Autani 1000179-01 User manual

User’s Manual
PSC autaniNet Module
Model Number: 1000179-01
Document Number: 80308
7090 Columbia Gateway Drive, uite 140
Columbia, MD 21046
CONFIDENTIAL AND PROPRIETARY
The information contained in this document is proprietary and confidential information of Autani, LLC. Any use of this information
without the expressed written consent of Autani, LLC is prohibited.

PSC autaniNet Module User’s Manual 1. Description
CONFIDENTIAL AND PROPRIETARY
The information contained in this document is proprietary and confidential information of Autani, LLC. Any use of this
information without the expressed written consent of Autani, LLC is prohibited.
2 of 14
Version Date Changed B Revision Description
1 10-23-2019 MEP Preliminary
Table of Contents
1. Description ............................................................................................................... 3
2. Ordering Information ............................................................................................... 4
3. Specifications........................................................................................................... 4
3.1 Absolute Maximum Ratings ........................................................................................................... 4
3.2 Recommended Operating Conditions ........................................................................................... 4
3.3 Electrical pecifications ................................................................................................................. 5
4. Block Diagram .......................................................................................................... 6
5. Host Interface ........................................................................................................... 7
6. Capabilities ............................................................................................................... 8
7. Connector Pin Assignments ................................................................................... 9
8. Antenna .................................................................................................................. 10
9. Dimensions ............................................................................................................ 11
10. Certifications .......................................................................................................... 12
10.1 FCC – United tates .................................................................................................................... 12
10.2 IC – Canada ................................................................................................................................ 13
11. Handling and Storage ............................................................................................ 14
11.1 Alterations .................................................................................................................................... 14
11.2 Handling ...................................................................................................................................... 14
11.3 torage ........................................................................................................................................ 14

PSC autaniNet Module User’s Manual 1. Description
CONFIDENTIAL AND PROPRIETARY
The information contained in this document is proprietary and confidential information of Autani, LLC. Any use of this
information without the expressed written consent of Autani, LLC is prohibited.
3 of 14
1. Description
The P C autaniNet Module provides a cost-effective RF transceiver for 2.4 GHz IEEE 802.15.4
wireless networks. The P C autaniNet Module is based on the Ember EM358X ystem-on-a-
Chip ( oC) and it has been designed to support larger, denser, sleepier, more mobile, secure,
and resilient wireless networks.
Features:
• Designed for autaniNet wireless networks
• Miniature footprint: 0.940” x 1.120”
• Wire antenna
• 15 RF channels
• Integrated hardware support for Ember development environment
• IF debug port
• AE 128-bit encryption
• Low power consumption
• FCC and IC Certified (pending)
• 512KB Flash Memory
• 64KB RAM
• 32-bit ARM Cortex-M3 microprocessor
• RoH Compliant
• Made in USA

PSC autaniNet Module User’s Manual 2. Ordering Information
CONFIDENTIAL AND PROPRIETARY
The information contained in this document is proprietary and confidential information of Autani, LLC. Any use of this
information without the expressed written consent of Autani, LLC is prohibited.
4 of 14
2. Ordering Information
Part Number Description
1000179-01 P C autaniNet Module
3. Specifications
3.1 Absolute Maximum Ratings
Note: Exceeding the maximum ratings may cause permanent damage to the module.
Parameter Min Max Unit
Power upply Voltage (V
DD
) 2.1 3.6 V
Voltage on any digital pin -0.3 V
DD
+0.3 V
torage Temperature -40 125
o
C
3.2 Recommended Operating Conditions
Note: Operating conditions outside those listed here may cause inappropriate behavior.
Parameter Min T p. Max Unit
Power upply Voltage (V
DD
) 2.5 3.3 3.6 V
Operating Temperature 0 25 70
o
C
Logic Input Low Voltage 0 0.2xV
DD
V
Logic Input High Voltage 0.8xV
DD
V
DD
V
RF Tx Power (Ch11-Ch25) +8 dBm

PSC autaniNet Module User’s Manual 3. Specifications
CONFIDENTIAL AND PROPRIETARY
The information contained in this document is proprietary and confidential information of Autani, LLC. Any use of this
information without the expressed written consent of Autani, LLC is prohibited.
5 of 14
3.3 Electrical Specifications
Parameter Min T p. Max Unit
General Characteristics
RF Frequency Range 2.400 2.480 GHz
Data Rate 250 Kbps
Processor core frequency 12 MHz
Flash Memory 512 KB
RAM 64 KB
Power Consumption
Transmit Mode 45.0 mA
Receive Mode 30.0 mA
Processor Only Mode 8.5 mA
Deep leep Mode 1 uA
Logic Characteristics
Logic Input High 0.8xV
DD
V
DD
V
Logic Input Low 0 0.2xV
DD
V
Logic Output High 0.82xV
DD
V
DD
V
Logic Output Low 0 0.18xV
DD
V
Output ource/ ink Current 4 mA
Output ource/ ink Current for high
current pad: PA6,PA7,PB6,PB7,PC0
8 mA
Logic High Input Current 0.5 uA
Logic Low Input Current -0.5 uA
Input Pull-up Resistance 24 29 34 kΩ
Input Pull-down Resistance 24 29 34 kΩ

