AUSTRALIAN MONITOR SYNERGY2 User manual

SYNERGY2SERIES
Two Channel Power Amplifiers
Drawing on the heritage of Australian Monitor’s low impedance amplifier design comes the latest in low impedance
amplifiers from the Australian Monitor Pro series, the Synergy2. The Synergy2 series offers an impressive range of
highly powerful 2 ohm rated amplifiers in rugged yet stylish 2 RU chassis. Available in three powerful models the SY2200
will deliver 600W, the SY2400 will deliver 1100W and the SY2700 will deliver 2000W. All models also offer on board clip
limiting, ground lift switching, XLR ins and binding post and 4 pole speaker connector outputs. As with all Australian
Monitor Pro Series amplifiers they deliver the sonic clarity you’ve come to expect from an AM amp.
>3 models
>All 2 ohm capable
>SY2200 2 x 110W into 8 ohm, 2 x 200W into 4 ohm, 2 x 300W into 2 ohm
>SY2400 2 x 190W into 8 ohm, 2 x 350W into 4 ohm, 2 x 525W into 2 ohm
>SY2700 2 x 400W into 8 ohm, 2 x 700W into 4 ohm, 2 x 1000W into 2 ohm
>On board clip limiter
>Ground lift switch
>XLR in and link (male/female)
>Binding post/4 pole speaker connector outs
At a Glance

Output Power
Voltage Gain
Thermal Dissipation
Current Draw
Dimensions (H x W x D)
Unit Weight
Shipping Weight
Shipping Dimensions (H x W x D)
Common Specifications (To all SY2 Amplifiers)
Distortion (re: 4ohm, 1dB below clip)
THD (@ 1kHz)
<0.02% IMD SMPTE (60Hz : 7kHz 4:1)
<0.03%
Input Impedance 20kohms
Input Sensitivity 1Vrms
Input CMRR >80dB
Signal/Noise Ratio A-Weighted
>104dB
Crosstalk >70dB
Slew rate >40 V/µsec
Damping factor (@ 1kHz re 8 ohms)
> 375:1
Frequency response (+/-3dB)
15 Hz- 50 kHz
Indicators Power, Status (L/R), Overload, Thermal, Fault
300W 0.1% THD @ 1kHz
28.3 (29dB)
Both channels driven, 2ohm load
1/8th power
425W (1450btu/hr)
Both channels driven, 2ohm load, 230Vac
1/8th power
2.7A
87mm x 482mm x 400mm
12.5kg
14 Kg
210mm x 540mm x 540mm
525W 0.1% THD @ 1kHz
37.4 (31dB)
Both channels driven, 2ohm load
1/8th power
780W (2661btu/hr)
Both channels driven, 2ohm load, 230Vac
1/8th power
5.0A
87mm x 482mm x 400mm
15.5kg
17 Kg
210mm x 540mm x 540mm
1000W 0.1% THD @ 1kHz
52.9 (34dB)
Both channels driven, 2ohm load
1/8th power
1410W (4811btu/hr)
Both channels driven, 2ohm load, 230Vac
1/8th power
9.1A
87mm x 482mm x 455mm
17.5kg
19 Kg
210mm x 540mm x 575mm
Model SY 2200 SY 2400 SY 2700
NSW Tel: [phone] Fax: [phone]
VIC Tel: [phone] Fax: [phone]
QLD Tel: [phone] Fax: [phone]
SA Tel: [phone] Fax: [phone]
WA Tel: [phone] Fax: [phone]
NZ Tel: [phone] Fax: [phone]
ENGINEERED AND DISTRIBUTED BY AUSTRALIAN MONITOR ABN 78 001 345 482
149 Beaconsfield Street, Silverwater Sydney NSW 2128 Australia
SYNERGY2SERIES
Architectural Specifications
The amplifier shall be of 2 channel low impedance design, of sturdy construction and shall be 2 rack units high. The amplifier
shall have on board clip limiting, ground lift switching, XLR inputs and 4 pole speaker connector and binding post outputs.
Front panel level controls will be provided as well as status, overload, thermal, power and fault indication. The amplifier will
be capable of 2 ohm operation and shall have overload, output short circuit, thermal and output DC protection as well as a
slow start facility. The amplifier shall be an Australian Monitor Synergy2 series.