Jeld-wen Svc001 User manual

Installation Instructions

for Builders Vinyl Sliding Patio Door Handing Reversal (SVC001)

IMPORTANT INFORMATION

These instructions are only applicable to pre-installed 6'8" and 6'10"

Builders sliding patio doors without blinds between the glass that

have weep holes on the top and bottom. Certain grid/bar patterns are

not reversible. Only these doors are reversible, or specially designed to

be converted to be opened either from the left or the right. Patio doors

that are set up for left hand operation (door opens from the left on the

exterior) or vice versa, can be converted to open from the opposite side

with these instructions. DO NOT install the patio door until after

completion of these instructions and the xed panel is on the

desired side. If any of the above conditions represent a concern, or if you

expect environmental conditions to exceed the patio doors performance

rating, DO NOT install the patio door. Contact your local dealer or

distributor for recommendations.

For questions, feel free to contact us by phone or email:

• Phone: 1-(800)-JELD-WEN/1-(800)-535-3936

• Email: [email protected]

Precautions and Safety

• Follow all manufacturers’ instructions and labels.

• Use proper and safe equipment and precautions if servicing the exterior

side of patio doors above ground level.

• Insect screens are not security devices and will not prevent children,

other people, or pets from falling through.

• Use extra care when driving screws near glass unit to avoid breakage.

REMOVE SCREEN

1. Using a phillips

screwdriver, turn

(DO NOT remove)

adjustment screws

counterclockwise

to retract rollers in

eachcorner.

• Use caution when tightening screws to avoid stripping the screwholes.

• Handling patio door parts can be awkward and heavy and could

cause physical injury or product damage; we recommend the help of a

second person.

Needed Tools and Materials

• Pliers

• Rubber mallet

• Putty knife

• Pencil

• Flat head screwdriver

• Phillips head screwdriver

• Power drill with 3/32" drill bit for

pilot holes only

Prepare Patio Door

• Move patio door to installation location.

• Remove all wrapping material, shipping blocks and handles.

2. Lift screen up and over

bottom screen track (if

needed, insert a large

putty knife between the

track and the rollers to

help lift over thetrack).

NOTE: DO NOT damage

track when removing;

this may result in poor

screen operation.

3. Grip one end of the

screen track with pliers

and lift up carefully

to remove.

Attachment

screw

Adjustment

screw

Operating

panel track

Anti-lift

block

Dust

plug

Lock

hook

Handle

lever

Interior

handle

Exterior

handle

Attachment

screws

Installation Instructions

for Builders Vinyl Sliding Patio Door Handing Reversal (SVC001)

TITLE 1

6. Pull hook out to locked position with ngers or pliers. Maintain grip

on latch hook to keep lock from falling inside stile.

7. Remove both phillips screws to remove lock.

8. Remove and turn lock over and reinstall with hook facing the

opposite direction.

9. Reinstall the handle lever on the interior and then both handles.

3. From the interior, lift

panel bottom up and

over sill track and pull

inward (if needed,

insert a large putty

knife between the track

and the rollers to help

lift over thetrack).

NOTE: DO NOT damage

track or metal track cover

when removing track; this may result in poor operation.

4. Grip one end of the

operating panel track

with pliers and lift up

carefully to remove.

REMOVE OPERATING PANEL

1. Completely open operating panel to clear anti-lifts in the header.

2. Roller adjustment

screws are at both

bottom ends of the

panel. With a Phillips

screwdriver, turn

the bottom screw

counterclockwise to

retract rollers and lower

the panel.

5. Pry both anti-lifts from

header with at head

screwdriver.

6. Flip frame (top

tobottom).

7. Gently pry out the

frame dust plugs

in both ends of the

sill with at head

screwdriver and

install these in the

corresponding holes in

the head jamb.

SWITCH ROLLERS AND LOCK

1. Lay the panel on a at padded surface.

2. Remove attachment screw (top screw on each roller) from the roller

on each end of the panel and remove.

3. At other end of panel, pry the dust plugs from roller screw holes

with at head screwdriver. Install both rollers on the opposite end of

thepanel.

4. At opposite end, install dust plugs (two at each end with 1/2" in large

holes and 1/4" in small holes) into previous roller screw holes.

5. If the handle is pre-

installed, remove the 2"

machine screws from

interior handle set and

remove both handles

and handlelever.

NOTE: Step 6 must be

performed with the

panel in a horizontal

position to keep the lock

reinforcement bar from

falling down inside the

panel.

Keeper

Jamb

3/8"

Interior

side

Installation Instructions

for Builders Vinyl Sliding Patio Door Handing Reversal (SVC001)

INSTALL OPERATING PANEL

6. Test operation by closing and locking operating panel. If door does

not lock tightly, loosen screws, adjust keeper up or down, then

retighten.

7. When the lock operates correctly, mark and drill 3/32" pilot holes in

the remaining two holes and secure with screws.

8. Wipe off marks (pencil will easily wipe off vinyl).

2. Place operating panel next to the door in an open position. Lift the

panel, place the top into the operating panel track in the head and

swing the bottom over the sill and rest the rollers on the track.

3. Adjust rollers until the panel just clears the track.

4. Install security anti-lifts with at section facing the exterior into the

operating panel track in header so they will be above the operating

panel when it is closed.

1. Starting at one end,

press the panel track

with the higher side

toward the interior,

into the sill until it

snaps into place.

NOTE: Install panel

with latch hook

pointing upward and

facing the keeper in

the side jamb, and

the interlock facing the xed panel.

ALIGN LOCK KEEPER

1. Mark jamb at top of

keeper with a pencil.

2. Unscrew and

removekeeper.

3. Mark another line

3/8" below previously

marked line.

4. Mark the center of the

slotted holes and drill

3/32" pilot holes.

5. Install keeper with top

at lower pencilmark.

Screen track

“nub”

Installation Instructions

for Builders Vinyl Sliding Patio Door Handing Reversal (SVC001)

©2021 JELD-WEN, Inc. This publication and its contents are owned by or licensed to JELD-WEN, Inc. or its afliates or third parties, and are protected by copyright, trademark, and other laws. Unauthorized use

or duplication is prohibited. JELD-WEN reserves the right to change product specications without notice. Please visit our website at jeld-wen.com for current information.

Please visit jeld-wen.com for warranty

and care and maintenance information.

Thank you for choosing

SVC001 10/21

FINISH CONVERSION

2. Tap the ller into the

groove at the new

top of the frame with

a rubber mallet (this

will cover former

weep holes).

3. Reinstall screen track

with “nub” facing the

interior.

4. Position top of screen

into top channel.

5. Lift bottom up and over onto track.

6. Extend all four rollers by turning adjustment screws clockwise until

the screen is level and a slight pressure is felt.

7. The patio door is now ready for installation.

1. On the exterior, now

the bottom, look for

a groove ller (a long,

thin vinyl strip that

ts into a groove in

the frame). If a groove

ller is present, lift one

end with a at head

screwdriver and pull

out to remove.

The information contained herein is provided solely for informational and/or educational purposes. JELD-WEN disclaims any and all liability associated with the use

and/or provision of this information. Any reliance upon the information or advice is at the risk of the party so relying. The information contained herein may be

changed from time to time without notication.

Other Jeld-Wen Household Appliance manuals