PSC autaniNet Module User’s Manual 4. Block Diagram
CONFIDENTIAL AND PROPRIETARY
The information contained in this document is proprietary and confidential information of Autani, LLC. Any use of this
information without the expressed written consent of Autani, LLC is prohibited.
6 of 14
4. Block Diagram

PSC autaniNet Module User’s Manual 5. Host Interface
CONFIDENTIAL AND PROPRIETARY
The information contained in this document is proprietary and confidential information of Autani, LLC. Any use of this
information without the expressed written consent of Autani, LLC is prohibited.
7 of 14
5. Host Interface
The P C autaniNet Module incorporates one Universal Asynchronous Receiver/Transmitter
(UART) interface dedicated to the host for communication to and from the module. Also
available is one General Purpose Input/Output (GPIO) and a WAKE interrupt input used to wake
up the module from low power sleep mode. The GPIO and WAKE interface connections may or
may not be used for this application. The host supplies 3.3VDC and GND to power the module.

PSC autaniNet Module User’s Manual 6. Capabilities
CONFIDENTIAL AND PROPRIETARY
The information contained in this document is proprietary and confidential information of Autani, LLC. Any use of this
information without the expressed written consent of Autani, LLC is prohibited.
8 of 14
6. Capabilities
The P C autaniNet Module was designed to be used with 3
rd
party products such as Wired Wall
witches and Motion ensors. The P C autaniNet Module provides a cost-effective RF
transceiver for 2.4 GHz IEEE 802.15.4 ZigBee wireless networks. The P C autaniNet Module
is based on the Ember EM358x ystem-on-a-chip ( oC) and has been designed to support
larger, more secure, and resilient wireless networks. The EM358x is a 32-bit ARM Cortex-M3
Processor with a 2.4GHz IEEE 802.15.4-2003 RF transceiver.
The on-board EM358x ( oC) provides 24 GPIO ports to support all on-board functions such as
a Push-Button witch, two LED’s, Flash Memory for over-the-air firmware updates and
connections for programming and debugging. All GPIO’s are configurable as input, output, or
bi-directional and have an internal pull-up or pull-down. The Push-Button witch and LED’s are
used during installation to commission each device on the wireless network.
The P C autaniNet Module is powered from a 3.3VDC power source provided from the 3
rd
Party
product (Occupancy ensor, Wall witch, etc.) and communicates to the 3
rd
Party product via a
2-wire serial connection to control the operation of the 3
rd
Party product – such as controlling a
relay in an Occupancy ensor or Wall witch.
The P C autaniNet Module uses a wire antenna connected to J1 (IPEX4/MHF4 RF connector)
to communicate wirelessly in a mesh network topology using the ZigBee protocol (2.4GHz I M
band).
The P C autaniNet Module contains a shield that covers the RF circuitry.

PSC autaniNet Module User’s Manual
7. Connector Pin
Assignments
CONFIDENTIAL AND PROPRIETARY
The information contained in this document is proprietary and confidential information of Autani, LLC. Any use of this
information without the expressed written consent of Autani, LLC is prohibited.
9 of 14
7. Connector Pin Assignments
J1 (Off-Module Antenna Connector)
Pin Name Type Description
1 Ext. Ant. I/O U.FL Off-Module Antenna Connector
J2 (10-pin Program/Debug Header)
Pin Name Type Description
1 VDD Input +3.3VDC power supply to module
2 PC2/JTDO Output Program/Debug JTAG Data-Out
3 PC0/JR T Input Program/Debug JTAG Reset
4 PC3/JTDI Input Program/Debug JTAG Data-In
5 GND GND Power supply ground reference
6 JCLK Input Program/Debug JTAG Clock
7 PC4/JTM Input Program/Debug JTAG Mode elect
8 R T# Input Program/Debug Processor Reset
9 PA4/PTIEN Output Program/Debug Packet Trace Interface Enable
10 PA5/PTIDATA Input Program/Debug Packet Trace Interface Data
J3 (6-pin Receptacle) – Seral Communication
Pin Name Type Description
1 GND GND Power supply ground reference
2 VDD Input +3.3VDC power supply to module
3 TX Output UART interface transmit
4 RX Input UART interface receive
5 GPIO I/O General purpose input/output
6 WAKE Input Module wake-up interrupt signal

