727
222-224 HAMMOND ROAD, DANDENONG 3175, AUSTRALIA
Tel: [phone], Fax: [phone]
International Tel: [phone]
International Fax: [phone]
W: www.australclotheshoists.com.au
E: [e-mail]
IMPORTANT
There is considerable stored energy in the RetractAway at all times.
UNDER NO CIRCUMSTANCES REMOVE ANY SCREWS AT EITHER END OF THE UNIT,
NOR ALLOW THE DRAW ARM TO RETURN UNASSISTED TO THE UNIT.

CORD HEIGHT
Due to distance that
RetractAway can cover
and weight of wet
clothing, lines may sag
in middle. To allow for
this sag, RetractAway
cabinet & Catch should
be mounted so that
cord is at least 100mm
above user’s head
height. For long spans,
particularly
RetractAway 50,
consider increasing this
height. See Figure 3.
INSTALLATION STEPS
Wall to Wall
Parts required: 1x RetractAway Cabinet & 4x wall fixings
Follow Steps For: - Mount RetractAway to wall
- Mount Receiving Catch to wall
- LINE TENSIONING
Wall to Post
Parts required: 1x RetractAway Cabinet, 1x Post, 1x Socket & 2x wall fixings
Follow Steps For: - Mount RetractAway to wall
- Mount Receiving Catch to Post
- POST INSTALL (into soil OR with Ground Socket)
- LINE TENSIONING
Post to Wall
Parts required: 1x RetractAway Cabinet, 1x Post, 1x Mounting Bar & 2x wall fixings
Follow Steps For: - Mount Cabinet to Post
- POST INSTALL (into soil OR with Ground Socket)
- Mount Receiving Catch to wall
- LINE TENSIONING
Post to Post
Note: Maximum recommended extension for Post to Post is 6.5m
Parts required: 1x RetractAway Cabinet, 2x Posts, 1x Mounting Bar & 1x Socket
Follow Steps For: - Mount Cabinet to Post
- Mount Receiving Catch to
Post - POST INSTALL (into soil OR
with Ground Socket)
- LINE TENSIONING
Mount RetractAway to wall
Position RetractaAway Cabinet on wall so that mounting slots on either
side are approximately 100mm above the users head height. Ensure
Cabinet is level. Mark wall through both slots. Drill a hole on each mark
to suit the fasteners. Fix RetractAway Cabinet to wall ensuring washers
supplied with Cabinet are between the heads of the fasteners and the
slots. See Figure 4. 2/4

