AUSTRALIAN MONITOR AM-Tone1 User manual

AM-TONE1
INSTALLATION AND OPERATION MANUAL
SYDNEY
(NSW & ACT SALES)
149 Beaconsfield
Street Silverwater
NSW 2128
Private Bag 149
Silverwater NSW 1811
Phone: [phone]
Fax: [phone]
Email:
[e-mail]
MELBOURNE
(VIC & TAS SALES)
22/277
Middleborough Road
Box Hill VIC 3128
PO Box 151 Blackburn
South VIC 3130
Phone: [phone]
Fax: [phone]
Email:
[e-mail]
BRISBANE
(QLD SALES)
42 Commercial Road
Fortitude Valley
QLD 4006
PO Box 871 Fortitude
Valley QLD 4006
Phone: [phone]
Fax: [phone]
Email:
[e-mail]
ADELAIDE
(SA & NT SALES)
31 Walsh Street
Thebarton
SA 5031
PO Box 157
Hindmarsh SA 5007
Phone: [phone]
Fax: [phone]
Email:
[e-mail]
PERTH
(WA SALES)
299 Fitzgerald Street
West Perth WA 6005
PO Box 404
North Perth
WA 6906
Phone: [phone]
Fax: [phone]
Email:
[e-mail]
AUCKLAND
(NZ SALES)
Unit B, 11 Piermark
Drive Albany 1331
New Zealand
PO Box 512
Albany 1331
Phone: [phone]
Fax: [phone]
Email:
[e-mail]
AUSTRALIA AND NEW ZEALAND
www.australianmonitor.com.au
EUROPE / ASIA / MIDDLE EAST
www.australianmonitor.com.au
INTERNATIONAL SALES
149 Beaconsfield Street Silverwater NSW 2128 Australian
Private Bag 149 Silverwater NSW 1811
Phone: [phone]
Fax: [phone]
Email: [e-mail]
USA / SOUTH AMERICA
www.australianmonitor.com
SENNHEISER ELECTRONIC CORPORATION
1 Enterprise Drive
Old Lyme CT 06371 USA
Phone: [phone]
Fax: [phone]
Email: [e-mail]

INSTRUCTIONS
Thank you for choosing an Australian Monitor Installation Series AM-TONE1 tone generator module. The AM-TONE1 generates four
tones. These tones are: Evacuation and Alert Tones, as well as a Bell Tone and a Pre Announce Chime.
The installation of the AM-TONE1 involves access to the inside of the mixer or amplifier. Installation should only be
attempted by a qualified technician. Always turn off AC power and remove the AC power cord before attempting to
access the inside of any Australian Monitor Installation Series mixer or amplifier.
INSTALLATION
Installation into compatible Australian
Monitor Installation Series mixers or
amplifiers is simple. Please follow these
easy illustrations for installation.
OPERATION
The modules can produce four different sounds as follows.
1) “EVAC”: a long continuous repeating tone with a ramped
frequency. Triggered by shorting T1 to Com, the sound will
continue to repeat until the short is released.
2)”Alert”: a short tone burst increasing in volume by 10dB steps
from -50dB to 0dB and repeating at 0dB. Triggered by shorting T2
to Com, the sound will continue to repeat until the short is released.
3) “Chime”: a two note ‘ding-dong’ suitable for paging pre-
announce. Triggered by shorting T3 to Com, it will sound only once
for each time the trigger is activated. Please note: “Chime” must
become completely inactive (see below) before it may be retriggered.
4) “Bell”: a short repeating tone burst with decay and reverb.
Triggered by shorting T4 to Com, the sound will continue to repeat
until the short is released.
The output level may be adjusted by means of trimpot VR1 from
OFF (fully counter clockwise) to Maximum (fully clockwise).
If a Mute module is installed, when any sound is active the output
will be muted.
Note: a sound is active until both the chime has finished
sounding and the trigger is released.
TRIGGER PRIORITY
The triggers are prioritized such that T4 has lowest priority and
T1 has highest priority. If a higher priority trigger is activated whist
a lower priority sound is playing, the sound will finish playing and
then the higher priority sound will take over.
REV A 02/10/06