PSC autaniNet Module User’s Manual 8. Antenna
CONFIDENTIAL AND PROPRIETARY
The information contained in this document is proprietary and confidential information of Autani, LLC. Any use of this
information without the expressed written consent of Autani, LLC is prohibited.
10 of 14
8. Antenna
The P C autaniNet Module uses a wire antenna connected to J1 (I-PEX, MHF4 connector).
The P C autaniNet Module is FCC certified for use with the antenna shown below.
FCC Approved Antenna Specifications
Manufacturer henzhen Taida Century Technology Co., Ltd
Part Number WF2400-081IPEX
Type Whip traight (Wire)
Overall Wire Length 150mm +/-3mm
Material of Radiator Cu
Connector IPEX4 (MHF4)
.W.R. 2.0 max.
Frequency 2400 ~ 2500 MHz
Gain (typical) 1.5dBi +/-0.7
Impedance 50 ohm
Polarization Linear
Operating Temperature -40
o
C ~ +65
o
C
torage Temperature -40
o
C ~ +80
o
C
NOTE: Use of alternate antenna types or the same type with higher gain is not permitted without
additional testing and FCC approval.

PSC autaniNet Module User’s Manual 9. Dimensions
CONFIDENTIAL AND PROPRIETARY
The information contained in this document is proprietary and confidential information of Autani, LLC. Any use of this
information without the expressed written consent of Autani, LLC is prohibited.
11 of 14
9. Dimensions

PSC autaniNet Module User’s Manual 10. Certifications
CONFIDENTIAL AND PROPRIETARY
The information contained in this document is proprietary and confidential information of Autani, LLC. Any use of this
information without the expressed written consent of Autani, LLC is prohibited.
12 of 14
10. Certifications
10.1 FCC – United States
The PSC autaniNet Module complies with Part 15 of the Federal Communications Commission rules and
regulations. To continue compliance with Part 15 the end user MUST include a visi le la el on the
outside of the final product which indicates the internal radio module is FCC approved. The exterior
la el must use wording: “This device contains: FCC ID: V8NPSC1000179”. To meet the section 15.209
emissions requirements in the restricted ands of section 12.205, the transceiver transmitter power for the
EM358X can e set no higher than +8dBm for channels 11-25 (channel 26 to e disa led). Any
modifications to the PSC autaniNet Module may violate the rules of the FCC and make operation of the
module unlawful. The user is responsi le for o taining compliance for unintentional radiators on the
final product.
FCC Statement:
This device complies with part 15 of the FCC Rules. Operation is su ject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE 1: This equipment has een tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasona le protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can e determined y turning the equipment off and on, the user is encouraged to try to correct the
interference y one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation etween the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/ TV technician for help.
NOTE 2: The PSC autaniNet Module complies with the FCC RF radiation exposure limits set forth for an
uncontrolled environment. The PSC autaniNet Module must e installed and/or operated with a
minimum distance of 8 in. (20 cm.) etween the antenna and people.
FCC Caution: Changes or modifications not expressly approved y the party responsi le for
compliance could void the user’s authority to operate the equipment.

PSC autaniNet Module User’s Manual 10. Certifications
CONFIDENTIAL AND PROPRIETARY
The information contained in this document is proprietary and confidential information of Autani, LLC. Any use of this
information without the expressed written consent of Autani, LLC is prohibited.
13 of 14
10.2 IC – Canada
IC Statement:
The PSC autaniNet Module is IC certified. The la eling requirements for Industry Canada are similar to
those for FCC. A visi le la el must e placed on the outside of the final product which indicates the
internal radio module is IC approved. The exterior la el must use wording: “This device contains: IC:
7737A-PSC1000179”. The user is responsi le for the end product complying with ICES-003 (Unintentional
Radiators).
This device complies with ISED Canada license-exempt RSS standard(s). Operation is su ject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applica les aux appareils radio exempts
de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire
de rouillage, et (2) l'utilisateur de l'appareil doit accepter tout rouillage radioélectrique su i, même si le
rouillage est suscepti le d'en compromettre le fonctionnement.

PSC autaniNet Module User’s Manual 11. Handling and Storage
CONFIDENTIAL AND PROPRIETARY
The information contained in this document is proprietary and confidential information of Autani, LLC. Any use of this
information without the expressed written consent of Autani, LLC is prohibited.
14 of 14
11. Handling and Storage
11.1 Alterations
Any and all alterations to the P C autaniNet Module are highly discouraged and are completed
at the consumer’s risk. uch actions will invalidate any manufactures warranty and potentially
cause the module to violate FCC and IC certifications.
11.2 Handling
The P C autaniNet Module contains extremely sensitive electronic circuitry. Handle board with
proper E D protection at all times.
11.3 Storage
tore module in clean and dry environment. ee Electrical Specifications for additional details.