Mount Receiving Catch to wall
Place the Receiving Catch against the wall opposite the Cabinet, ensure the Catch is centred to the Cabinet.
Position the top of the Catch 100mm above the users head height. See Figure 3a.
Ensure the Catch is level. Mark the wall through both holes. Using the marks, drill two holes to suit fasteners. Fix
Catch to wall using the remaining fasteners.
Mount Receiving Catch to Post
Fix Receiving Catch to Post with 8x65mm bolts supplied with Post. Fit black plastic End Cap to top of Post.
Mount Cabinet to Post
The Mounting Bar has nuts and bolts provided inside it. Use the long bolts to fix the Mounting Bar to the Post.
Feed the short bolts through the washers supplied with the Cabinet. Use the short bolts to fix the Cabinet to the
Mounting Bar ensuring washers are between the bolt heads and the slots on the Cabinet. See Figure 4.
POST INSTALL
Please note:
Austral cannot guarantee the stability of RetractAway Post installations due to soil variances. Please seek advice
prior to Post installations to ensure appropriate footings are used. Consideration should be given to larger concrete
footing to increase Post stability for some soil types (i.e. sandy, loose or un-compacted soils etc.).
Measure out the distance you want the Post to be at. See Figure 2for minimum and max distances. Ensure this
position is centred to where the other end of the clothesline is / will be. Mark the position on the ground, this will be
the centre of the hole.
Hints & Tips
Rocks or chunks of concrete may be placed in the hole around the Post/Socket to hold it in position while the
concrete sets. The rocks should be large enough for concrete mix to flow through the gaps.
For sandy, loose or shifting ground you should consider a larger concrete footing to increase Post stability. To do
this simply dig a larger hole, perhaps 250mm diameter by 700mm deep. It will require more concrete. Use large
rocks to keep Post at desired height. See Figure 5c. Mix & Pour Concrete
3/4
Install Post into soil
Install Post with Ground Socket
Dig a hole 200mm in diameter and deep enough
so that when the Post is stood upright in the
hole, the top of the Cabinet / Receiving Catch
will be 100mm above the user’s head height.
See figure 3b. For a standard clothesline height
of 1800mm high, put 480mm of post in the
ground. See Figure 5b. Hint: Poor drainage
around Post (ie soil type is clay or Post is
installed at bottom of a slope) increases water
exposure & chance of rusting. Increase
drainage by adding gravel under Post as shown
for Socket install in Fig 5a.
Dig a hole 200mm in diameter & 560mm deep. Fill hole with
gravel (approx. 100mm) until top lip of Socket sits just above
ground level. See Figure 5a. Remove Socket from hole. The
Socket has 5 holes on its side, there is a Pin provided to go
through these holes. Use Figure 5a to determine the best
hole. Use a hammer to tap Pin through selected hole. Put
Socket back in hole. Insert Post into Socket (after installation,
cover the Socket with the Socket Cap whenever the Post is
removed. Keep the Socket Cap in a convenient location ie
hang it off the clothesline). Add a further 50mm of gravel into
the hole around the sides of the Socket (this is for drainage).
IF DIGGING IS REQUIRED, ENSURE IT IS SAFE TO DO SO

1. Mix concrete in the ratio of 4 gravel, 2 sand and 1 cement or simply use premixed concrete packs. To hold the
Post/Socket erect, the concrete must be mixed fairly dry but should still be wet enough that it sticks to itself when
squeezed in the hand, it should not crumble.
2. Place the Post / Socket (with Post in it) in the hole. Ensure the Cabinet and/or Receiving Catch is facing the
right way. Pour concrete to within 20mm from the top of the hole (finished ground level). See Figure 5d. Check the
Post is plumb/vertical using a spirit level. Use a crowbar or similar to ram the concrete tight so it holds the
Post/Socket in place. If the concrete has dropped below 20mm, top up with more concrete, check vertical and ram
tight again. Fill last 20mm of hole with soil, press soil down gently with the sole of your shoe. Check vertical one
last time. Now leave the concrete to set. DO NOT USE FOR 48 HOURS.
LINE TENSIONING
If Posts have been installed ensure concrete is set and dry
before tensioning the lines. Extend the Draw Arm to the
Receiving Catch. Flick the Line Tension Lock to the locked
position at the Cabinet. Turn the Tension Knob a click or 2 in a
clockwise direction. See Figure 4. Starting on the middle line,
uncleat the cord then pull the loose end to take up the slack.
See Figure 6a. Recleat the cord and fit it back into the Cord
Tidy. See Figure 6b. Repeat for the 2 outside lines then the
remaining 2 lines. Tension one cord at a time and ensure it is
recleated and back in the Cord Tidy before starting another.
After all lines have been tensioned, snip off excess cord allowing a
20mm tail. See Figure 6b.
RETRACTING THE CORD
Switch the Line Tension Lock to the unlocked position before
retracting the Cord back into the Cabinet, this ensures minimum
wear on internal gears. If there is a lot of tension on the Cord,
the Lock may be harder to move. To make it easier, take tension
off the Lock by turning the Tension Knob clockwise a little with
the right hand. Whilst doing this, switch the Lock to the unlocked
position with your the left hand. Then, unhook the Draw Arm
from the Catch and slowly guide the Cord and Draw Arm back
into the Cabinet.
MAINTENANCE & TIPS
-Occasionally check all nuts and bolts for tightness.
-Keep the Cap on the Ground Socket whenever the Post is removed.
-Re-tension Cords occasionally as required.
WARRANTY
Please see separate page for Austral’s Warranty.

4/4